CVE Feed

In the Linux kernel, the following vulnerability has been resolved: ACPI: CPPC: Suppress UBSAN warning caused by field misuse The definition of reg->access_width changes depending on the reg->space_id type. Type ACPI_ADR_SPACE_PLATFORM_COMM uses access_width to indicate the PCC region, which can result in a UBSAN if the value is greater than 4. For example: UBSAN: shift-out-of-bounds in drivers/acpi/cppc_acpi.c:1090:9 shift exponent 32 is too large for 32-bit type 'int' CPU: 61 UID: 0 PID: 1220 Comm: (udev-worker) Not tainted 7.0.10-201.fc44.aarch64 #1 PREEMPT(lazy) Hardware name: To be filled by O.E.M. Call trace: ...(trimming) ubsan_epilogue+0x10/0x48 __ubsan_handle_shift_out_of_bounds+0xdc/0x1e0 cpc_write+0x4d0/0x670 cppc_set_perf+0x18c/0x490 cppc_cpufreq_cpu_init+0x1c8/0x380 [cppc_cpufreq] ... (trimming) Lets fix this by validating the region type, as well as whether access_width has a value. Then since we are returning bit_width directly for ACPI_ADR_SPACE_PLATFORM_COMM, drop the code correcting the size.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad_sigma_delta: fix clear_pending_event for registerless devices ad_sigma_delta_clear_pending_event() falls through to the status register read path for devices with has_registers = false and no rdy_gpiod. For such devices, ad_sd_read_reg() skips the address byte entirely and clocks raw MISO bytes with no address phase — making it byte-for-byte identical to reading conversion data. If a pending conversion result is present, this partially consumes it and corrupts the data stream for the subsequent ad_sd_read_reg() call in ad_sigma_delta_single_conversion(). Furthermore, with num_resetclks = 0 on these devices, data_read_len evaluates to 0. If the clocked byte has bit 7 clear, pending_event is set and the code attempts memset(data + 2, 0xff, 0 - 1), overflowing to SIZE_MAX and corrupting the heap. Fix by returning 0 immediately when neither rdy_gpiod nor has_registers is set. This is safe for all current registerless devices: ad7191 and ad7780 (with powerdown GPIO) are reset between conversions by CS deassertion, so there is no stale result to drain; ad7780 (without powerdown GPIO) and max11205 are continuously-converting and cycle ~DRDY at the output data rate regardless of whether the previous result was read, so the next falling edge fires naturally. A future registerless device that holds ~DRDY asserted until data is read would be broken by this early return and would require either num_resetclks set or a rdy-gpio. The same heap corruption is reachable on any device with rdy_gpiod set but num_resetclks = 0: if the GPIO indicates a pending event, the drain path executes memset(data + 2, 0xff, 0 - 1) regardless of has_registers. Add an explicit data_read_len == 0 guard after the pending event check; the stale result is then consumed by the first ad_sd_read_reg() call in ad_sigma_delta_single_conversion().

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad_sigma_delta: fix CS held asserted and state leaks In ad_sigma_delta_single_conversion(), set_mode(AD_SD_MODE_IDLE) and disable_one() were called from the out: block while keep_cs_asserted was still true. This caused any SPI transfer issued by those callbacks to carry cs_change=1, leaving CS permanently asserted after the conversion. Fix by moving both calls into the out_unlock: block, after keep_cs_asserted is cleared, matching the pattern already used in ad_sd_calibrate(). In the error path of ad_sd_buffer_postenable(), if an operation fails after set_mode(AD_SD_MODE_CONTINUOUS) has already succeeded (e.g. spi_offload_trigger_enable()), the device is left in continuous conversion mode with CS physically asserted. Additionally, bus_locked remaining true after spi_bus_unlock() causes subsequent SPI operations to call spi_sync_locked() without the bus lock actually held, allowing concurrent SPI access. Fix the error path by clearing keep_cs_asserted first, then calling set_mode(AD_SD_MODE_IDLE) to revert the device mode and deassert CS, then clearing bus_locked before releasing the bus. For devices that implement neither set_mode nor disable_one (such as MAX11205, which has no physical CS pin), no SPI transfer is issued during cleanup and the cs_change flag has no effect on any physical line.

In the Linux kernel, the following vulnerability has been resolved: iio: gyro: bmg160: bail out when bandwidth/filter is not in table bmg160_get_filter() walks bmg160_samp_freq_table[] looking for the entry matching the bw_bits value read from the chip: for (i = 0; i < ARRAY_SIZE(bmg160_samp_freq_table); ++i) { if (bmg160_samp_freq_table[i].bw_bits == bw_bits) break; } *val = bmg160_samp_freq_table[i].filter; If no entry matches, i ends up equal to the array size and the next line reads one slot past the end. bmg160_set_filter() has the same shape, driven by 'val' instead of bw_bits. smatch flags both: drivers/iio/gyro/bmg160_core.c:204 bmg160_get_filter() error: buffer overflow 'bmg160_samp_freq_table' 7 <= 7 drivers/iio/gyro/bmg160_core.c:222 bmg160_set_filter() error: buffer overflow 'bmg160_samp_freq_table' 7 <= 7 Return -EINVAL when no entry matches. The set_filter() path is reachable from userspace via the sysfs in_anglvel_filter_low_pass_3db_frequency interface, so userspace can trivially trigger the out-of-bounds read with a value that is not in bmg160_samp_freq_table[].filter.

In the Linux kernel, the following vulnerability has been resolved: iio: pressure: mpl115: fix runtime PM leak on read error mpl115_read_raw() takes a runtime PM reference with pm_runtime_get_sync() before reading the processed pressure or raw temperature, but on the read error path it returns without calling pm_runtime_put_autosuspend(). Each failed read therefore leaks a runtime PM reference and prevents the device from autosuspending. Drop the reference before checking the return value so both the success and error paths are balanced.

In the Linux kernel, the following vulnerability has been resolved: iio: temperature: tmp006: use devm_iio_trigger_register tmp006_probe() allocates the DRDY trigger with devm_iio_trigger_alloc() but registers it with plain iio_trigger_register(). The driver has no .remove() callback, so on module unload the trigger stays in the global trigger list while its memory is freed by devm, leaving a dangling entry. Switch to devm_iio_trigger_register() so the registration is undone in the same devm scope as the allocation.

In the Linux kernel, the following vulnerability has been resolved: vfio: Remove device debugfs before releasing devres VFIO device debugfs files created with debugfs_create_devm_seqfile() store a devres allocated debugfs_devm_entry as inode private data. vfio_unregister_group_dev() currently calls vfio_device_del() before vfio_device_debugfs_exit(), but device_del() releases devres. This can leave debugfs entries visible with stale inode private data while unregister waits for userspace references to drain. Remove the per-device debugfs tree before vfio_device_del(). The debugfs view is diagnostic only, so losing it at the start of unregister is preferable to preserving entries whose backing storage may already have been released. Complete the teardown by clearing the per-device debugfs root after removal. This matches the global debugfs root cleanup and prevents future users from mistaking a removed dentry for a live debugfs tree during the remainder of unregister.

In the Linux kernel, the following vulnerability has been resolved: tcp: restore RCU grace period in tcp_ao_destroy_sock Commit 51e547e8c89c ("tcp: Free TCP-AO/TCP-MD5 info/keys without RCU") removed the call_rcu() callback from tcp_ao_destroy_sock(), arguing that "the destruction of info/keys is delayed until the socket destructor" and therefore "no one can discover it anymore". That argument does not hold for the call site in tcp_connect() (net/ipv4/tcp_output.c:4327-4332). At that point the socket is in TCP_SYN_SENT, has already been inserted into the inet ehash by inet_hash_connect() in tcp_v4_connect(), and is therefore very much discoverable: any softirq running tcp_v4_rcv() on another CPU can take the socket out of the ehash, walk into tcp_inbound_hash(), and load tp->ao_info via implicit RCU before bh_lock_sock_nested() is taken on the destroying CPU. The reader path then enters __tcp_ao_do_lookup() (net/ipv4/tcp_ao.c:208) which re-loads tp->ao_info via rcu_dereference_check(); the re-load can still observe the (about-to-be-freed) pointer because there is no synchronize_rcu() between rcu_assign_pointer(tp->ao_info, NULL) and tcp_ao_info_free() in tcp_ao_destroy_sock(). The captured pointer is then walked at line 223: hlist_for_each_entry_rcu(key, &ao->head, node, ...) The writer's synchronous kfree() is free to complete between the line 218 re-fetch and the line 223 hlist iteration. The slab is reused (or simply LIST_POISON1-stamped if not yet reused) and the iteration walks attacker-controlled or poison memory in softirq context. Reproducer (no debug shim, stock x86_64 v7.1-rc2 SMP+KASAN, QEMU+KVM): an unprivileged uid=1000 process inside CLONE_NEWUSER|CLONE_NEWNET installs TCP_MD5SIG + TCP_AO_ADD_KEY on a TCP socket, sprays forged TCP-AO segments toward its eventual 4-tuple via raw sockets, then calls connect(). The md5-wins reconciliation in tcp_connect() fires tcp_ao_destroy_sock(); the softirq backlog reader on the loopback NAPI path crashes on the freed ao->head.first walk: Oops: general protection fault, probably for non-canonical address 0xfbd59c000000002f KASAN: maybe wild-memory-access in range [0xdead000000000178-0xdead00000000017f] CPU: 0 UID: 1000 PID: 100 Comm: repro_userns RIP: 0010:__tcp_ao_do_lookup+0x107/0x1c0 Call Trace: <IRQ> __tcp_ao_do_lookup+0x107/0x1c0 tcp_ao_inbound_lookup.constprop.0+0x12a/0x200 tcp_inbound_ao_hash+0x5ea/0x1520 tcp_inbound_hash+0x7ce/0x1240 tcp_v4_rcv+0x1e7a/0x3e10 ... Restore the RCU grace period: re-add struct rcu_head to tcp_ao_info and replace the synchronous tcp_ao_info_free() with a call_rcu() callback. Readers that captured tp->ao_info before rcu_assign_pointer NULLed it now see the object remain valid until rcu_read_unlock(). With the patch applied the reproducer runs cleanly for 2000 iterations on the same kernel build.

In the Linux kernel, the following vulnerability has been resolved: mm/damon/ops-common: handle extreme intervals in damon_hot_score() Fix three issues in damon_hot_score() that comes from wrong handling of extreme (zero or too high) monitoring intervals user setup. When the user sets sampling interval zero, damon_max_nr_accesses(), which is called from damon_hot_score(), causes a divide-by-zero. Needless to say, it is a problem. When the user sets the aggregation interval zero, the function returns zero. It is wrong, since the real maximum nr_acceses in the setup should be one. Worse yet, it can cause another divide-by-zero from its caller, damon_hot_score(), since it uses damon_max_nr_accesses() return value as a denominator. When the user sets the aggregation interval very high, damon_hot_score() could return a value out of [0, DAMOS_MAX_SCORE] range. Since the return value is used as an index to the regions_score_histogram array, which is DAMOS_MAX_SCORE+1 size, it causes out of bounds array access. The issues can be relatively easily reproduced like below. The sysfs write permission is required, though. # ./damo start --damos_action lru_prio --damos_quota_space 100M \ --damos_quota_interval 1s # cd /sys/kernel/mm/damon/admin/kdamonds/0 # echo 0 > contexts/0/monitoring_attrs/intervals/sample_us # echo 0 > contexts/0/monitoring_attrs/intervals/aggr_us # echo commit > state # dmesg [...] [ 131.329762] Oops: divide error: 0000 [#1] SMP NOPTI [...] [ 131.336089] RIP: 0010:damon_hot_score+0x27/0xd0 [...] Fix the divide-by-zero intervals problems by explicitly handling the zero intervals in damon_max_nr_accesses(). Fix the out-of-bound array access by applying [0, DAMOS_MAX_SCORE] bounds before returning from damon_hot_score(). The issue was discovered [1] by Sashiko.

In the Linux kernel, the following vulnerability has been resolved: hwrng: virtio: clamp device-reported used.len at copy_data() random_recv_done() stores the device-reported used.len directly into vi->data_avail. copy_data() then indexes vi->data[] using vi->data_idx (advanced by previous copy_data() calls) and issues a memcpy() without re-validating either value against the posted buffer size sizeof(vi->data) (SMP_CACHE_BYTES bytes, typically 32 or 64). A malicious or buggy virtio-rng backend can set used.len beyond sizeof(vi->data), steering the memcpy() past the end of the inline array into adjacent kmalloc-1k slab bytes. hwrng_fillfn() mixes those bytes into the guest RNG, and guest root can also observe them directly via /dev/hwrng. Concrete impact is inside the guest: - Memory-safety / hardening: any virtio-rng backend that over-reports used.len causes the driver to read past vi->data into unrelated slab contents. hwrng_fillfn() is a kernel thread that runs as soon as the device is probed; no guest userspace interaction is required to first-trigger the OOB. - Cross-boundary leak (confidential-compute threat model): a malicious hypervisor cooperating with a malicious or compromised guest root userspace can use /dev/hwrng as a leak channel for guest-kernel heap data. The host sets a large used.len, guest root reads /dev/hwrng, and the returned bytes contain guest kernel slab contents that were adjacent to vi->data. In practice, confidential-compute guests (SEV-SNP, TDX) usually disable virtio-rng entirely, so this path is narrow, but the fix is still worth carrying because the underlying memory-safety bug contaminates the guest RNG on any host. KASAN confirms the OOB on a 7.1-rc4 guest whose virtio-rng backend has been patched to report used.len = 0x10000: BUG: KASAN: slab-out-of-bounds in virtio_read+0x394/0x5d0 Read of size 64 at addr ffff88800ae0ba20 by task hwrng/52 Call Trace: __asan_memcpy+0x23/0x60 virtio_read+0x394/0x5d0 hwrng_fillfn+0xb2/0x470 kthread+0x2cc/0x3a0 Allocated by task 1: probe_common+0xa5/0x660 virtio_dev_probe+0x549/0xbc0 The buggy address belongs to the object at ffff88800ae0b800 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 0 bytes to the right of allocated 544-byte region [ffff88800ae0b800, ffff88800ae0ba20) Same class of bug as commit c04db81cd028 ("net/9p: Fix buffer overflow in USB transport layer"), which hardened usb9pfs_rx_complete() against unchecked device-reported length in the USB 9p transport. With the clamp at point of use and array_index_nospec() in place, the same harness boots cleanly: copy_data() returns zero for the bogus report, the device-supplied bytes after data_idx are discarded, and the driver issues a fresh request.

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: run gadget disconnect from sleepable suspend context dwc3_gadget_suspend() takes dwc->lock with IRQs disabled and then calls dwc3_disconnect_gadget(). For async callbacks that helper only uses plain spin_unlock()/spin_lock(), so the gadget ->disconnect() callback still runs with IRQs disabled and any sleepable callback trips Lockdep. This issue was found by our static analysis tool and then manually reviewed against the current tree. The grounded PoC kept the dwc3_gadget_suspend() -> dwc3_disconnect_gadget() -> gadget_driver->disconnect() chain, and Lockdep reported: BUG: sleeping function called from invalid context gadget_disconnect+0x21/0x39 [vuln_msv] dwc3_gadget_suspend.constprop.0+0x2b/0x42 [vuln_msv] Keep the disconnect callback selection in one common helper, but add a sleepable suspend-side wrapper which snapshots the callback under dwc->lock and then runs it after spin_unlock_irqrestore(). The regular event path still uses the existing spin_unlock()/spin_lock() window.

In the Linux kernel, the following vulnerability has been resolved: gpio: eic-sprd: use raw_spinlock_t in the irq startup path sprd_eic_irq_unmask() enables the GPIO IRQ and then updates controller state through sprd_eic_update(), which takes sprd_eic->lock with spin_lock_irqsave(). The callback can be reached from irq_startup() while setting up a requested IRQ. That path is not sleepable, but on PREEMPT_RT a regular spinlock_t becomes a sleeping lock. This issue was found by our static analysis tool and then manually reviewed against the current tree. The grounded PoC kept the request_threaded_irq() -> __setup_irq() -> irq_startup() -> sprd_eic_irq_unmask() -> sprd_eic_update() carrier and used the original spin_lock_irqsave(&sprd_eic->lock) edge. Lockdep BUG: sleeping function called from invalid context hardirqs last disabled at ... __setup_irq.constprop.0 ... [vuln_msv] sprd_rt_spin_lock_irqsave+0x1c/0x30 [vuln_msv] sprd_eic_update.constprop.0+0x48/0x90 [vuln_msv] sprd_eic_irq_unmask.constprop.0+0x35/0x50 [vuln_msv] __setup_irq.constprop.0+0xd/0x30 [vuln_msv] Convert the Spreadtrum EIC controller lock to raw_spinlock_t. The locked section only serializes MMIO register updates and does not contain sleepable operations, so keeping it non-sleeping is appropriate for the irqchip callbacks.

In the Linux kernel, the following vulnerability has been resolved: netfilter: ebtables: zero chainstack array sashiko reports: looking at ebtables table translation, could a sparse cpu_possible_mask lead to an uninitialized pointer free? If cpu_possible_mask is sparse (for example, CPU 0 and CPU 2 are possible, but CPU 1 is not), the allocation loop skips CPU 1. If vmalloc_node() fails at CPU 2, the cleanup loop will blindly decrement and call vfree() on newinfo->chainstack[1]. Not a real-world bug, such allocation isn't expected to fail in the first place.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: bnep: pin L2CAP connection during netdev registration bnep_add_connection() reads the L2CAP connection without holding the channel lock, then passes its HCI device to register_netdev(). Controller teardown can clear and release that connection concurrently, leaving the network device registration path to dereference a freed parent device. Take a reference to the L2CAP connection while holding the channel lock. Retain it until register_netdev() has taken the parent device reference.

In the Linux kernel, the following vulnerability has been resolved: HID: wacom: fix slab-out-of-bounds write in wacom_wac_queue_insert wacom_wac_queue_insert() calls kfifo_skip() in a loop when the kfifo doesn't have enough space for the incoming report. If the kfifo is empty, kfifo_skip() reads stale data left in the kmalloc'd buffer via __kfifo_peek_n() and interprets it as a record length, advancing fifo->out by that garbage value. This corrupts the internal kfifo state, causing kfifo_unused() to return a value much larger than the actual buffer size, which bypasses __kfifo_in_r()'s guard: if (len + recsize > kfifo_unused(fifo)) return 0; kfifo_copy_in() then performs an out-of-bounds memcpy, writing up to 3842 bytes past the 256-byte buffer. Add a !kfifo_is_empty() condition to the while loop so kfifo_skip() is never called on an empty fifo, and check the return value of kfifo_in() to reject reports that are too large for the fifo.

In the Linux kernel, the following vulnerability has been resolved: xfs: fix exchmaps reservation limit check xfs_exchmaps_estimate_overhead() adds the bmbt and rmapbt overhead to a local resblks variable, but the final UINT_MAX check still tests req->resblks. That is the reservation value from before the overhead was added. The computed value is stored back in req->resblks and later passed to xfs_trans_alloc(), whose block reservation argument is unsigned int. Check the computed reservation so the existing limit applies to the value that will be used.

In the Linux kernel, the following vulnerability has been resolved: udf: validate free block extents against the partition length udf_free_blocks() checks the logical block number and count against the partition length, but drops the extent offset from that final bound. A crafted extent can pass the guard while logicalBlockNum + offset + count points past the partition, which later indexes past the space bitmap array. A single ftruncate(2) on a file backed by such an extent reliably panics the kernel. This is a local availability issue. On desktop systems where UDisks/polkit allows the active user to mount removable UDF media without CAP_SYS_ADMIN, an unprivileged local user can supply the crafted filesystem and trigger the panic by truncating a writable file on it. Systems that require root or CAP_SYS_ADMIN to mount the image have a higher prerequisite. No confidentiality or integrity impact is claimed: the reproduced primitive is an out-of-bounds read of a bitmap pointer slot followed by a kernel panic. Use the already computed logicalBlockNum + offset + count value for the partition length check. Also make load_block_bitmap() reject an out-of-range block group before indexing s_block_bitmap[], so corrupted callers cannot walk past the flexible array.

In the Linux kernel, the following vulnerability has been resolved: nvmet: fix pre-auth out-of-bounds heap read in Discovery Get Log Page nvmet_execute_disc_get_log_page() validates only the dword alignment of the host-supplied Log Page Offset (lpo). The 64-bit offset is then added to a small kzalloc'd buffer that holds the discovery log page and the result is passed straight to nvmet_copy_to_sgl(), which memcpy()s data_len bytes out to the host with no source-side bound check: u64 offset = nvmet_get_log_page_offset(req->cmd); /* 64-bit host */ size_t data_len = nvmet_get_log_page_len(req->cmd); /* 32-bit host */ ... if (offset & 0x3) { ... } /* only check */ ... alloc_len = sizeof(*hdr) + entry_size * discovery_log_entries(req); buffer = kzalloc(alloc_len, GFP_KERNEL); ... status = nvmet_copy_to_sgl(req, 0, buffer + offset, data_len); The Discovery controller is unauthenticated -- nvmet_host_allowed() returns true unconditionally for the discovery subsystem -- so the call is reachable pre-authentication by any TCP/RDMA/FC peer that can reach the nvmet target. With a discovery log page of ~1 KiB, an attacker requesting up to 4 KiB starting at offset == alloc_len reads the next slab page out and gets its content returned over the fabric (an empirical run on a default nvmet-tcp loopback target leaked 81 canonical kernel pointers in one Get Log Page response). Pointing the offset at unmapped kernel memory faults the in-kernel memcpy and crashes (or panics, on panic_on_oops=1) the target host instead. The attacker-controlled source-side offset pattern "nvmet_copy_to_sgl(req, 0, buffer + ATTACKER_OFFSET, ...)" is unique to nvmet_execute_disc_get_log_page in the entire nvmet codebase: every other Get Log Page handler in admin-cmd.c either ignores lpo (and silently starts every response at offset 0) or tracks a local destination offset with a fixed source pointer. Validate the host-supplied offset against the log page size, cap the copy length to what is actually available, and zero-fill any remainder of the host transfer buffer. The zero-fill matches the existing short-response pattern in nvmet_execute_get_log_changed_ns() (admin-cmd.c) and prevents leaking transport SGL contents when the host asks for more bytes than the log page contains.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - validate RSA CRT component lengths The generic RSA key parser (rsa_helper.c) bounds each CRT component (p, q, dp, dq, qinv) by the modulus size n_sz, but qat_rsa_setkey_crt() allocates half-size DMA buffers (key_sz / 2) and right-aligns each component with: memcpy(dst + half_key_sz - len, src, len) When a CRT component is larger than half_key_sz the subtraction underflows and memcpy writes past the DMA buffer, causing memory corruption. Add a len > half_key_sz check next to the existing !len check for each of the five CRT components so the driver falls back to the non-CRT path instead of writing out of bounds.

In the Linux kernel, the following vulnerability has been resolved: iommufd: Set upper bounds on cache invalidation entry_num and entry_len iommufd_hwpt_invalidate() takes a user-controlled entry_num and entry_len, each bounded only by U32_MAX. An entry_len beyond the kernel's struct size makes the copy helper verify the extra bytes are zero, scanning that excess in one uninterruptible pass; a multi-gigabyte value over zeroed user memory trips the soft-lockup watchdog. A large entry_num is the other half, driving the backend invalidation loop with no reschedule. The VT-d nested handler, for one, copies each entry and flushes caches per iteration, pinning the CPU on a non-preemptible kernel. Cap both in the ioctl. entry_len is held under PAGE_SIZE, above any request struct, and entry_num under 1 << 19, the order of a hardware invalidation queue and well beyond any real batch, bounding the per-call loop length.

In the Linux kernel, the following vulnerability has been resolved: KVM: SEV: Pin source page for write when adding CPUID data for SNP guest When populating a guest_memfd instance with the initial CPUID data for an SNP guest, acquire a writable pin on the source page as KVM will write back the "correct" CPUID information if the userspace provided data is rejected by trusted firmware. Because KVM writes to the source page using a kernel mapping, pinning for read could result in KVM clobbering read-only memory. Note, well-behaved VMMs are unlikely to be affected, as CPUID information is almost always dynamically generated by userspace, i.e. it's unlikely for the CPUID information to be backed by a read-only mapping. [sean: rewrite shortlog and changelog, tag for stable@]

In the Linux kernel, the following vulnerability has been resolved: Input: touchwin - reset the packet index on every complete packet tw_interrupt() accumulates each non-zero serial byte into a fixed three-byte buffer with a running index that is only reset once a full packet has been received *and* the device's two Y bytes agree: tw->data[tw->idx++] = data; if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) { ... tw->idx = 0; } The reset is gated on tw->data[1] == tw->data[2], a value the device controls. A malicious, malfunctioning or counterfeit Touchwindow peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the index reaches TW_LENGTH without the equality holding, is never reset, and keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte array and the rest of the heap-allocated struct tw, one attacker-chosen byte at a time -- an unbounded, device-driven heap out-of-bounds write. Reset the index on every completed packet and report an event only when the two Y bytes match, like the other serio touchscreen drivers do.

In the Linux kernel, the following vulnerability has been resolved: tty: serial: samsung: Remove redundant port lock acquisition in rx helpers Sashiko identified a deadlock when the console flow is engaged [1]. When console flow control is enabled (UPF_CONS_FLOW), s3c24xx_serial_stop_tx() calls s3c24xx_serial_rx_enable() and s3c24xx_serial_start_tx() calls s3c24xx_serial_rx_disable(). The serial core framework invokes the .stop_tx() and .start_tx() callbacks with the port->lock spinlock already held. Furthermore, all internal driver paths that invoke stop_tx (such as the DMA TX completion handler s3c24xx_serial_tx_dma_complete() or the PIO TX IRQ handler s3c24xx_serial_tx_irq()) also acquire port->lock prior to calling it. (Note that s3c24xx_serial_start_tx() is only invoked by the serial core). However, s3c24xx_serial_rx_enable() and s3c24xx_serial_rx_disable() unconditionally attempt to acquire port->lock again using uart_port_lock_irqsave(). Since spinlocks are not recursive, this causes a deadlock on the same CPU when console flow control is engaged. Remove the redundant lock acquisition from both rx helper functions.

In the Linux kernel, the following vulnerability has been resolved: iio: buffer: hw-consumer: free scan_mask on buffer release The scan_mask lifetime changed in commit 9a2e1233d38c ("iio: buffer: hw-consumer: remove redundant scan_mask flexible array"). Before that change, the scan mask storage was embedded in struct hw_consumer_buffer, so iio_hw_buf_release() could free the whole allocation with a single kfree(hw_buf). That commit moved the scan mask to a separate bitmap_zalloc() allocation stored in buffer.scan_mask, but left iio_hw_buf_release() unchanged. Free the scan mask in iio_hw_buf_release() before freeing the buffer wrapper.

In the Linux kernel, the following vulnerability has been resolved: ALSA: aoa: check snd_ctl_new1() return value snd_ctl_new1() can return NULL when memory allocation fails. In layout.c, the function does not check the return value before dereferencing ctl->id.name or passing to aoa_snd_ctl_add(), which can lead to a NULL pointer dereference. Add NULL checks after snd_ctl_new1() calls and return early if any fails.

In the Linux kernel, the following vulnerability has been resolved: binder: fix UAF in binder_thread_release() When a thread exits, binder_thread_release() walks its transaction stack to clear the t->from and t->to_proc that correspond with the exiting thread. However, a process dying in parallel might attempt to kfree some of these transactions. And if one of them has no associated t->to_proc, the t->to_proc->inner_lock will not be acquired. This means that transaction accesses in binder_thread_release() after t->to_proc has been cleared might race with binder_free_transaction() and cause a use-after-free error as reported by KASAN: ================================================================== BUG: KASAN: slab-use-after-free in binder_thread_release+0x5d0/0x798 Write of size 8 at addr ffff000016627500 by task X/715 CPU: 17 UID: 0 PID: 715 Comm: X Not tainted 7.1.0-rc5-00149-g8fde5d1d47f6 #30 PREEMPT Hardware name: linux,dummy-virt (DT) Call trace: binder_thread_release+0x5d0/0x798 binder_ioctl+0x12c0/0x299c [...] Allocated by task 717 on cpu 18 at 67.267803s: __kasan_kmalloc+0xa0/0xbc __kmalloc_cache_noprof+0x174/0x444 binder_transaction+0x554/0x8150 binder_thread_write+0xa30/0x4354 binder_ioctl+0x20f0/0x299c [...] Freed by task 202 on cpu 18 at 90.416221s: __kasan_slab_free+0x58/0x80 kfree+0x1a0/0x4a4 binder_free_transaction+0x150/0x294 binder_send_failed_reply+0x398/0x6d8 binder_release_work+0x3e4/0x4ec binder_deferred_func+0xbd8/0x104c [...] ================================================================== In order to avoid this, make sure that binder_free_transaction() reads the t->to_proc under the transaction lock. This will serialize the transaction release with the accesses in binder_thread_release(). Plus, it matches the documented locking rules for @to_proc.

In the Linux kernel, the following vulnerability has been resolved: iio: accel: bmc150: clamp the device-reported FIFO frame count __bmc150_accel_fifo_flush() copies the number of samples the device reports in its hardware FIFO into an on-stack buffer u16 buffer[BMC150_ACCEL_FIFO_LENGTH * 3]; which is sized for at most BMC150_ACCEL_FIFO_LENGTH (32) samples. The frame count is read from the FIFO_STATUS register and only masked to its 7 valid bits: count = val & 0x7F; so it can be 0..127. The only other limit applied to it is the optional caller-supplied sample budget: if (samples && count > samples) count = samples; which does not constrain count on the flush-all path (samples == 0), and leaves it well above 32 whenever samples is larger. count samples are then transferred into buffer[]: bmc150_accel_fifo_transfer(data, (u8 *)buffer, count); bmc150_accel_fifo_transfer() reads count * 6 bytes through regmap, so a malfunctioning, malicious or counterfeit accelerometer (or an attacker tampering with the I2C/SPI bus) that reports up to 127 frames writes up to 762 bytes into the 192-byte buffer: a stack out-of-bounds write of up to 570 bytes that clobbers the stack canary, saved registers and the return address. Clamp count to BMC150_ACCEL_FIFO_LENGTH, the number of samples buffer[] is sized for, before the transfer, mirroring the watermark clamp already done in bmc150_accel_set_watermark(). A well-formed flush reports at most BMC150_ACCEL_FIFO_LENGTH frames, so legitimate devices are unaffected.

In the Linux kernel, the following vulnerability has been resolved: rust_binder: use a u64 stride when cleaning up the offsets array Allocation's Drop walks the offsets array (binder_size_t = u64 entries), cleaning up the objects, but it used usize instead of u64 for both the stride and the per-entry read. On 64-bit kernels (usize == u64) this is harmless, but on 32-bit kernels it walks the 8-byte entries in 4-byte steps, iterating an N-entry array 2N times, and reads the always-zero high word as offset 0, cleaning up the object at offset 0 N extra times. As a result the referenced node or handle ends up with a lower reference count than it actually has (a refcount over-decrement), and binder's reference accounting is corrupted; for example, the owner can be notified of a strong reference release (BR_RELEASE) even though references still remain. Change the stride to u64, and read each entry as a u64, narrowing it to usize with try_into(). On 32-bit ARM, when this over-decrement would drive a count below zero, the driver's existing refcount guard refuses it and fires: rust_binder: Failure: refcount underflow!

In the Linux kernel, the following vulnerability has been resolved: virtio_pci: fix vq info pointer lookup via wrong index Unbinding a virtio balloon device: echo virtio0 > /sys/bus/virtio/drivers/virtio_balloon/unbind triggers a NULL pointer dereference. The dmesg says: BUG: kernel NULL pointer dereference, address: 0000000000000008 [...] RIP: 0010:__list_del_entry_valid_or_report+0x5/0xf0 Call Trace: <TASK> vp_del_vqs+0x121/0x230 remove_common+0x135/0x150 virtballoon_remove+0xee/0x100 virtio_dev_remove+0x3b/0x80 device_release_driver_internal+0x187/0x2c0 unbind_store+0xb9/0xe0 kernfs_fop_write_iter.llvm.11660790530567441834+0xf6/0x180 vfs_write+0x2a9/0x3b0 ksys_write+0x5c/0xd0 do_syscall_64+0x54/0x230 entry_SYSCALL_64_after_hwframe+0x29/0x31 [...] </TASK> The virtio_balloon device registers 5 queues (inflate, deflate, stats, free_page, reporting) but only the first two are unconditional. The stats, free_page and reporting queues are each conditional on their respective feature bits. When any of these features are absent, the corresponding vqs_info entry has name == NULL, creating holes in the array. The root cause is an indexing mismatch introduced when vq info storage was changed to be passed as an argument. vp_find_vqs_msix() and vp_find_vqs_intx() store the info pointer at vp_dev->vqs[i], where 'i' is the caller's sparse array index. However, the virtqueue itself gets vq->index assigned from queue_idx, a dense index that skips NULL entries. When holes exist, 'i' and queue_idx diverge. Later, vp_del_vqs() looks up info via vp_dev->vqs[vq->index] using the dense index into the sparsely-populated array, and hits NULL. Fix this by storing info at vp_dev->vqs[queue_idx] instead of vp_dev->vqs[i], so the store index matches the lookup index (vq->index). Apply the fix to both the MSIX and INTX paths.

In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix WEP length underflow and OOB read in OnAuth() OnAuth() has two bugs in the shared-key authentication path. When the Privacy bit is set, rtw_wep_decrypt() is called without verifying that the frame is long enough to contain a valid WEP IV and ICV. Inside rtw_wep_decrypt(), length is computed as: length = len - WLAN_HDR_A3_LEN - iv_len and then passed as (length - 4) to crc32_le(). If len is less than WLAN_HDR_A3_LEN + iv_len + icv_len (32 bytes), length - 4 is negative and, after the implicit cast to size_t, causes crc32_le() to read far beyond the frame buffer. Add a minimum length check before accessing the IV field and calling the decryption path. When processing a seq=3 response, rtw_get_ie() stores the Challenge Text IE length in ie_len, but the subsequent memcmp() always reads 128 bytes regardless of ie_len. IEEE 802.11 mandates a challenge text of exactly 128 bytes; reject any IE whose length field differs, matching the check already applied to OnAuthClient().

In the Linux kernel, the following vulnerability has been resolved: ksmbd: prevent path traversal bypass by restricting caseless retry ksmbd_vfs_path_lookup() enforces LOOKUP_BENEATH to restrict path resolution within the share root. When a crafted path attempts to escape the share boundary using parent-directory components ('..'), vfs_path_parent_lookup() detects this and immediately fails, returning -EXDEV. However, a bug exists in __ksmbd_vfs_kern_path() under caseless mode. The function fails to intercept the -EXDEV error and erroneously falls through to the caseless retry logic, which is intended only for genuinely missing files. During this retry process, the path is reconstructed, leading to an unintended LOOKUP_BENEATH bypass that allows write-capable users to create zero-length files or directories outside the exported share. Fix this by ensuring that the execution only proceeds to the caseless lookup retry when the error is specifically -ENOENT. Any other errors, such as -EXDEV from a path traversal attempt, must be returned immediately.

In the Linux kernel, the following vulnerability has been resolved: writeback: fix race between cgroup_writeback_umount() and inode_switch_wbs() When a container exits, the following BUG_ON() is occasionally triggered: ================================================================== VFS: Busy inodes after unmount of sdb (ext4) ------------[ cut here ]------------ kernel BUG at fs/super.c:695! CPU: 3 PID: 6 Comm: containerd-shim Tainted: G OE K 6.6 #1 pstate: 63400009 (nZCv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--) pc : generic_shutdown_super+0xf0/0x100 lr : generic_shutdown_super+0xf0/0x100 Call trace: generic_shutdown_super+0xf0/0x100 kill_block_super+0x20/0x48 ext4_kill_sb+0x28/0x60 deactivate_locked_super+0x54/0x130 deactivate_super+0x84/0xa0 cleanup_mnt+0xa4/0x140 __cleanup_mnt+0x18/0x28 task_work_run+0x78/0xe0 do_notify_resume+0x204/0x240 ================================================================== The root cause is a race between cgroup_writeback_umount() and inode_switch_wbs()/cleanup_offline_cgwb(). There is a window between inode_prepare_wbs_switch() returning true and the subsequent wb_queue_isw() call. Following is the process that triggers the issue: CPU A (umount) | CPU B (writeback) ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ inode_switch_wbs/cleanup_offline_cgwb atomic_inc(&isw_nr_in_flight) inode_prepare_wbs_switch -> passes SB_ACTIVE check __iget(inode) generic_shutdown_super sb->s_flags &= ~SB_ACTIVE cgroup_writeback_umount(sb) smp_mb() atomic_read(&isw_nr_in_flight) rcu_barrier() -> no pending RCU callbacks flush_workqueue(isw_wq) -> nothing queued, returns evict_inodes(sb) -> Inode skipped as isw still holds a ref. sop->put_super(sb) /* destroys percpu counters */ -> VFS: Busy inodes after unmount! wb_queue_isw() queue_work(isw_wq, ...) /* later in work function */ inode_switch_wbs_work_fn process_inode_switch_wbs iput() -> evict percpu_counter_dec() // UAF! Fix this by extending the RCU read-side critical section in inode_switch_wbs() and cleanup_offline_cgwb() to cover from inode_prepare_wbs_switch() through wb_queue_isw(). Since there is no sleep in this window, rcu_read_lock() can be used. Then add a synchronize_rcu() in cgroup_writeback_umount() before the existing rcu_barrier(), so that all in-flight switchers that have passed the SB_ACTIVE check have completed queue_work() before flush_workqueue() is called. The existing rcu_barrier() is intentionally retained so this fix can be backported unchanged to stable kernels (5.10.y, 6.6.y, ...) that still queue switches via queue_rcu_work(). It is a no-op on current mainline (since commit e1b849cfa6b6 ("writeback: Avoid contention on wb->list_lock when switching inodes")) and is removed in a follow-up patch.

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp - Do not initialize SNP for ioctl(SNP_VLEK_LOAD) Sashiko notes: > if SEV initialization fails and KVM is actively running normal VMs, could a > userspace process trigger this code path via /dev/sev ioctls (e.g., > SEV_PDH_GEN) and zero out MSR_VM_HSAVE_PA globally? Would the next VMRUN > execution for an active VM trigger a general protection fault and crash the > host? The SEV firmware docs for SNP_VLEK_LOAD note: > On SNP_SHUTDOWN, the VLEK is deleted. That is, the initialization/shutdown wrapper here is pointless, because the firmware immediately throws away the key anyway. Instead, refuse to do anything if SNP has not been previously initialized. This is an ABI break: before, this was a no-op and almost certainly a mistake by userspace, and now it returns -ENODEV. ABI compatibility could be maintained here by simply returning 0 in the check instead.

In the Linux kernel, the following vulnerability has been resolved: ethtool: tsconfig: fix missing ethnl_ops_complete() tsconfig_prepare_data() calls ethnl_ops_begin(), we need to call ethnl_ops_complete() before returning the error.

In the Linux kernel, the following vulnerability has been resolved: userfaultfd: gate must_wait writability check on pte_present() userfaultfd_must_wait() and userfaultfd_huge_must_wait() read the PTE without taking the page table lock and then apply pte_write() / huge_pte_write() to it. Those accessors decode bits from the present encoding only; on a swap or migration entry they read the offset bits that happen to share the same position and return an undefined result. The intent of the check is "is this fault still WP-blocked?". A non-marker swap entry means the page is in transit -- the userfault context the original fault delivered against is no longer the same, and the swap-in or migration completion path will re-deliver a fresh fault if userspace still needs to handle it. Worst case under the current code the garbage write bit says "wait", and the thread stays asleep until a UFFDIO_WAKE that may never arrive. Gate the writability check on pte_present() so the lockless re-check only inspects present-PTE bits when the entry is actually present. The non-present, non-marker case returns "don't wait" and lets the fault path retry.

In the Linux kernel, the following vulnerability has been resolved: ALSA: ice1712: check snd_ctl_new1() return value snd_ctl_new1() can return NULL when memory allocation fails. The ice1712 driver calls snd_ctl_new1() without checking the return value before dereferencing the pointer in multiple places (ice1712.c, ice1724.c, aureon.c), which can lead to NULL pointer dereferences. Add NULL checks after snd_ctl_new1() calls and return -ENOMEM if any fails.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ti-ads1119: fix PM reference leak in buffer preenable ads1119_triggered_buffer_preenable() resumes the device with pm_runtime_resume_and_get() before starting a conversion. If i2c_smbus_write_byte() fails, the function returns the error directly and leaves the runtime PM usage counter elevated. The matching postdisable callback is not called when preenable fails, so the reference is leaked and the device may remain runtime-active indefinitely. Store the I2C transfer result in ret and drop the runtime PM reference on failure before returning the error.

In the Linux kernel, the following vulnerability has been resolved: xhci: sideband: fix ring sg table pages leak xhci_ring_to_sgtable() allocates a temporary pages array and uses it to build the returned sg_table with sg_alloc_table_from_pages(). The error paths free the pages array, but the success path returns the sg_table without freeing it. This leaks the temporary array every time a sideband client gets an endpoint or event ring buffer. Free the pages array after sg_alloc_table_from_pages() succeeds. The returned sg_table has its own scatterlist entries and does not depend on the temporary array after construction.

In the Linux kernel, the following vulnerability has been resolved: media: nxp: imx8-isi: Fix use-after-free on remove KASAN reports a slab-use-after-free in __media_entity_remove_link() during rmmod of imx8_isi: BUG: KASAN: slab-use-after-free in __media_entity_remove_link+0x608/0x650 Read of size 2 at addr ffff0000d47cb02a by task rmmod/724 Call trace: __media_entity_remove_link+0x608/0x650 __media_entity_remove_links+0x78/0x144 __media_device_unregister_entity+0x150/0x280 media_device_unregister_entity+0x48/0x68 v4l2_device_unregister_subdev+0x158/0x300 v4l2_async_unbind_subdev_one+0x22c/0x358 v4l2_async_nf_unbind_all_subdevs+0xfc/0x1c0 v4l2_async_nf_unregister+0x5c/0x14c mxc_isi_remove+0x124/0x2a0 [imx8_isi] Allocated by task 249: __kmalloc_noprof+0x27c/0x690 mxc_isi_crossbar_init+0x22c/0x560 [imx8_isi] Freed by task 724: kfree+0x1e4/0x5b0 mxc_isi_crossbar_cleanup+0x34/0x80 [imx8_isi] mxc_isi_remove+0x11c/0x2a0 [imx8_isi] The problem is that mxc_isi_remove() calls mxc_isi_crossbar_cleanup() before mxc_isi_v4l2_cleanup(). The crossbar cleanup frees the media entity pads, but the subsequent v4l2 cleanup still tries to remove media links that reference those pads. Fix this by calling mxc_isi_v4l2_cleanup() before mxc_isi_crossbar_cleanup() to ensure all media entities are properly unregistered while the pads are still valid.

In the Linux kernel, the following vulnerability has been resolved: Input: iforce - bound the device-reported force-feedback effect index iforce_process_packet() handles a status report (packet id 0x02) by taking a force-feedback effect index straight from the device wire and using it to address the per-effect state array: i = data[1] & 0x7f; if (data[1] & 0x80) { if (!test_and_set_bit(FF_CORE_IS_PLAYED, iforce->core_effects[i].flags)) ... } else if (test_and_clear_bit(FF_CORE_IS_PLAYED, iforce->core_effects[i].flags)) { ... } The index is masked only with 0x7f, so it ranges 0..127, but core_effects[] holds only IFORCE_EFFECTS_MAX (32) entries. For an index of 32..127 the test_and_set_bit()/test_and_clear_bit() is an out-of-bounds single-bit read-modify-write past the array. core_effects[] is the second-to-last member of struct iforce, so the write lands in the trailing members and beyond the embedding kzalloc()'d iforce_serio / iforce_usb object. data[1] is unvalidated device payload on both transports (the USB interrupt endpoint and serio), and the status path is not gated on force feedback being present, so a malicious or counterfeit device can set or clear a bit at an attacker-chosen offset past the object. Reject an out-of-range index instead of indexing with it. Bound against the array dimension IFORCE_EFFECTS_MAX rather than dev->ff->max_effects so the check guarantees memory safety regardless of how many effects the device registered. A legitimate "effect started/stopped" status always carries an index below IFORCE_EFFECTS_MAX, so well-formed devices are unaffected; the neighbouring mark_core_as_ready() loop is already bounded and is left untouched.

In the Linux kernel, the following vulnerability has been resolved: USB: chaoskey: Fix slab-use-after-free in chaoskey_release() The chaoskey driver has a use-after-free bug in its release routine. If the user closes the device file after the USB device has been unplugged, a debugging log statement will try to access the usb_interface structure after it has been deallocated: BUG: KASAN: slab-use-after-free in dev_driver_string (drivers/base/core.c:2406) Read of size 8 at addr ffff888168e8a0b8 by task chaoskey_raw_re/10106 Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:94 lib/dump_stack.c:120) print_report (mm/kasan/report.c:378 mm/kasan/report.c:482) kasan_report (mm/kasan/report.c:595) dev_driver_string (drivers/base/core.c:2406) __dynamic_dev_dbg (lib/dynamic_debug.c:906) chaoskey_release (drivers/usb/misc/chaoskey.c:323) __fput (fs/file_table.c:510) fput_close_sync (fs/file_table.c:615) __x64_sys_close (fs/open.c:1507 fs/open.c:1492 fs/open.c:1492) do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) The driver's last reference to the interface structure is dropped in the chaoskey_free() routine, so the code must not use the interface -- even in a debugging statement -- after that routine returns. (Exception: If we know that another reference is held by someone else, such as the device core while the disconnect routine runs, there's no problem. Thanks to Johan Hovold for pointing this out.) Since the bad access is part of an unimportant debugging statement, we can fix the problem simply by removing the whole statement.

In the Linux kernel, the following vulnerability has been resolved: io_uring/io-wq: re-check IO_WQ_BIT_EXIT for each linked work item commit 10dc95939817 ("io_uring/io-wq: check IO_WQ_BIT_EXIT inside work run loop") fixed the obvious case where io_worker_handle_work() took one exit-bit snapshot before draining pending work, but the fix stops one level too early. io_worker_handle_work() now re-checks IO_WQ_BIT_EXIT in its outer work run loop, yet it still snapshots that bit once before processing a whole dependent linked-work chain. If io_wq_exit_start() sets IO_WQ_BIT_EXIT after the first linked item has started, the remaining linked items can still reuse stale do_kill = false, skip IO_WQ_WORK_CANCEL, and continue running after exit has begun. Move the check further inside, so it covers linked items too. Note: this is a syzbot special as it loves setting up tons of slow linked work on weird devices like msr that take forever to read, and immediately close the ring. Exit then takes a long time.

In the Linux kernel, the following vulnerability has been resolved: USB: ulpi: fix memory leak on registration failure The allocated device name is never freed on early ULPI device registration failures. Fix this by initialising the device structure earlier and releasing the initial reference whenever registration fails.

In the Linux kernel, the following vulnerability has been resolved: rust: block: fix GenDisk cleanup paths GenDiskBuilder::build() still has fallible work after __blk_mq_alloc_disk(), but its error path only recovers the foreign queue data. That leaks the temporary gendisk and request_queue until later teardown. If the caller moved the last Arc<TagSet<T>> into build(), the leaked queue can retain blk-mq state after the tag set is dropped. Fix the pre-registration failure path by dropping the temporary gendisk reference with put_disk() before recovering queue_data, so disk_release() can tear down the owned queue. Also pair GenDisk::drop() with put_disk() after del_gendisk(). Once a Rust GenDisk has been added with device_add_disk(), del_gendisk() only unregisters it; the final gendisk reference still has to be dropped to complete the release path.

In the Linux kernel, the following vulnerability has been resolved: x86,fs/resctrl: Prevent out-of-bounds access while offlining CPU when SNC enabled The architecture updates the cpu_mask in a domain's header to track which online CPUs are associated with the domain. When this mask becomes empty the architecture initiates offline of the domain that includes calling on resctrl fs to offline the domain. If it is a monitoring domain in which LLC occupancy is tracked resctrl fs forces the limbo handler to clear all busy RMID state associated with the domain. The limbo handler always reads the current event value associated with a busy RMID irrespective of it being checked as part of regular "is it still busy" check or whether it will be forced released anyway. When reading an RMID on a system with SNC enabled the "logical RMID" is converted to the "physical RMID" and this conversion requires the NUMA node ID of the resctrl monitoring domain that is in turn determined by querying the NUMA node ID of any CPU belonging to the monitoring domain. When the monitoring domain is going offline its cpu_mask is empty causing the NUMA node ID query via cpu_to_node() to be done with "nr_cpu_ids" as argument resulting in an out-of-bounds access. Refactor the limbo handler to skip reading the RMID when the RMID will just be forced to no longer be dirty in the domain anyway. Add a safety check to the architecture's RMID reader to protect against this scenario.

In the Linux kernel, the following vulnerability has been resolved: netpoll: fix a use-after-free on shutdown path There is a use-after-free error on netpoll, which is clearly detected by KASAN. BUG: KASAN: slab-use-after-free in _raw_spin_lock_irqsave+0x3b/0x80 Read of size 1 at addr ... by task kworker/9:1 Workqueue: events queue_process Call Trace: skb_dequeue+0x1e/0xb0 queue_process+0x2c/0x600 process_scheduled_works+0x4b6/0x850 worker_thread+0x414/0x5a0 Allocated by task 242: __netpoll_setup+0x201/0x4a0 netpoll_setup+0x249/0x550 enabled_store+0x32f/0x380 Freed by task 0: kfree+0x1b7/0x540 rcu_core+0x3f8/0x7a0 The problem happens when there is a pending TX worker running in parallel with the cleanup path. This is what happens on netpoll shutdown path: 1) __netpoll_cleanup() is called 2) set dev->npinfo to NULL 3) call_rcu() with rcu_cleanup_netpoll_info() 3.1) rcu_cleanup_netpoll_info() tries to cancel all workers with cancel_delayed_work(), but doesn't wait for the worker to finish 4) and kfree(npinfo); Because 3.1) doesn't really cancel the work, as the comment says "we can't call cancel_delayed_work_sync here, as we are in softirq", the TX worker can run after 4). Tl;DR: queue_process() is not an RCU reader, it reaches npinfo through the work item via container_of(). Use disable_delayed_work_sync() to ensure the worker is completely stopped and prevent any future re-arming attempts. Once npinfo is set to NULL, senders will bail out and not queue new work. The disable flag ensures any in-flight re-arming attempts also fail silently. In the future, we can do the cleanup inline here without needing the npinfo->rcu rcu_head, but that is net-next material.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - fix VF2PF work teardown race in adf_disable_sriov() The VF2PF interrupt handler queues PF-side response work that stores a raw pointer to per-VF state (struct adf_accel_vf_info). Currently, adf_disable_sriov() destroys per-VF mutexes and frees vf_info without stopping new VF2PF work or waiting for in-flight workers to complete. A concurrently scheduled or already queued worker can then dereference freed memory. This manifests as a use-after-free when KASAN is enabled: BUG: KASAN: null-ptr-deref in mutex_lock+0x76/0xe0 Write of size 8 at addr 0000000000000260 by task kworker/24:2/... Workqueue: qat_pf2vf_resp_wq adf_iov_send_resp [intel_qat] Call Trace: kasan_report+0x119/0x140 mutex_lock+0x76/0xe0 adf_gen4_pfvf_send+0xd4/0x1f0 [intel_qat] adf_recv_and_handle_vf2pf_msg+0x290/0x360 [intel_qat] adf_iov_send_resp+0x8c/0xe0 [intel_qat] process_one_work+0x6ac/0xfd0 worker_thread+0x4dd/0xd30 kthread+0x326/0x410 ret_from_fork+0x33b/0x670 Add a PF-local flag, vf2pf_disabled, that gates work queueing, worker processing, and interrupt re-enabling during teardown. Set this flag atomically with the hardware interrupt mask inside adf_disable_all_vf2pf_interrupts(). After masking, synchronize the AE cluster MSI-X interrupt and flush the PF response workqueue before tearing down per-VF locks and state so all in-flight work completes before vf_info is destroyed. Introduce adf_enable_all_vf2pf_interrupts() to clear the flag and unmask all VF2PF interrupts under the same lock when SR-IOV is re-enabled. This ensures the software flag and hardware state transition atomically on both the enable and disable paths.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: Fix UAF in channel timeout by holding conn ref l2cap_chan_timeout() runs asynchronously and accesses chan->conn. If the connection is torn down while the timer is running or pending, chan->conn can be freed, leading to a use-after-free when the timer worker attempts to lock conn->lock: | BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:112 [inline] | BUG: KASAN: slab-use-after-free in atomic_long_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:4456 [inline] | BUG: KASAN: slab-use-after-free in __mutex_trylock_fast kernel/locking/mutex.c:161 [inline] | BUG: KASAN: slab-use-after-free in mutex_lock+0x4f/0xa0 kernel/locking/mutex.c:318 | Write of size 8 at addr ffff8881298d9550 by task kworker/2:1/83 | | CPU: 2 UID: 0 PID: 83 Comm: kworker/2:1 Not tainted 7.1.0-rc6-next-20260601-dirty #6 PREEMPT(full) | Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-debian-1.17.0-1 04/01/2014 | Workqueue: events l2cap_chan_timeout | Call Trace: | <TASK> | instrument_atomic_read_write include/linux/instrumented.h:112 [inline] | atomic_long_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:4456 [inline] | __mutex_trylock_fast kernel/locking/mutex.c:161 [inline] | mutex_lock+0x4f/0xa0 kernel/locking/mutex.c:318 | l2cap_chan_timeout+0x5d/0x1b0 net/bluetooth/l2cap_core.c:422 | process_one_work kernel/workqueue.c:3326 [inline] | process_scheduled_works+0x7c8/0xfb0 kernel/workqueue.c:3409 | worker_thread+0x8a9/0xcf0 kernel/workqueue.c:3490 | kthread+0x346/0x430 kernel/kthread.c:436 | ret_from_fork+0x1a3/0x470 arch/x86/kernel/process.c:158 | ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 | </TASK> | | Allocated by task 320: | l2cap_conn_add+0xa7/0x820 net/bluetooth/l2cap_core.c:7075 | l2cap_connect_cfm+0xdb/0xd70 net/bluetooth/l2cap_core.c:7452 | hci_connect_cfm include/net/bluetooth/hci_core.h:2139 [inline] | hci_remote_features_evt+0x52f/0x9f0 net/bluetooth/hci_event.c:3760 | hci_event_func net/bluetooth/hci_event.c:7796 [inline] | hci_event_packet+0x561/0xa70 net/bluetooth/hci_event.c:7847 | hci_rx_work+0x370/0x890 net/bluetooth/hci_core.c:4040 | process_one_work kernel/workqueue.c:3326 [inline] | process_scheduled_works+0x7c8/0xfb0 kernel/workqueue.c:3409 | worker_thread+0x8a9/0xcf0 kernel/workqueue.c:3490 | kthread+0x346/0x430 kernel/kthread.c:436 | ret_from_fork+0x1a3/0x470 arch/x86/kernel/process.c:158 | ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 | | Freed by task 322: | hci_disconn_cfm include/net/bluetooth/hci_core.h:2154 [inline] | hci_conn_hash_flush+0x101/0x1f0 net/bluetooth/hci_conn.c:2736 | hci_dev_close_sync+0x889/0xde0 net/bluetooth/hci_sync.c:5405 | hci_dev_do_close net/bluetooth/hci_core.c:502 [inline] | hci_unregister_dev+0x1f7/0x370 net/bluetooth/hci_core.c:2679 | vhci_release+0x12a/0x180 drivers/bluetooth/hci_vhci.c:690 | __fput+0x369/0x890 fs/file_table.c:510 | task_work_run+0x160/0x1d0 kernel/task_work.c:233 | get_signal+0xf5b/0x1120 kernel/signal.c:2810 | arch_do_signal_or_restart+0x4d/0x600 arch/x86/kernel/signal.c:337 | __exit_to_user_mode_loop kernel/entry/common.c:64 [inline] | exit_to_user_mode_loop+0x85/0x510 kernel/entry/common.c:98 | do_syscall_64+0x263/0x3d0 arch/x86/entry/syscall_64.c:100 | entry_SYSCALL_64_after_hwframe+0x77/0x7f | | The buggy address belongs to the object at ffff8881298d9400 | which belongs to the cache kmalloc-512 of size 512 | The buggy address is located 336 bytes inside of | freed 512-byte region [ffff8881298d9400, ffff8881298d9600) Fix it by having chan->conn hold a reference to l2cap_conn (via l2cap_conn_get) when the channel is added to the connection, and releasing it in the channel destructor. This ensures the l2cap_conn remains alive as long as the channel exists. A new FLAG_DEL channel flag is introduced to indicate that the ch ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ipv4: igmp: remove multicast group from hash table on device destruction When a device is destroyed under RTNL, ip_mc_destroy_dev() iterates through the multicast list and calls ip_ma_put() on each membership, scheduling them for RCU reclamation. However, they are not unlinked from the device's multicast hash table (mc_hash). Since the device remains published in dev->ip_ptr until after ip_mc_destroy_dev() completes, concurrent RCU readers traversing mc_hash can still locate and access the multicast group after its refcount is decremented. If the RCU callback runs and frees the group while a reader is accessing it, a use-after-free occurs. Fix this by unlinking the multicast group from mc_hash using ip_mc_hash_remove() before scheduling it for reclamation. BUG: KASAN: slab-use-after-free in ip_check_mc_rcu+0x149/0x3f0 Read of size 4 at addr ffff888009bf1408 by task mausezahn/2276 Call Trace: <IRQ> dump_stack_lvl+0x67/0x90 print_report+0x175/0x7c0 kasan_report+0x147/0x180 ip_check_mc_rcu+0x149/0x3f0 udp_v4_early_demux+0x36d/0x12d0 ip_rcv_finish_core+0xb8b/0x1390 ip_rcv_finish+0x54/0x120 NF_HOOK+0x213/0x2b0 __netif_receive_skb+0x126/0x340 process_backlog+0x4f2/0xf00 __napi_poll+0x92/0x2c0 net_rx_action+0x583/0xc60 handle_softirqs+0x236/0x7f0 do_softirq+0x57/0x80 </IRQ> Allocated by task 2239: kasan_save_track+0x3e/0x80 __kasan_kmalloc+0x72/0x90 ____ip_mc_inc_group+0x31a/0xa40 __ip_mc_join_group+0x334/0x3f0 do_ip_setsockopt+0x16fa/0x2010 ip_setsockopt+0x3f/0x90 do_sock_setsockopt+0x1ad/0x300 Freed by task 0: kasan_save_track+0x3e/0x80 kasan_save_free_info+0x40/0x50 __kasan_slab_free+0x3a/0x60 __rcu_free_sheaf_prepare+0xd4/0x220 rcu_free_sheaf+0x36/0x190 rcu_core+0x8d9/0x12f0 handle_softirqs+0x236/0x7f0

In the Linux kernel, the following vulnerability has been resolved: net: ipv4: bound TCP reordering sysctl writes and MTU probe sizes Reject invalid `net.ipv4.tcp_reordering` values before they reach TCP socket state. The sysctl is stored as an `int` but copied into the `u32` `tp->reordering` field for new sockets, so negative writes wrap to large values. With `tcp_mtu_probing=2`, the wrapped value can overflow the `tcp_mtu_probe()` size calculation and drive the MTU probing path into an out-of-bounds read. Route `tcp_reordering` writes through `proc_dointvec_minmax()` and require it to be at least 1. Also require `tcp_max_reordering` to be at least 1 so the configured maximum cannot become negative either. When registering the table for a non-init network namespace, relocate `extra2` pointers that refer into `init_net.ipv4` so the `tcp_reordering` upper bound follows that namespace's `tcp_max_reordering`. Harden `tcp_mtu_probe()` itself by computing `size_needed` as `u64`. This keeps the send queue and window checks from being bypassed through signed integer overflow.