CVE Feed

In the Linux kernel, the following vulnerability has been resolved: soc: mediatek: mtk-svs: Enable the IRQ later If the system does not come from reset (like when is booted via kexec()), the peripheral might triger an IRQ before the data structures are initialised. [ 0.227710] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000f08 [ 0.227913] Call trace: [ 0.227918] svs_isr+0x8c/0x538

In the Linux kernel, the following vulnerability has been resolved: tpm: Add !tpm_amd_is_rng_defective() to the hwrng_unregister() call site The following crash was reported: [ 1950.279393] list_del corruption, ffff99560d485790->next is NULL [ 1950.279400] ------------[ cut here ]------------ [ 1950.279401] kernel BUG at lib/list_debug.c:49! [ 1950.279405] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI [ 1950.279407] CPU: 11 PID: 5886 Comm: modprobe Tainted: G O 6.2.8_1 #1 [ 1950.279409] Hardware name: Gigabyte Technology Co., Ltd. B550M AORUS PRO-P/B550M AORUS PRO-P, BIOS F15c 05/11/2022 [ 1950.279410] RIP: 0010:__list_del_entry_valid+0x59/0xc0 [ 1950.279415] Code: 48 8b 01 48 39 f8 75 5a 48 8b 72 08 48 39 c6 75 65 b8 01 00 00 00 c3 cc cc cc cc 48 89 fe 48 c7 c7 08 a8 13 9e e8 b7 0a bc ff <0f> 0b 48 89 fe 48 c7 c7 38 a8 13 9e e8 a6 0a bc ff 0f 0b 48 89 fe [ 1950.279416] RSP: 0018:ffffa96d05647e08 EFLAGS: 00010246 [ 1950.279418] RAX: 0000000000000033 RBX: ffff99560d485750 RCX: 0000000000000000 [ 1950.279419] RDX: 0000000000000000 RSI: ffffffff9e107c59 RDI: 00000000ffffffff [ 1950.279420] RBP: ffffffffc19c5168 R08: 0000000000000000 R09: ffffa96d05647cc8 [ 1950.279421] R10: 0000000000000003 R11: ffffffff9ea2a568 R12: 0000000000000000 [ 1950.279422] R13: ffff99560140a2e0 R14: ffff99560127d2e0 R15: 0000000000000000 [ 1950.279422] FS: 00007f67da795380(0000) GS:ffff995d1f0c0000(0000) knlGS:0000000000000000 [ 1950.279424] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1950.279424] CR2: 00007f67da7e65c0 CR3: 00000001feed2000 CR4: 0000000000750ee0 [ 1950.279426] PKRU: 55555554 [ 1950.279426] Call Trace: [ 1950.279428] <TASK> [ 1950.279430] hwrng_unregister+0x28/0xe0 [rng_core] [ 1950.279436] tpm_chip_unregister+0xd5/0xf0 [tpm] Add the forgotten !tpm_amd_is_rng_defective() invariant to the hwrng_unregister() call site inside tpm_chip_unregister().

In the Linux kernel, the following vulnerability has been resolved: scsi: qedi: Fix use after free bug in qedi_remove() In qedi_probe() we call __qedi_probe() which initializes &qedi->recovery_work with qedi_recovery_handler() and &qedi->board_disable_work with qedi_board_disable_work(). When qedi_schedule_recovery_handler() is called, schedule_delayed_work() will finally start the work. In qedi_remove(), which is called to remove the driver, the following sequence may be observed: Fix this by finishing the work before cleanup in qedi_remove(). CPU0 CPU1 |qedi_recovery_handler qedi_remove | __qedi_remove | iscsi_host_free | scsi_host_put | //free shost | |iscsi_host_for_each_session |//use qedi->shost Cancel recovery_work and board_disable_work in __qedi_remove().

In the Linux kernel, the following vulnerability has been resolved: amdgpu/pm: prevent array underflow in vega20_odn_edit_dpm_table() In the PP_OD_EDIT_VDDC_CURVE case the "input_index" variable is capped at 2 but not checked for negative values so it results in an out of bounds read. This value comes from the user via sysfs.

In the Linux kernel, the following vulnerability has been resolved: fortify: Fix __compiletime_strlen() under UBSAN_BOUNDS_LOCAL With CONFIG_FORTIFY=y and CONFIG_UBSAN_LOCAL_BOUNDS=y enabled, we observe a runtime panic while running Android's Compatibility Test Suite's (CTS) android.hardware.input.cts.tests. This is stemming from a strlen() call in hidinput_allocate(). __compiletime_strlen() is implemented in terms of __builtin_object_size(), then does an array access to check for NUL-termination. A quirk of __builtin_object_size() is that for strings whose values are runtime dependent, __builtin_object_size(str, 1 or 0) returns the maximum size of possible values when those sizes are determinable at compile time. Example: static const char *v = "FOO BAR"; static const char *y = "FOO BA"; unsigned long x (int z) { // Returns 8, which is: // max(__builtin_object_size(v, 1), __builtin_object_size(y, 1)) return __builtin_object_size(z ? v : y, 1); } So when FORTIFY_SOURCE is enabled, the current implementation of __compiletime_strlen() will try to access beyond the end of y at runtime using the size of v. Mixed with UBSAN_LOCAL_BOUNDS we get a fault. hidinput_allocate() has a local C string whose value is control flow dependent on a switch statement, so __builtin_object_size(str, 1) evaluates to the maximum string length, making all other cases fault on the last character check. hidinput_allocate() could be cleaned up to avoid runtime calls to strlen() since the local variable can only have literal values, so there's no benefit to trying to fortify the strlen call site there. Perform a __builtin_constant_p() check against index 0 earlier in the macro to filter out the control-flow-dependant case. Add a KUnit test for checking the expected behavioral characteristics of FORTIFY_SOURCE internals.

In the Linux kernel, the following vulnerability has been resolved: net: phy: xgmiitorgmii: Fix refcount leak in xgmiitorgmii_probe of_phy_find_device() return device node with refcount incremented. Call put_device() to relese it when not needed anymore.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix refcount leak in hns_roce_mmap rdma_user_mmap_entry_get_pgoff() takes the reference. Add missing rdma_user_mmap_entry_put() to release the reference. Acked-by Haoyue Xu <[email protected]>

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - fix DMA transfer direction When CONFIG_DMA_API_DEBUG is selected, while running the crypto self test on the QAT crypto algorithms, the function add_dma_entry() reports a warning similar to the one below, saying that overlapping mappings are not supported. This occurs in tests where the input and the output scatter list point to the same buffers (i.e. two different scatter lists which point to the same chunks of memory). The logic that implements the mapping uses the flag DMA_BIDIRECTIONAL for both the input and the output scatter lists which leads to overlapped write mappings. These are not supported by the DMA layer. Fix by specifying the correct DMA transfer directions when mapping buffers. For in-place operations where the input scatter list matches the output scatter list, buffers are mapped once with DMA_BIDIRECTIONAL, otherwise input buffers are mapped using the flag DMA_TO_DEVICE and output buffers are mapped with DMA_FROM_DEVICE. Overlapping a read mapping with a write mapping is a valid case in dma-coherent devices like QAT. The function that frees and unmaps the buffers, qat_alg_free_bufl() has been changed accordingly to the changes to the mapping function. DMA-API: 4xxx 0000:06:00.0: cacheline tracking EEXIST, overlapping mappings aren't supported WARNING: CPU: 53 PID: 4362 at kernel/dma/debug.c:570 add_dma_entry+0x1e9/0x270 ... Call Trace: dma_map_page_attrs+0x82/0x2d0 ? preempt_count_add+0x6a/0xa0 qat_alg_sgl_to_bufl+0x45b/0x990 [intel_qat] qat_alg_aead_dec+0x71/0x250 [intel_qat] crypto_aead_decrypt+0x3d/0x70 test_aead_vec_cfg+0x649/0x810 ? number+0x310/0x3a0 ? vsnprintf+0x2a3/0x550 ? scnprintf+0x42/0x70 ? valid_sg_divisions.constprop.0+0x86/0xa0 ? test_aead_vec+0xdf/0x120 test_aead_vec+0xdf/0x120 alg_test_aead+0x185/0x400 alg_test+0x3d8/0x500 ? crypto_acomp_scomp_free_ctx+0x30/0x30 ? __schedule+0x32a/0x12a0 ? ttwu_queue_wakelist+0xbf/0x110 ? _raw_spin_unlock_irqrestore+0x23/0x40 ? try_to_wake_up+0x83/0x570 ? _raw_spin_unlock_irqrestore+0x23/0x40 ? __set_cpus_allowed_ptr_locked+0xea/0x1b0 ? crypto_acomp_scomp_free_ctx+0x30/0x30 cryptomgr_test+0x27/0x50 kthread+0xe6/0x110 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30

In the Linux kernel, the following vulnerability has been resolved: ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt I got a null-ptr-defer error report when I do the following tests on the qemu platform: make defconfig and CONFIG_PARPORT=m, CONFIG_PARPORT_PC=m, CONFIG_SND_MTS64=m Then making test scripts: cat>test_mod1.sh<<EOF modprobe snd-mts64 modprobe snd-mts64 EOF Executing the script, perhaps several times, we will get a null-ptr-defer report, as follow: syzkaller:~# ./test_mod.sh snd_mts64: probe of snd_mts64.0 failed with error -5 modprobe: ERROR: could not insert 'snd_mts64': No such device BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#1] PREEMPT SMP PTI CPU: 0 PID: 205 Comm: modprobe Not tainted 6.1.0-rc8-00588-g76dcd734eca2 #6 Call Trace: <IRQ> snd_mts64_interrupt+0x24/0xa0 [snd_mts64] parport_irq_handler+0x37/0x50 [parport] __handle_irq_event_percpu+0x39/0x190 handle_irq_event_percpu+0xa/0x30 handle_irq_event+0x2f/0x50 handle_edge_irq+0x99/0x1b0 __common_interrupt+0x5d/0x100 common_interrupt+0xa0/0xc0 </IRQ> <TASK> asm_common_interrupt+0x22/0x40 RIP: 0010:_raw_write_unlock_irqrestore+0x11/0x30 parport_claim+0xbd/0x230 [parport] snd_mts64_probe+0x14a/0x465 [snd_mts64] platform_probe+0x3f/0xa0 really_probe+0x129/0x2c0 __driver_probe_device+0x6d/0xc0 driver_probe_device+0x1a/0xa0 __device_attach_driver+0x7a/0xb0 bus_for_each_drv+0x62/0xb0 __device_attach+0xe4/0x180 bus_probe_device+0x82/0xa0 device_add+0x550/0x920 platform_device_add+0x106/0x220 snd_mts64_attach+0x2e/0x80 [snd_mts64] port_check+0x14/0x20 [parport] bus_for_each_dev+0x6e/0xc0 __parport_register_driver+0x7c/0xb0 [parport] snd_mts64_module_init+0x31/0x1000 [snd_mts64] do_one_initcall+0x3c/0x1f0 do_init_module+0x46/0x1c6 load_module+0x1d8d/0x1e10 __do_sys_finit_module+0xa2/0xf0 do_syscall_64+0x37/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd </TASK> Kernel panic - not syncing: Fatal exception in interrupt Rebooting in 1 seconds.. The mts wa not initialized during interrupt, we add check for mts to fix this bug.

In the Linux kernel, the following vulnerability has been resolved: netdevsim: fix memory leak in nsim_bus_dev_new() If device_register() failed in nsim_bus_dev_new(), the value of reference in nsim_bus_dev->dev is 1. obj->name in nsim_bus_dev->dev will not be released. unreferenced object 0xffff88810352c480 (size 16): comm "echo", pid 5691, jiffies 4294945921 (age 133.270s) hex dump (first 16 bytes): 6e 65 74 64 65 76 73 69 6d 31 00 00 00 00 00 00 netdevsim1...... backtrace: [<000000005e2e5e26>] __kmalloc_node_track_caller+0x3a/0xb0 [<0000000094ca4fc8>] kvasprintf+0xc3/0x160 [<00000000aad09bcc>] kvasprintf_const+0x55/0x180 [<000000009bac868d>] kobject_set_name_vargs+0x56/0x150 [<000000007c1a5d70>] dev_set_name+0xbb/0xf0 [<00000000ad0d126b>] device_add+0x1f8/0x1cb0 [<00000000c222ae24>] new_device_store+0x3b6/0x5e0 [<0000000043593421>] bus_attr_store+0x72/0xa0 [<00000000cbb1833a>] sysfs_kf_write+0x106/0x160 [<00000000d0dedb8a>] kernfs_fop_write_iter+0x3a8/0x5a0 [<00000000770b66e2>] vfs_write+0x8f0/0xc80 [<0000000078bb39be>] ksys_write+0x106/0x210 [<00000000005e55a4>] do_syscall_64+0x35/0x80 [<00000000eaa40bbc>] entry_SYSCALL_64_after_hwframe+0x46/0xb0

In the Linux kernel, the following vulnerability has been resolved: mmc: mxcmmc: fix return value check of mmc_add_host() mmc_add_host() may return error, if we ignore its return value, the memory that allocated in mmc_alloc_host() will be leaked and it will lead a kernel crash because of deleting not added device in the remove path. So fix this by checking the return value and goto error path which will call mmc_free_host().

In the Linux kernel, the following vulnerability has been resolved: fbdev: smscufx: Fix several use-after-free bugs Several types of UAFs can occur when physically removing a USB device. Adds ufx_ops_destroy() function to .fb_destroy of fb_ops, and in this function, there is kref_put() that finally calls ufx_free(). This fix prevents multiple UAFs.

In the Linux kernel, the following vulnerability has been resolved: crypto: marvell/octeontx - prevent integer overflows The "code_length" value comes from the firmware file. If your firmware is untrusted realistically there is probably very little you can do to protect yourself. Still we try to limit the damage as much as possible. Also Smatch marks any data read from the filesystem as untrusted and prints warnings if it not capped correctly. The "code_length * 2" can overflow. The round_up(ucode_size, 16) + sizeof() expression can overflow too. Prevent these overflows.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Avoid UBSAN error on true_sectors_per_clst() syzbot reported UBSAN error as below: [ 76.901829][ T6677] ================================================================================ [ 76.903908][ T6677] UBSAN: shift-out-of-bounds in fs/ntfs3/super.c:675:13 [ 76.905363][ T6677] shift exponent -247 is negative This patch avoid this error.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix PCI device refcount leak in amdgpu_atrm_get_bios() As comment of pci_get_class() says, it returns a pci_device with its refcount increased and decreased the refcount for the input parameter @from if it is not NULL. If we break the loop in amdgpu_atrm_get_bios() with 'pdev' not NULL, we need to call pci_dev_put() to decrease the refcount. Add the missing pci_dev_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: media: camss: Clean up received buffers on failed start of streaming It is required to return the received buffers, if streaming can not be started. For instance media_pipeline_start() may fail with EPIPE, if a link validation between entities is not passed, and in such a case a user gets a kernel warning: WARNING: CPU: 1 PID: 520 at drivers/media/common/videobuf2/videobuf2-core.c:1592 vb2_start_streaming+0xec/0x160 <snip> Call trace: vb2_start_streaming+0xec/0x160 vb2_core_streamon+0x9c/0x1a0 vb2_ioctl_streamon+0x68/0xbc v4l_streamon+0x30/0x3c __video_do_ioctl+0x184/0x3e0 video_usercopy+0x37c/0x7b0 video_ioctl2+0x24/0x40 v4l2_ioctl+0x4c/0x70 The fix is to correct the error path in video_start_streaming() of camss.

In the Linux kernel, the following vulnerability has been resolved: udf: Avoid double brelse() in udf_rename() syzbot reported a warning like below [1]: VFS: brelse: Trying to free free buffer WARNING: CPU: 2 PID: 7301 at fs/buffer.c:1145 __brelse+0x67/0xa0 ... Call Trace: <TASK> invalidate_bh_lru+0x99/0x150 smp_call_function_many_cond+0xe2a/0x10c0 ? generic_remap_file_range_prep+0x50/0x50 ? __brelse+0xa0/0xa0 ? __mutex_lock+0x21c/0x12d0 ? smp_call_on_cpu+0x250/0x250 ? rcu_read_lock_sched_held+0xb/0x60 ? lock_release+0x587/0x810 ? __brelse+0xa0/0xa0 ? generic_remap_file_range_prep+0x50/0x50 on_each_cpu_cond_mask+0x3c/0x80 blkdev_flush_mapping+0x13a/0x2f0 blkdev_put_whole+0xd3/0xf0 blkdev_put+0x222/0x760 deactivate_locked_super+0x96/0x160 deactivate_super+0xda/0x100 cleanup_mnt+0x222/0x3d0 task_work_run+0x149/0x240 ? task_work_cancel+0x30/0x30 do_exit+0xb29/0x2a40 ? reacquire_held_locks+0x4a0/0x4a0 ? do_raw_spin_lock+0x12a/0x2b0 ? mm_update_next_owner+0x7c0/0x7c0 ? rwlock_bug.part.0+0x90/0x90 ? zap_other_threads+0x234/0x2d0 do_group_exit+0xd0/0x2a0 __x64_sys_exit_group+0x3a/0x50 do_syscall_64+0x34/0xb0 entry_SYSCALL_64_after_hwframe+0x63/0xcd The cause of the issue is that brelse() is called on both ofibh.sbh and ofibh.ebh by udf_find_entry() when it returns NULL. However, brelse() is called by udf_rename(), too. So, b_count on buffer_head becomes unbalanced. This patch fixes the issue by not calling brelse() by udf_rename() when udf_find_entry() returns NULL.

In the Linux kernel, the following vulnerability has been resolved: apparmor: fix a memleak in multi_transaction_new() In multi_transaction_new(), the variable t is not freed or passed out on the failure of copy_from_user(t->data, buf, size), which could lead to a memleak. Fix this bug by adding a put_multi_transaction(t) in the error path.

In the Linux kernel, the following vulnerability has been resolved: md/raid5: Remove unnecessary bio_put() in raid5_read_one_chunk() When running chunk-sized reads on disks with badblocks duplicate bio free/puts are observed: ============================================================================= BUG bio-200 (Not tainted): Object already free ----------------------------------------------------------------------------- Allocated in mempool_alloc_slab+0x17/0x20 age=3 cpu=2 pid=7504 __slab_alloc.constprop.0+0x5a/0xb0 kmem_cache_alloc+0x31e/0x330 mempool_alloc_slab+0x17/0x20 mempool_alloc+0x100/0x2b0 bio_alloc_bioset+0x181/0x460 do_mpage_readpage+0x776/0xd00 mpage_readahead+0x166/0x320 blkdev_readahead+0x15/0x20 read_pages+0x13f/0x5f0 page_cache_ra_unbounded+0x18d/0x220 force_page_cache_ra+0x181/0x1c0 page_cache_sync_ra+0x65/0xb0 filemap_get_pages+0x1df/0xaf0 filemap_read+0x1e1/0x700 blkdev_read_iter+0x1e5/0x330 vfs_read+0x42a/0x570 Freed in mempool_free_slab+0x17/0x20 age=3 cpu=2 pid=7504 kmem_cache_free+0x46d/0x490 mempool_free_slab+0x17/0x20 mempool_free+0x66/0x190 bio_free+0x78/0x90 bio_put+0x100/0x1a0 raid5_make_request+0x2259/0x2450 md_handle_request+0x402/0x600 md_submit_bio+0xd9/0x120 __submit_bio+0x11f/0x1b0 submit_bio_noacct_nocheck+0x204/0x480 submit_bio_noacct+0x32e/0xc70 submit_bio+0x98/0x1a0 mpage_readahead+0x250/0x320 blkdev_readahead+0x15/0x20 read_pages+0x13f/0x5f0 page_cache_ra_unbounded+0x18d/0x220 Slab 0xffffea000481b600 objects=21 used=0 fp=0xffff8881206d8940 flags=0x17ffffc0010201(locked|slab|head|node=0|zone=2|lastcpupid=0x1fffff) CPU: 0 PID: 34525 Comm: kworker/u24:2 Not tainted 6.0.0-rc2-localyes-265166-gf11c5343fa3f #143 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-1ubuntu1.1 04/01/2014 Workqueue: raid5wq raid5_do_work Call Trace: <TASK> dump_stack_lvl+0x5a/0x78 dump_stack+0x10/0x16 print_trailer+0x158/0x165 object_err+0x35/0x50 free_debug_processing.cold+0xb7/0xbe __slab_free+0x1ae/0x330 kmem_cache_free+0x46d/0x490 mempool_free_slab+0x17/0x20 mempool_free+0x66/0x190 bio_free+0x78/0x90 bio_put+0x100/0x1a0 mpage_end_io+0x36/0x150 bio_endio+0x2fd/0x360 md_end_io_acct+0x7e/0x90 bio_endio+0x2fd/0x360 handle_failed_stripe+0x960/0xb80 handle_stripe+0x1348/0x3760 handle_active_stripes.constprop.0+0x72a/0xaf0 raid5_do_work+0x177/0x330 process_one_work+0x616/0xb20 worker_thread+0x2bd/0x6f0 kthread+0x179/0x1b0 ret_from_fork+0x22/0x30 </TASK> The double free is caused by an unnecessary bio_put() in the if(is_badblock(...)) error path in raid5_read_one_chunk(). The error path was moved ahead of bio_alloc_clone() in c82aa1b76787c ("md/raid5: move checking badblock before clone bio in raid5_read_one_chunk"). The previous code checked and freed align_bio which required a bio_put. After the move that is no longer needed as raid_bio is returned to the control of the common io path which performs its own endio resulting in a double free on bad device blocks.

In the Linux kernel, the following vulnerability has been resolved: acct: fix potential integer overflow in encode_comp_t() The integer overflow is descripted with following codes: > 317 static comp_t encode_comp_t(u64 value) > 318 { > 319 int exp, rnd; ...... > 341 exp <<= MANTSIZE; > 342 exp += value; > 343 return exp; > 344 } Currently comp_t is defined as type of '__u16', but the variable 'exp' is type of 'int', so overflow would happen when variable 'exp' in line 343 is greater than 65535.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Validate index root when initialize NTFS security This enhances the sanity check for $SDH and $SII while initializing NTFS security, guarantees these index root are legit. [ 162.459513] BUG: KASAN: use-after-free in hdr_find_e.isra.0+0x10c/0x320 [ 162.460176] Read of size 2 at addr ffff8880037bca99 by task mount/243 [ 162.460851] [ 162.461252] CPU: 0 PID: 243 Comm: mount Not tainted 6.0.0-rc7 #42 [ 162.461744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 162.462609] Call Trace: [ 162.462954] <TASK> [ 162.463276] dump_stack_lvl+0x49/0x63 [ 162.463822] print_report.cold+0xf5/0x689 [ 162.464608] ? unwind_get_return_address+0x3a/0x60 [ 162.465766] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.466975] kasan_report+0xa7/0x130 [ 162.467506] ? _raw_spin_lock_irq+0xc0/0xf0 [ 162.467998] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.468536] __asan_load2+0x68/0x90 [ 162.468923] hdr_find_e.isra.0+0x10c/0x320 [ 162.469282] ? cmp_uints+0xe0/0xe0 [ 162.469557] ? cmp_sdh+0x90/0x90 [ 162.469864] ? ni_find_attr+0x214/0x300 [ 162.470217] ? ni_load_mi+0x80/0x80 [ 162.470479] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.470931] ? ntfs_bread_run+0x190/0x190 [ 162.471307] ? indx_get_root+0xe4/0x190 [ 162.471556] ? indx_get_root+0x140/0x190 [ 162.471833] ? indx_init+0x1e0/0x1e0 [ 162.472069] ? fnd_clear+0x115/0x140 [ 162.472363] ? _raw_spin_lock_irqsave+0x100/0x100 [ 162.472731] indx_find+0x184/0x470 [ 162.473461] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ 162.474429] ? indx_find_buffer+0x2d0/0x2d0 [ 162.474704] ? do_syscall_64+0x3b/0x90 [ 162.474962] dir_search_u+0x196/0x2f0 [ 162.475381] ? ntfs_nls_to_utf16+0x450/0x450 [ 162.475661] ? ntfs_security_init+0x3d6/0x440 [ 162.475906] ? is_sd_valid+0x180/0x180 [ 162.476191] ntfs_extend_init+0x13f/0x2c0 [ 162.476496] ? ntfs_fix_post_read+0x130/0x130 [ 162.476861] ? iput.part.0+0x286/0x320 [ 162.477325] ntfs_fill_super+0x11e0/0x1b50 [ 162.477709] ? put_ntfs+0x1d0/0x1d0 [ 162.477970] ? vsprintf+0x20/0x20 [ 162.478258] ? set_blocksize+0x95/0x150 [ 162.478538] get_tree_bdev+0x232/0x370 [ 162.478789] ? put_ntfs+0x1d0/0x1d0 [ 162.479038] ntfs_fs_get_tree+0x15/0x20 [ 162.479374] vfs_get_tree+0x4c/0x130 [ 162.479729] path_mount+0x654/0xfe0 [ 162.480124] ? putname+0x80/0xa0 [ 162.480484] ? finish_automount+0x2e0/0x2e0 [ 162.480894] ? putname+0x80/0xa0 [ 162.481467] ? kmem_cache_free+0x1c4/0x440 [ 162.482280] ? putname+0x80/0xa0 [ 162.482714] do_mount+0xd6/0xf0 [ 162.483264] ? path_mount+0xfe0/0xfe0 [ 162.484782] ? __kasan_check_write+0x14/0x20 [ 162.485593] __x64_sys_mount+0xca/0x110 [ 162.486024] do_syscall_64+0x3b/0x90 [ 162.486543] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.487141] RIP: 0033:0x7f9d374e948a [ 162.488324] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 162.489728] RSP: 002b:00007ffe30e73d18 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5 [ 162.490971] RAX: ffffffffffffffda RBX: 0000561cdb43a060 RCX: 00007f9d374e948a [ 162.491669] RDX: 0000561cdb43a260 RSI: 0000561cdb43a2e0 RDI: 0000561cdb442af0 [ 162.492050] RBP: 0000000000000000 R08: 0000561cdb43a280 R09: 0000000000000020 [ 162.492459] R10: 00000000c0ed0000 R11: 0000000000000206 R12: 0000561cdb442af0 [ 162.493183] R13: 0000561cdb43a260 R14: 0000000000000000 R15: 00000000ffffffff [ 162.493644] </TASK> [ 162.493908] [ 162.494214] The buggy address belongs to the physical page: [ 162.494761] page:000000003e38a3d5 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x37bc [ 162.496064] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) [ 162.497278] raw: 000fffffc0000000 ffffea00000df1c8 ffffea00000df008 0000000000000000 [ 162.498928] raw: 0000000000000000 0000000000240000 0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: RDMA/siw: Fix immediate work request flush to completion queue Correctly set send queue element opcode during immediate work request flushing in post sendqueue operation, if the QP is in ERROR state. An undefined ocode value results in out-of-bounds access to an array for mapping the opcode between siw internal and RDMA core representation in work completion generation. It resulted in a KASAN BUG report of type 'global-out-of-bounds' during NFSoRDMA testing. This patch further fixes a potential case of a malicious user which may write undefined values for completion queue elements status or opcode, if the CQ is memory mapped to user land. It avoids the same out-of-bounds access to arrays for status and opcode mapping as described above.

In the Linux kernel, the following vulnerability has been resolved: vhost-vdpa: fix an iotlb memory leak Before commit 3d5698793897 ("vhost-vdpa: introduce asid based IOTLB") we called vhost_vdpa_iotlb_unmap(v, iotlb, 0ULL, 0ULL - 1) during release to free all the resources allocated when processing user IOTLB messages through vhost_vdpa_process_iotlb_update(). That commit changed the handling of IOTLB a bit, and we accidentally removed some code called during the release. We partially fixed this with commit 037d4305569a ("vhost-vdpa: call vhost_vdpa_cleanup during the release") but a potential memory leak is still there as showed by kmemleak if the application does not send VHOST_IOTLB_INVALIDATE or crashes: unreferenced object 0xffff888007fbaa30 (size 16): comm "blkio-bench", pid 914, jiffies 4294993521 (age 885.500s) hex dump (first 16 bytes): 40 73 41 07 80 88 ff ff 00 00 00 00 00 00 00 00 @sA............. backtrace: [<0000000087736d2a>] kmem_cache_alloc_trace+0x142/0x1c0 [<0000000060740f50>] vhost_vdpa_process_iotlb_msg+0x68c/0x901 [vhost_vdpa] [<0000000083e8e205>] vhost_chr_write_iter+0xc0/0x4a0 [vhost] [<000000008f2f414a>] vhost_vdpa_chr_write_iter+0x18/0x20 [vhost_vdpa] [<00000000de1cd4a0>] vfs_write+0x216/0x4b0 [<00000000a2850200>] ksys_write+0x71/0xf0 [<00000000de8e720b>] __x64_sys_write+0x19/0x20 [<0000000018b12cbb>] do_syscall_64+0x3f/0x90 [<00000000986ec465>] entry_SYSCALL_64_after_hwframe+0x63/0xcd Let's fix this calling vhost_vdpa_iotlb_unmap() on the whole range in vhost_vdpa_remove_as(). We move that call before vhost_dev_cleanup() since we need a valid v->vdev.mm in vhost_vdpa_pa_unmap(). vhost_iotlb_reset() call can be removed, since vhost_vdpa_iotlb_unmap() on the whole range removes all the entries. The kmemleak log reported was observed with a vDPA device that has `use_va` set to true (e.g. VDUSE). This patch has been tested with both types of devices.

In the Linux kernel, the following vulnerability has been resolved: ext4: silence the warning when evicting inode with dioread_nolock When evicting an inode with default dioread_nolock, it could be raced by the unwritten extents converting kworker after writeback some new allocated dirty blocks. It convert unwritten extents to written, the extents could be merged to upper level and free extent blocks, so it could mark the inode dirty again even this inode has been marked I_FREEING. But the inode->i_io_list check and warning in ext4_evict_inode() missing this corner case. Fortunately, ext4_evict_inode() will wait all extents converting finished before this check, so it will not lead to inode use-after-free problem, every thing is OK besides this warning. The WARN_ON_ONCE was originally designed for finding inode use-after-free issues in advance, but if we add current dioread_nolock case in, it will become not quite useful, so fix this warning by just remove this check. ====== WARNING: CPU: 7 PID: 1092 at fs/ext4/inode.c:227 ext4_evict_inode+0x875/0xc60 ... RIP: 0010:ext4_evict_inode+0x875/0xc60 ... Call Trace: <TASK> evict+0x11c/0x2b0 iput+0x236/0x3a0 do_unlinkat+0x1b4/0x490 __x64_sys_unlinkat+0x4c/0xb0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7fa933c1115b ====== rm kworker ext4_end_io_end() vfs_unlink() ext4_unlink() ext4_convert_unwritten_io_end_vec() ext4_convert_unwritten_extents() ext4_map_blocks() ext4_ext_map_blocks() ext4_ext_try_to_merge_up() __mark_inode_dirty() check !I_FREEING locked_inode_to_wb_and_lock_list() iput() iput_final() evict() ext4_evict_inode() truncate_inode_pages_final() //wait release io_end inode_io_list_move_locked() ext4_release_io_end() trigger WARN_ON_ONCE()

In the Linux kernel, the following vulnerability has been resolved: media: vidtv: Fix use-after-free in vidtv_bridge_dvb_init() KASAN reports a use-after-free: BUG: KASAN: use-after-free in dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core] Call Trace: ... dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core] vidtv_bridge_probe+0x7bf/0xa40 [dvb_vidtv_bridge] platform_probe+0xb6/0x170 ... Allocated by task 1238: ... dvb_register_device+0x1a7/0xa70 [dvb_core] dvb_dmxdev_init+0x2af/0x4a0 [dvb_core] vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge] ... Freed by task 1238: dvb_register_device+0x6d2/0xa70 [dvb_core] dvb_dmxdev_init+0x2af/0x4a0 [dvb_core] vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge] ... It is because the error handling in vidtv_bridge_dvb_init() is wrong. First, vidtv_bridge_dmx(dev)_init() will clean themselves when fail, but goto fail_dmx(_dev): calls release functions again, which causes use-after-free. Also, in fail_fe, fail_tuner_probe and fail_demod_probe, j = i will cause out-of-bound when i finished its loop (i == NUM_FE). And the loop releasing is wrong, although now NUM_FE is 1 so it won't cause problem. Fix this by correctly releasing everything.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix pci device refcount leak As comment of pci_get_domain_bus_and_slot() says, it returns a pci device with refcount increment, when finish using it, the caller must decrement the reference count by calling pci_dev_put(). So before returning from amdgpu_device_resume|suspend_display_audio(), pci_dev_put() is called to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: wifi: ar5523: Fix use-after-free on ar5523_cmd() timed out syzkaller reported use-after-free with the stack trace like below [1]: [ 38.960489][ C3] ================================================================== [ 38.963216][ C3] BUG: KASAN: use-after-free in ar5523_cmd_tx_cb+0x220/0x240 [ 38.964950][ C3] Read of size 8 at addr ffff888048e03450 by task swapper/3/0 [ 38.966363][ C3] [ 38.967053][ C3] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.0.0-09039-ga6afa4199d3d-dirty #18 [ 38.968464][ C3] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014 [ 38.969959][ C3] Call Trace: [ 38.970841][ C3] <IRQ> [ 38.971663][ C3] dump_stack_lvl+0xfc/0x174 [ 38.972620][ C3] print_report.cold+0x2c3/0x752 [ 38.973626][ C3] ? ar5523_cmd_tx_cb+0x220/0x240 [ 38.974644][ C3] kasan_report+0xb1/0x1d0 [ 38.975720][ C3] ? ar5523_cmd_tx_cb+0x220/0x240 [ 38.976831][ C3] ar5523_cmd_tx_cb+0x220/0x240 [ 38.978412][ C3] __usb_hcd_giveback_urb+0x353/0x5b0 [ 38.979755][ C3] usb_hcd_giveback_urb+0x385/0x430 [ 38.981266][ C3] dummy_timer+0x140c/0x34e0 [ 38.982925][ C3] ? notifier_call_chain+0xb5/0x1e0 [ 38.984761][ C3] ? rcu_read_lock_sched_held+0xb/0x60 [ 38.986242][ C3] ? lock_release+0x51c/0x790 [ 38.987323][ C3] ? _raw_read_unlock_irqrestore+0x37/0x70 [ 38.988483][ C3] ? __wake_up_common_lock+0xde/0x130 [ 38.989621][ C3] ? reacquire_held_locks+0x4a0/0x4a0 [ 38.990777][ C3] ? lock_acquire+0x472/0x550 [ 38.991919][ C3] ? rcu_read_lock_sched_held+0xb/0x60 [ 38.993138][ C3] ? lock_acquire+0x472/0x550 [ 38.994890][ C3] ? dummy_urb_enqueue+0x860/0x860 [ 38.996266][ C3] ? do_raw_spin_unlock+0x16f/0x230 [ 38.997670][ C3] ? dummy_urb_enqueue+0x860/0x860 [ 38.999116][ C3] call_timer_fn+0x1a0/0x6a0 [ 39.000668][ C3] ? add_timer_on+0x4a0/0x4a0 [ 39.002137][ C3] ? reacquire_held_locks+0x4a0/0x4a0 [ 39.003809][ C3] ? __next_timer_interrupt+0x226/0x2a0 [ 39.005509][ C3] __run_timers.part.0+0x69a/0xac0 [ 39.007025][ C3] ? dummy_urb_enqueue+0x860/0x860 [ 39.008716][ C3] ? call_timer_fn+0x6a0/0x6a0 [ 39.010254][ C3] ? cpuacct_percpu_seq_show+0x10/0x10 [ 39.011795][ C3] ? kvm_sched_clock_read+0x14/0x40 [ 39.013277][ C3] ? sched_clock_cpu+0x69/0x2b0 [ 39.014724][ C3] run_timer_softirq+0xb6/0x1d0 [ 39.016196][ C3] __do_softirq+0x1d2/0x9be [ 39.017616][ C3] __irq_exit_rcu+0xeb/0x190 [ 39.019004][ C3] irq_exit_rcu+0x5/0x20 [ 39.020361][ C3] sysvec_apic_timer_interrupt+0x8f/0xb0 [ 39.021965][ C3] </IRQ> [ 39.023237][ C3] <TASK> In ar5523_probe(), ar5523_host_available() calls ar5523_cmd() as below (there are other functions which finally call ar5523_cmd()): ar5523_probe() -> ar5523_host_available() -> ar5523_cmd_read() -> ar5523_cmd() If ar5523_cmd() timed out, then ar5523_host_available() failed and ar5523_probe() freed the device structure. So, ar5523_cmd_tx_cb() might touch the freed structure. This patch fixes this issue by canceling in-flight tx cmd if submitted urb timed out.

In the Linux kernel, the following vulnerability has been resolved: md/raid1: stop mdx_raid1 thread when raid1 array run failed fail run raid1 array when we assemble array with the inactive disk only, but the mdx_raid1 thread were not stop, Even if the associated resources have been released. it will caused a NULL dereference when we do poweroff. This causes the following Oops: [ 287.587787] BUG: kernel NULL pointer dereference, address: 0000000000000070 [ 287.594762] #PF: supervisor read access in kernel mode [ 287.599912] #PF: error_code(0x0000) - not-present page [ 287.605061] PGD 0 P4D 0 [ 287.607612] Oops: 0000 [#1] SMP NOPTI [ 287.611287] CPU: 3 PID: 5265 Comm: md0_raid1 Tainted: G U 5.10.146 #0 [ 287.619029] Hardware name: xxxxxxx/To be filled by O.E.M, BIOS 5.19 06/16/2022 [ 287.626775] RIP: 0010:md_check_recovery+0x57/0x500 [md_mod] [ 287.632357] Code: fe 01 00 00 48 83 bb 10 03 00 00 00 74 08 48 89 ...... [ 287.651118] RSP: 0018:ffffc90000433d78 EFLAGS: 00010202 [ 287.656347] RAX: 0000000000000000 RBX: ffff888105986800 RCX: 0000000000000000 [ 287.663491] RDX: ffffc90000433bb0 RSI: 00000000ffffefff RDI: ffff888105986800 [ 287.670634] RBP: ffffc90000433da0 R08: 0000000000000000 R09: c0000000ffffefff [ 287.677771] R10: 0000000000000001 R11: ffffc90000433ba8 R12: ffff888105986800 [ 287.684907] R13: 0000000000000000 R14: fffffffffffffe00 R15: ffff888100b6b500 [ 287.692052] FS: 0000000000000000(0000) GS:ffff888277f80000(0000) knlGS:0000000000000000 [ 287.700149] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 287.705897] CR2: 0000000000000070 CR3: 000000000320a000 CR4: 0000000000350ee0 [ 287.713033] Call Trace: [ 287.715498] raid1d+0x6c/0xbbb [raid1] [ 287.719256] ? __schedule+0x1ff/0x760 [ 287.722930] ? schedule+0x3b/0xb0 [ 287.726260] ? schedule_timeout+0x1ed/0x290 [ 287.730456] ? __switch_to+0x11f/0x400 [ 287.734219] md_thread+0xe9/0x140 [md_mod] [ 287.738328] ? md_thread+0xe9/0x140 [md_mod] [ 287.742601] ? wait_woken+0x80/0x80 [ 287.746097] ? md_register_thread+0xe0/0xe0 [md_mod] [ 287.751064] kthread+0x11a/0x140 [ 287.754300] ? kthread_park+0x90/0x90 [ 287.757974] ret_from_fork+0x1f/0x30 In fact, when raid1 array run fail, we need to do md_unregister_thread() before raid1_free().

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921e: fix rmmod crash in driver reload test In insmod/rmmod stress test, the following crash dump shows up immediately. The problem is caused by missing mt76_dev in mt7921_pci_remove(). We should make sure the drvdata is ready before probe() finished. [168.862789] ================================================================== [168.862797] BUG: KASAN: user-memory-access in try_to_grab_pending+0x59/0x480 [168.862805] Write of size 8 at addr 0000000000006df0 by task rmmod/5361 [168.862812] CPU: 7 PID: 5361 Comm: rmmod Tainted: G OE 5.19.0-rc6 #1 [168.862816] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, 05/04/2020 [168.862820] Call Trace: [168.862822] <TASK> [168.862825] dump_stack_lvl+0x49/0x63 [168.862832] print_report.cold+0x493/0x6b7 [168.862845] kasan_report+0xa7/0x120 [168.862857] kasan_check_range+0x163/0x200 [168.862861] __kasan_check_write+0x14/0x20 [168.862866] try_to_grab_pending+0x59/0x480 [168.862870] __cancel_work_timer+0xbb/0x340 [168.862898] cancel_work_sync+0x10/0x20 [168.862902] mt7921_pci_remove+0x61/0x1c0 [mt7921e] [168.862909] pci_device_remove+0xa3/0x1d0 [168.862914] device_remove+0xc4/0x170 [168.862920] device_release_driver_internal+0x163/0x300 [168.862925] driver_detach+0xc7/0x1a0 [168.862930] bus_remove_driver+0xeb/0x2d0 [168.862935] driver_unregister+0x71/0xb0 [168.862939] pci_unregister_driver+0x30/0x230 [168.862944] mt7921_pci_driver_exit+0x10/0x1b [mt7921e] [168.862949] __x64_sys_delete_module+0x2f9/0x4b0 [168.862968] do_syscall_64+0x38/0x90 [168.862973] entry_SYSCALL_64_after_hwframe+0x63/0xcd Test steps: 1. insmode 2. do not ifup 3. rmmod quickly (within 1 second)

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Fix an integer overflow in aie2_query_ctx_status_array() The unpublished smatch static checker reported a warning. drivers/accel/amdxdna/aie2_pci.c:904 aie2_query_ctx_status_array() warn: potential user controlled sizeof overflow 'args->num_element * args->element_size' '1-u32max(user) * 1-u32max(user)' Even this will not cause a real issue, it is better to put a reasonable limitation for element_size and num_element. Add condition to make sure the input element_size <= 4K and num_element <= 1K.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix stackmap overflow check in __bpf_get_stackid() Syzkaller reported a KASAN slab-out-of-bounds write in __bpf_get_stackid() when copying stack trace data. The issue occurs when the perf trace contains more stack entries than the stack map bucket can hold, leading to an out-of-bounds write in the bucket's data array.

In the Linux kernel, the following vulnerability has been resolved: perf/x86: Fix NULL event access and potential PEBS record loss When intel_pmu_drain_pebs_icl() is called to drain PEBS records, the perf_event_overflow() could be called to process the last PEBS record. While perf_event_overflow() could trigger the interrupt throttle and stop all events of the group, like what the below call-chain shows. perf_event_overflow() -> __perf_event_overflow() ->__perf_event_account_interrupt() -> perf_event_throttle_group() -> perf_event_throttle() -> event->pmu->stop() -> x86_pmu_stop() The side effect of stopping the events is that all corresponding event pointers in cpuc->events[] array are cleared to NULL. Assume there are two PEBS events (event a and event b) in a group. When intel_pmu_drain_pebs_icl() calls perf_event_overflow() to process the last PEBS record of PEBS event a, interrupt throttle is triggered and all pointers of event a and event b are cleared to NULL. Then intel_pmu_drain_pebs_icl() tries to process the last PEBS record of event b and encounters NULL pointer access. To avoid this issue, move cpuc->events[] clearing from x86_pmu_stop() to x86_pmu_del(). It's safe since cpuc->active_mask or cpuc->pebs_enabled is always checked before access the event pointer from cpuc->events[].

In the Linux kernel, the following vulnerability has been resolved: md: fix rcu protection in md_wakeup_thread We attempted to use RCU to protect the pointer 'thread', but directly passed the value when calling md_wakeup_thread(). This means that the RCU pointer has been acquired before rcu_read_lock(), which renders rcu_read_lock() ineffective and could lead to a use-after-free.

In the Linux kernel, the following vulnerability has been resolved: md: avoid repeated calls to del_gendisk There is a uaf problem which is found by case 23rdev-lifetime: Oops: general protection fault, probably for non-canonical address 0xdead000000000122 RIP: 0010:bdi_unregister+0x4b/0x170 Call Trace: <TASK> __del_gendisk+0x356/0x3e0 mddev_unlock+0x351/0x360 rdev_attr_store+0x217/0x280 kernfs_fop_write_iter+0x14a/0x210 vfs_write+0x29e/0x550 ksys_write+0x74/0xf0 do_syscall_64+0xbb/0x380 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7ff5250a177e The sequence is: 1. rdev remove path gets reconfig_mutex 2. rdev remove path release reconfig_mutex in mddev_unlock 3. md stop calls do_md_stop and sets MD_DELETED 4. rdev remove path calls del_gendisk because MD_DELETED is set 5. md stop path release reconfig_mutex and calls del_gendisk again So there is a race condition we should resolve. This patch adds a flag MD_DO_DELETE to avoid the race condition.

In the Linux kernel, the following vulnerability has been resolved: coresight: tmc: add the handle of the event to the path The handle is essential for retrieving the AUX_EVENT of each CPU and is required in perf mode. It has been added to the coresight_path so that dependent devices can access it from the path when needed. The existing bug can be reproduced with: perf record -e cs_etm//k -C 0-9 dd if=/dev/zero of=/dev/null Showing an oops as follows: Unable to handle kernel paging request at virtual address 000f6e84934ed19e Call trace: tmc_etr_get_buffer+0x30/0x80 [coresight_tmc] (P) catu_enable_hw+0xbc/0x3d0 [coresight_catu] catu_enable+0x70/0xe0 [coresight_catu] coresight_enable_path+0xb0/0x258 [coresight]

In the Linux kernel, the following vulnerability has been resolved: ocfs2: relax BUG() to ocfs2_error() in __ocfs2_move_extent() In '__ocfs2_move_extent()', relax 'BUG()' to 'ocfs2_error()' just to avoid crashing the whole kernel due to a filesystem corruption.

In the Linux kernel, the following vulnerability has been resolved: bpf: Check skb->transport_header is set in bpf_skb_check_mtu The bpf_skb_check_mtu helper needs to use skb->transport_header when the BPF_MTU_CHK_SEGS flag is used: bpf_skb_check_mtu(skb, ifindex, &mtu_len, 0, BPF_MTU_CHK_SEGS) The transport_header is not always set. There is a WARN_ON_ONCE report when CONFIG_DEBUG_NET is enabled + skb->gso_size is set + bpf_prog_test_run is used: WARNING: CPU: 1 PID: 2216 at ./include/linux/skbuff.h:3071 skb_gso_validate_network_len bpf_skb_check_mtu bpf_prog_3920e25740a41171_tc_chk_segs_flag # A test in the next patch bpf_test_run bpf_prog_test_run_skb For a normal ingress skb (not test_run), skb_reset_transport_header is performed but there is plan to avoid setting it as described in commit 2170a1f09148 ("net: no longer reset transport_header in __netif_receive_skb_core()"). This patch fixes the bpf helper by checking skb_transport_header_was_set(). The check is done just before skb->transport_header is used, to avoid breaking the existing bpf prog. The WARN_ON_ONCE is limited to bpf_prog_test_run, so targeting bpf-next.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix racy bitfield write in btrfs_clear_space_info_full() From the memory-barriers.txt document regarding memory barrier ordering guarantees: (*) These guarantees do not apply to bitfields, because compilers often generate code to modify these using non-atomic read-modify-write sequences. Do not attempt to use bitfields to synchronize parallel algorithms. (*) Even in cases where bitfields are protected by locks, all fields in a given bitfield must be protected by one lock. If two fields in a given bitfield are protected by different locks, the compiler's non-atomic read-modify-write sequences can cause an update to one field to corrupt the value of an adjacent field. btrfs_space_info has a bitfield sharing an underlying word consisting of the fields full, chunk_alloc, and flush: struct btrfs_space_info { struct btrfs_fs_info * fs_info; /* 0 8 */ struct btrfs_space_info * parent; /* 8 8 */ ... int clamp; /* 172 4 */ unsigned int full:1; /* 176: 0 4 */ unsigned int chunk_alloc:1; /* 176: 1 4 */ unsigned int flush:1; /* 176: 2 4 */ ... Therefore, to be safe from parallel read-modify-writes losing a write to one of the bitfield members protected by a lock, all writes to all the bitfields must use the lock. They almost universally do, except for btrfs_clear_space_info_full() which iterates over the space_infos and writes out found->full = 0 without a lock. Imagine that we have one thread completing a transaction in which we finished deleting a block_group and are thus calling btrfs_clear_space_info_full() while simultaneously the data reclaim ticket infrastructure is running do_async_reclaim_data_space(): T1 T2 btrfs_commit_transaction btrfs_clear_space_info_full data_sinfo->full = 0 READ: full:0, chunk_alloc:0, flush:1 do_async_reclaim_data_space(data_sinfo) spin_lock(&space_info->lock); if(list_empty(tickets)) space_info->flush = 0; READ: full: 0, chunk_alloc:0, flush:1 MOD/WRITE: full: 0, chunk_alloc:0, flush:0 spin_unlock(&space_info->lock); return; MOD/WRITE: full:0, chunk_alloc:0, flush:1 and now data_sinfo->flush is 1 but the reclaim worker has exited. This breaks the invariant that flush is 0 iff there is no work queued or running. Once this invariant is violated, future allocations that go into __reserve_bytes() will add tickets to space_info->tickets but will see space_info->flush is set to 1 and not queue the work. After this, they will block forever on the resulting ticket, as it is now impossible to kick the worker again. I also confirmed by looking at the assembly of the affected kernel that it is doing RMW operations. For example, to set the flush (3rd) bit to 0, the assembly is: andb $0xfb,0x60(%rbx) and similarly for setting the full (1st) bit to 0: andb $0xfe,-0x20(%rax) So I think this is really a bug on practical systems. I have observed a number of systems in this exact state, but am currently unable to reproduce it. Rather than leaving this footgun lying around for the future, take advantage of the fact that there is room in the struct anyway, and that it is already quite large and simply change the three bitfield members to bools. This avoids writes to space_info->full having any effect on ---truncated---

In the Linux kernel, the following vulnerability has been resolved: iomap: allocate s_dio_done_wq for async reads as well Since commit 222f2c7c6d14 ("iomap: always run error completions in user context"), read error completions are deferred to s_dio_done_wq. This means the workqueue also needs to be allocated for async reads.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Prevent recursive memory reclaim Function new_inode() returns a new inode with inode->i_mapping->gfp_mask set to GFP_HIGHUSER_MOVABLE. This value includes the __GFP_FS flag, so allocations in that address space can recurse into filesystem memory reclaim. We don't want that to happen because it can consume a significant amount of stack memory. Worse than that is that it can also deadlock: for example, in several places, gfs2_unstuff_dinode() is called inside filesystem transactions. This calls filemap_grab_folio(), which can allocate a new folio, which can trigger memory reclaim. If memory reclaim recurses into the filesystem and starts another transaction, a deadlock will ensue. To fix these kinds of problems, prevent memory reclaim from recursing into filesystem code by making sure that the gfp_mask of inode address spaces doesn't include __GFP_FS. The "meta" and resource group address spaces were already using GFP_NOFS as their gfp_mask (which doesn't include __GFP_FS). The default value of GFP_HIGHUSER_MOVABLE is less restrictive than GFP_NOFS, though. To avoid being overly limiting, use the default value and only knock off the __GFP_FS flag. I'm not sure if this will actually make a difference, but it also shouldn't hurt. This patch is loosely based on commit ad22c7a043c2 ("xfs: prevent stack overflows from page cache allocation"). Fixes xfstest generic/273.

In the Linux kernel, the following vulnerability has been resolved: ALSA: dice: fix buffer overflow in detect_stream_formats() The function detect_stream_formats() reads the stream_count value directly from a FireWire device without validating it. This can lead to out-of-bounds writes when a malicious device provides a stream_count value greater than MAX_STREAMS. Fix by applying the same validation to both TX and RX stream counts in detect_stream_formats().

In the Linux kernel, the following vulnerability has been resolved: macintosh/mac_hid: fix race condition in mac_hid_toggle_emumouse The following warning appears when running syzkaller, and this issue also exists in the mainline code. ------------[ cut here ]------------ list_add double add: new=ffffffffa57eee28, prev=ffffffffa57eee28, next=ffffffffa5e63100. WARNING: CPU: 0 PID: 1491 at lib/list_debug.c:35 __list_add_valid_or_report+0xf7/0x130 Modules linked in: CPU: 0 PID: 1491 Comm: syz.1.28 Not tainted 6.6.0+ #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:__list_add_valid_or_report+0xf7/0x130 RSP: 0018:ff1100010dfb7b78 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffffffa57eee18 RCX: ffffffff97fc9817 RDX: 0000000000040000 RSI: ffa0000002383000 RDI: 0000000000000001 RBP: ffffffffa57eee28 R08: 0000000000000001 R09: ffe21c0021bf6f2c R10: 0000000000000001 R11: 6464615f7473696c R12: ffffffffa5e63100 R13: ffffffffa57eee28 R14: ffffffffa57eee28 R15: ff1100010dfb7d48 FS: 00007fb14398b640(0000) GS:ff11000119600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000010d096005 CR4: 0000000000773ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 80000000 Call Trace: <TASK> input_register_handler+0xb3/0x210 mac_hid_start_emulation+0x1c5/0x290 mac_hid_toggle_emumouse+0x20a/0x240 proc_sys_call_handler+0x4c2/0x6e0 new_sync_write+0x1b1/0x2d0 vfs_write+0x709/0x950 ksys_write+0x12a/0x250 do_syscall_64+0x5a/0x110 entry_SYSCALL_64_after_hwframe+0x78/0xe2 The WARNING occurs when two processes concurrently write to the mac-hid emulation sysctl, causing a race condition in mac_hid_toggle_emumouse(). Both processes read old_val=0, then both try to register the input handler, leading to a double list_add of the same handler. CPU0 CPU1 ------------------------- ------------------------- vfs_write() //write 1 vfs_write() //write 1 proc_sys_write() proc_sys_write() mac_hid_toggle_emumouse() mac_hid_toggle_emumouse() old_val = *valp // old_val=0 old_val = *valp // old_val=0 mutex_lock_killable() proc_dointvec() // *valp=1 mac_hid_start_emulation() input_register_handler() mutex_unlock() mutex_lock_killable() proc_dointvec() mac_hid_start_emulation() input_register_handler() //Trigger Warning mutex_unlock() Fix this by moving the old_val read inside the mutex lock region.

In the Linux kernel, the following vulnerability has been resolved: md: init bioset in mddev_init IO operations may be needed before md_run(), such as updating metadata after writing sysfs. Without bioset, this triggers a NULL pointer dereference as below: BUG: kernel NULL pointer dereference, address: 0000000000000020 Call Trace: md_update_sb+0x658/0xe00 new_level_store+0xc5/0x120 md_attr_store+0xc9/0x1e0 sysfs_kf_write+0x6f/0xa0 kernfs_fop_write_iter+0x141/0x2a0 vfs_write+0x1fc/0x5a0 ksys_write+0x79/0x180 __x64_sys_write+0x1d/0x30 x64_sys_call+0x2818/0x2880 do_syscall_64+0xa9/0x580 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Reproducer ``` mdadm -CR /dev/md0 -l1 -n2 /dev/sd[cd] echo inactive > /sys/block/md0/md/array_state echo 10 > /sys/block/md0/md/new_level ``` mddev_init() can only be called once per mddev, no need to test if bioset has been initialized anymore.

In the Linux kernel, the following vulnerability has been resolved: scsi: smartpqi: Fix device resources accessed after device removal Correct possible race conditions during device removal. Previously, a scheduled work item to reset a LUN could still execute after the device was removed, leading to use-after-free and other resource access issues. This race condition occurs because the abort handler may schedule a LUN reset concurrently with device removal via sdev_destroy(), leading to use-after-free and improper access to freed resources. - Check in the device reset handler if the device is still present in the controller's SCSI device list before running; if not, the reset is skipped. - Cancel any pending TMF work that has not started in sdev_destroy(). - Ensure device freeing in sdev_destroy() is done while holding the LUN reset mutex to avoid races with ongoing resets.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix peer HE MCS assignment In ath11k_wmi_send_peer_assoc_cmd(), peer's transmit MCS is sent to firmware as receive MCS while peer's receive MCS sent as transmit MCS, which goes against firmwire's definition. While connecting to a misbehaved AP that advertises 0xffff (meaning not supported) for 160 MHz transmit MCS map, firmware crashes due to 0xffff is assigned to he_mcs->rx_mcs_set field. Ext Tag: HE Capabilities [...] Supported HE-MCS and NSS Set [...] Rx and Tx MCS Maps 160 MHz [...] Tx HE-MCS Map 160 MHz: 0xffff Swap the assignment to fix this issue. As the HE rate control mask is meant to limit our own transmit MCS, it needs to go via he_mcs->rx_mcs_set field. With the aforementioned swapping done, change is needed as well to apply it to the peer's receive MCS. Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: isdn: mISDN: hfcsusb: fix memory leak in hfcsusb_probe() In hfcsusb_probe(), the memory allocated for ctrl_urb gets leaked when setup_instance() fails with an error code. Fix that by freeing the urb before freeing the hw structure. Also change the error paths to use the goto ladder style. Compile tested only. Issue found using a prototype static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix invalid prog->stats access when update_effective_progs fails Syzkaller triggers an invalid memory access issue following fault injection in update_effective_progs. The issue can be described as follows: __cgroup_bpf_detach update_effective_progs compute_effective_progs bpf_prog_array_alloc <-- fault inject purge_effective_progs /* change to dummy_bpf_prog */ array->items[index] = &dummy_bpf_prog.prog ---softirq start--- __do_softirq ... __cgroup_bpf_run_filter_skb __bpf_prog_run_save_cb bpf_prog_run stats = this_cpu_ptr(prog->stats) /* invalid memory access */ flags = u64_stats_update_begin_irqsave(&stats->syncp) ---softirq end--- static_branch_dec(&cgroup_bpf_enabled_key[atype]) The reason is that fault injection caused update_effective_progs to fail and then changed the original prog into dummy_bpf_prog.prog in purge_effective_progs. Then a softirq came, and accessing the members of dummy_bpf_prog.prog in the softirq triggers invalid mem access. To fix it, skip updating stats when stats is NULL.

In the Linux kernel, the following vulnerability has been resolved: bpf: Free special fields when update [lru_,]percpu_hash maps As [lru_,]percpu_hash maps support BPF_KPTR_{REF,PERCPU}, missing calls to 'bpf_obj_free_fields()' in 'pcpu_copy_value()' could cause the memory referenced by BPF_KPTR_{REF,PERCPU} fields to be held until the map gets freed. Fix this by calling 'bpf_obj_free_fields()' after 'copy_map_value[,_long]()' in 'pcpu_copy_value()'.

In the Linux kernel, the following vulnerability has been resolved: usb: potential integer overflow in usbg_make_tpg() The variable tpgt in usbg_make_tpg() is defined as unsigned long and is assigned to tpgt->tport_tpgt, which is defined as u16. This may cause an integer overflow when tpgt is greater than USHRT_MAX (65535). I haven't tried to trigger it myself, but it is possible to trigger it by calling usbg_make_tpg() with a large value for tpgt. I modified the type of tpgt to match tpgt->tport_tpgt and adjusted the relevant code accordingly. This patch is similar to commit 59c816c1f24d ("vhost/scsi: potential memory corruption").

In the Linux kernel, the following vulnerability has been resolved: ping: Fix potentail NULL deref for /proc/net/icmp. After commit dbca1596bbb0 ("ping: convert to RCU lookups, get rid of rwlock"), we use RCU for ping sockets, but we should use spinlock for /proc/net/icmp to avoid a potential NULL deref mentioned in the previous patch. Let's go back to using spinlock there. Note we can convert ping sockets to use hlist instead of hlist_nulls because we do not use SLAB_TYPESAFE_BY_RCU for ping sockets.