CVE Feed

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: drop oversized fragments to avoid extra_len overflow In ieee80211_rx_h_defragment(), fragment payloads are accumulated into entry->extra_len as subsequent fragments arrive: entry->extra_len += rx->skb->len; When the final fragment arrives, the head fragment is dequeued, and pskb_expand_head() is called with entry->extra_len to ensure sufficient tailroom for all queued fragments before copying: if (skb_tailroom(rx->skb) < entry->extra_len) { if (unlikely(pskb_expand_head(rx->skb, 0, entry->extra_len, GFP_ATOMIC))) { ... } } while ((skb = __skb_dequeue(&entry->skb_list))) { skb_put_data(rx->skb, skb->data, skb->len); dev_kfree_skb(skb); } In commit 69f132236827 ("mac80211: shrink struct ieee80211_fragment_entry"), entry->extra_len was narrowed from unsigned int to u16 in order to reduce structure memory footprint. However, an IEEE 802.11 frame sequence can contain up to 16 fragments (frag numbers 0..15). If a sequence of large fragments arrives (e.g. from a malicious peer or rogue AP), the sum of fragment lengths can exceed 65535 bytes (for example, 15 fragments of 4400 bytes total 66000 bytes). Because extra_len is a u16, this addition overflows and wraps around modulo 65536 (e.g. 66000 wraps to 464). Consequently, pskb_expand_head() allocates only the truncated amount of tailroom (or is skipped entirely if the head fragment already has >= 464 bytes of tailroom). When skb_put_data() subsequently iterates through the queued skb list, it appends the full payload into the undersized buffer, causing skb_put() to trigger skb_over_panic() and crash the kernel in softirq context. A legitimate MSDU in IEEE 802.11 is at most 2304 bytes (or up to 7935/11454 bytes for A-MSDU, which is not fragmented), well below U16_MAX. Fix this without increasing the size of struct ieee80211_fragment_entry by checking whether adding the incoming fragment length would exceed U16_MAX. If so, purge the queued fragments and drop the frame. [assign a separate drop reason]

In the Linux kernel, the following vulnerability has been resolved: blk-cgroup: save IRQ state in blkg_tryget_closest() bio_set_dev() associates the bio with a blkg through bio_associate_blkg(). If the blkg lookup misses, blkg_tryget_closest() takes q->queue_lock with spin_lock_irq() and releases it with spin_unlock_irq(), which unconditionally enables local interrupts. Callers may call bio_set_dev() with interrupts already disabled, e.g. dm-thin's pool_map() does so while holding pool->lock taken with spin_lock_irq(). The nested spin_unlock_irq() then enables interrupts while pool->lock is still held, so an I/O completion softirq can run on the same CPU, re-acquire pool->lock (thin_endio(), or overwrite_endio() -> complete_mapping_preparation()) and deadlock. lockdep reports this as inconsistent SOFTIRQ-ON-W to IN-SOFTIRQ-W usage. Commit 3a762de55b4e ("block: save irq state in blkg_lookup_create()") fixed the same problem while the lock lived in blkg_lookup_create(), but commit 9327a865e395 ("blk-cgroup: don't nest queue_lock under rcu in blkg_lookup_create()") moved the locking into blkg_tryget_closest() and reverted it to spin_lock_irq(). Save and restore the caller's IRQ state instead.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k_htc: bound TX aggregation to MAX_TX_BUF_SIZE __hif_usb_tx() dequeues up to MAX_TX_AGGR_NUM (20) frames into a single tx_buf of MAX_TX_BUF_SIZE (32768) bytes, limiting the batch by record count but never by cumulative byte length. With large frames (MTU 2304), 20 aggregated frames of 2292 bytes each exceed the allocation (20 * 2296 = 45920 bytes), so the memcpy() in the loop writes up to 13152 bytes past tx_buf->buf before usb_submit_urb(). Peek the queue head and stop before copying any record that would cross MAX_TX_BUF_SIZE, then dispatch the current batch. Leftover skbs remain queued and are drained on the next URB completion. The byte bound changes the loop's exit semantics: it can now exit before i == tx_skb_cnt - 1. Stock only finalized tx_buf->len on that last index (len += offset), so an early break would submit a URB holding only the last record's length while every dequeued skb is freed on completion, silently dropping frames. Make tx_buf->len a running total and advance tx_buf->offset per record instead; the stride round_up(nskb->len + 4, 4) is identical to the stock stride when the loop runs to completion. Tested on hardware with an MTU 2304 flood: the loop stops at record 15 (len = 32144, offset = 32144, within 32768), no oversized URB is submitted, and MTU 1500 pings pass 20/20.

In the Linux kernel, the following vulnerability has been resolved: iio: accel: kionix-kx022a: Fix array boundary check The driver performs a sanity check for an array size, when converting a register value to an array index. The check incorrectly accepts the sizeof(array) as a last index, when last valid index should be sizeof(array) - 1. Fix the check by bailing out when index >= sizeof(array).

In the Linux kernel, the following vulnerability has been resolved: netfs: zero gaps in read-gaps folio to avoid writing back stale data netfs_read_gaps() leaves gaps around a streaming write's dirty region unread on the server side, so a short/EOF response there left stale folio content that later got written back. Zero it after the read completes, not before: netfs_wait_for_read() returns rreq->transferred once ret >= 0, so build an iterator over the same bvec array the read used, advance past ret, and zero the rest. The dirty region already maps to sink pages in that array rather than the real folio, so this can't touch it, and only the actual shortfall gets zeroed instead of the whole gap upfront.

In the Linux kernel, the following vulnerability has been resolved: mtd: core: avoid double-free of OTP NVMEM device If factory OTP setup fails after the user OTP NVMEM device has been registered, mtd_otp_nvmem_add() unregisters the user device but leaves mtd->otp_user_nvmem set. On an error, the caller unregisters it again. For -EOPNOTSUPP, registration continues and normal teardown unregisters it again. Clear mtd->otp_user_nvmem after unregistering it.

In the Linux kernel, the following vulnerability has been resolved: ALSA: line6: reject oversized playback packets Each playback URB is handed a slice of out.buffer that is exactly LINE6_ISO_PACKETS * max_packet_size_out bytes, sized from the OUT endpoint, but the number of bytes written into that slice is never compared against it. submit_audio_out_urb() takes the frame count from prev_fsize, which audio_in_callback() derived from the *IN* endpoint's received packet length, and rescales it with the playback frame size; when prev_fsize is still zero it synthesizes a length from the sample rate instead. On a device declaring a large IN wMaxPacketSize and a small OUT wMaxPacketSize, the resulting memcpy(), or the memset() when the playback stream is idle, runs past its slice and, as the reproducer below shows, beyond the allocation. usb_submit_urb() is not a backstop. max_packet_size_out comes from usb_maxpacket(), which returns only the low 11 bits of wMaxPacketSize, while USB core validates a high-speed isochronous length against that base scaled by usb_endpoint_maxp_mult(). A length of up to three times the allocated slice is therefore accepted, and even a rejected URB is only rejected after the write. Reject a packet that does not fit the slice the driver allocated for it. Clamping it instead would silently shorten the capture-derived rate feedback and desynchronize the two streams. BUG: KASAN: slab-out-of-bounds in submit_audio_out_urb (sound/usb/line6/playback.c:229) Write of size 1024 at addr ffff888100bbd400 by task kworker/1:2/5002 Workqueue: events line6_startup_work Call Trace: __asan_memcpy (mm/kasan/shadow.c:106) submit_audio_out_urb (sound/usb/line6/playback.c:229) line6_submit_audio_out_all_urbs (sound/usb/line6/playback.c:291) line6_stream_start (sound/usb/line6/pcm.c:194) line6_pcm_acquire (sound/usb/line6/pcm.c:337) line6_startup_work (sound/usb/line6/driver.c:728) process_one_work (kernel/workqueue.c:3396) worker_thread (kernel/workqueue.c:3479 kernel/workqueue.c:3560) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) The buggy address belongs to the object at ffff888100bbd400 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 0 bytes inside of allocated 256-byte region [ffff888100bbd400, ffff888100bbd500)

In the Linux kernel, the following vulnerability has been resolved: netfs: clear post-EOF pagecache when extending a file via write Fix netfs to erase the contents of a hole created after the EOF by an ordinary write if dirty data has been previously left there by writes through an mmapped region. Neither the buffered nor the unbuffered/DIO write path clears that stale pagecache. Zero the tail of the folio straddling the EOF before an extending write. That is the only folio that can hold data written past the EOF through an mmap, as pages wholly beyond the EOF can't be faulted in. The folio is zeroed rather than dropped so a concurrent extending write can't lose data. Both write paths downgrade the i_rwsem to shared, so extending writes can run concurrently and the i_size read by the caller may be stale by the time the folio is locked. Re-read i_size under the folio lock and clamp the zeroed range up to it, so a racing write that already put data into the folio isn't clobbered. Wait for any writeback on the folio to finish before zeroing it so that the pagecache isn't modified while it may still be read by the transport during transmission. Honour IOCB_NOWAIT by returning -EAGAIN rather than blocking on the folio lock, on writeback, or in folio_mkclean()'s rmap walk when the folio is mapped. truncate_pagecache() can't be used here: it must be called with the i_rwsem held exclusively, but these write paths only hold it shared, and it would block unconditionally, breaking IOCB_NOWAIT. Callers that hold i_rwsem exclusively for the whole resize (truncate, setattr, fallocate, clone) exclude any genuine concurrent buffered writer, so staleness can instead be decided from the folio's dirty state, as pagecache_isize_extended() already does for filesystems that serialise writes against truncate/setattr via a single i_rwsem. Export netfs_clear_stale_post_isize() helper to handle such case. The helper is required by the CIFS client to fix generic/363.

In the Linux kernel, the following vulnerability has been resolved: net: extend IPv6 exthdr detection of tunneled packets Commit c4336a07eb6b ("net: correctly handle tunneled traffic on IPV6_CSUM GSO fallback") split skb_gso_has_extension_hdr() into mutually exclusive branches on skb->encapsulation. This did not yet address all paths: 1. With skb->encapsulation set, the outer header is not checked. IPv6 tunnels such as ip6_gre and ip6_tunnel add an outer Destination Options header by default (encap_limit). Their GSO packets skip software GSO, then skb_csum_hwoffload_help() sees the outer extension header and calls skb_checksum_help() on the GSO skb, which warns and drops it. 2. Tunnels over IPv6 without an outer transport header, such as ip6_tunnel, leave skb->transport_header at the inner transport header. skb_network_header_len() then spans the outer IPv6, tunnel and inner IP headers, a false positive. 3. UDP tunnels without an inner network header, such as SCTP-in-UDP or PSP, have no inner IPv6 header to check. Decide on the outer header alone. 4. Directly dereferencing inner_ip_hdr(skb)->version without skb_header_pointer() is unsafe. Instead, check ipv6_ext_hdr(nexthdr) on the outer IPv6 header and, if set, on the inner IPv6 header. Read the headers with skb_header_pointer(). Keep the skb_network_header_len() check when !skb->encapsulation to also catch encapsulated packets without skb->encapsulation (e.g., virtio). Use the same helper in skb_csum_hwoffload_help(). Its open coded test has the false positive of (2) and ignores the inner header. Background: checksum offload of tunneled packets invariants: Non-GSO skb: - If the inner packet is CHECKSUM_PARTIAL, Local Checksum Offload computes the outer checksum in software and the device offloads only the inner L4 checksum. - If the inner packet is CHECKSUM_NONE (e.g., SCTP-in-UDP, ESP-in-UDP, Remote Checksum Offload), the device offloads the outer UDP or GRE checksum instead. GSO skb: - A device with NETIF_F_GSO_UDP_TUNNEL_CSUM or NETIF_F_GSO_GRE_CSUM computes both inner and outer checksums per segment. The outer checksum is seeded with only the pseudo-header checksum. A NETIF_F_IPV6_CSUM device must parse through the outer headers to reach the inner ones.

In the Linux kernel, the following vulnerability has been resolved: drm/client: fix restore of partially initialized client I got a null-ptr-deref report when closing a DRM file descriptor: WARNING: drivers/gpu/drm/drm_atomic.c:2031 at __drm_atomic_helper_set_config+0x18e/0x1b0 [drm] Call Trace: drm_client_modeset_commit_atomic+0x16b/0x220 [drm] drm_client_modeset_commit_locked+0x56/0x160 [drm] drm_client_modeset_commit+0x21/0x40 [drm] __drm_fb_helper_restore_fbdev_mode_unlocked.part.0+0x7b/0x80 drm_fbdev_client_restore+0xe/0x20 [drm_client_lib] drm_client_dev_restore+0x9f/0xc0 [drm] drm_release+0xc5/0xe0 [drm] The warning is followed by a NULL pointer dereference: BUG: kernel NULL pointer dereference, address: 0000000000000008 RIP: __drm_fb_helper_restore_fbdev_mode_unlocked.part.0+0x41/0x80 [drm_kms_helper] Call Trace: drm_fbdev_client_restore+0xe/0x20 [drm_client_lib] drm_client_dev_restore+0x9f/0xc0 [drm] drm_release+0xc5/0xe0 [drm] __fput+0xdc/0x2b0 __x64_sys_close+0x39/0x80 do_syscall_64+0x8d/0x460 entry_SYSCALL_64_after_hwframe+0x76/0x7e drm_client_register() adds the DRM client to the device client list before invoking the initial hotplug callback. If the hotplug callback fails, the client remains registered. For the fbdev client, a failure during drm_fb_helper_initial_config() causes the partially initialized fbdev helper to be cleaned up. drm_fb_helper_fini() releases fb_helper->info and leaves it NULL. The fbdev client therefore remains registered even though there is no fully initialized framebuffer device. Later, when userspace closes the DRM file descriptor, drm_release() can invoke the restore callbacks of registered DRM clients: drm_release() drm_client_dev_restore() drm_fbdev_client_restore() drm_fb_helper_restore_fbdev_mode_unlocked() drm_fbdev_client_restore() currently restores the fbdev state unconditionally. For a partially initialized fbdev client this can submit an incomplete modeset state and subsequently access fbdev state which has not been initialized, resulting in the warning and NULL pointer dereference above. drm_fbdev_client_unregister() already uses fb_helper->info to distinguish a fully probed framebuffer device from a partially initialized client. Use the same condition in drm_fbdev_client_restore() and skip restore if no framebuffer device has been successfully initialized.

In the Linux kernel, the following vulnerability has been resolved: arm64/boot: Disable trapping of PMZR_EL0 writes to EL2 __init_el2_fgt2() writes one mask to both HDFGRTR2_EL2 and HDFGWTR2_EL2. PMZR_EL0 is write-only, so its trap bit, nPMZR_EL0, exists only in HDFGWTR2_EL2 and is therefore never set: a PMZR_EL0 write from the host traps to EL2, where the nVHE hypervisor has no handler and BUG()s. The kernel never writes PMZR_EL0, but kernel.perf_user_access=1 has the PMU driver set PMUSERENR_EL0.UEN for a task with a user-read event, so a write from EL0 reaches the trap and takes the host down without a panic message. Accumulate the HDFGWTR2_EL2 bits separately, as __init_el2_fgt() already does for HDFGWTR_EL2, and set nPMZR_EL0 with the other FEAT_PMUv3p9 bits.

In the Linux kernel, the following vulnerability has been resolved: tipc: reject invalid and unexpected GRP_ACK_MSG to prevent bc_ackers underflow Commit 48a5fe38772b ("tipc: fix bc_ackers underflow on duplicate GRP_ACK_MSG") rejected duplicate/stale ACKs in tipc_group_proto_rcv() by returning early when less_eq(acked, m->bc_acked). However, that check remains incomplete in two ways: 1. When grp->bc_ackers is zero (e.g. on a quiet group, when replicast ACKs were not requested, or after all expected members have already acknowledged), an unexpected GRP_ACK_MSG with acked > m->bc_acked passes less_eq() and unconditionally decrements grp->bc_ackers. Because bc_ackers is a u16, this wraps to 65535, causing tipc_group_bc_cong() to permanently report congestion and blocking all future group broadcasts on the socket. 2. During an active broadcast round (grp->bc_ackers > 0), the sender transmits packet S and advances grp->bc_snd_nxt to S + 1. Receivers increment their expected counter to S + 1 upon consuming packet S, so the only valid ACK value for the current round is strictly acked == grp->bc_snd_nxt. However, tipc_group_update_bc_members() initializes each member's m->bc_acked to prev = grp->bc_snd_nxt - 1 (S - 1 before increment). This leaves a 2-sequence gap (S - 1 to S + 1) in sequence space. An incoming ACK is therefore neither rejected as duplicate nor prevented from decrementing grp->bc_ackers if an unexpected or stale value (such as S) is received. A member sending acked = S followed by acked = S + 1 could decrement grp->bc_ackers twice in the same round, prematurely clearing bc_ackers or underflowing it. Fix this by: - Dropping GRP_ACK_MSG immediately if grp->bc_ackers is zero. - Requiring acked == grp->bc_snd_nxt and rejecting duplicates where m->bc_acked == acked. Because replicast broadcast rounds are strictly sequential, only grp->bc_snd_nxt can be acknowledged, and each member can acknowledge at most once per round. Note that a related pre-existing issue in tipc_group_delete_member() (where grp->bc_ackers decrementing to zero upon member departure does not restore *grp->open or trigger a socket wakeup) will be addressed in a separate patch.

In the Linux kernel, the following vulnerability has been resolved: tcp: prevent collapsing skbs across boundary in rtx queue tcp_write_collapse_fence() sets TCP_SKB_CB(skb)->eor = 1 on tcp_write_queue_tail(sk) to prevent skbs queued after a switch to device encryption from being collapsed into earlier skbs. The fence is a no-op if all earlier data has already been transmitted when the switch happens: sk->sk_write_queue is empty. The not yet acknowledged earlier skbs wait in sk->tcp_rtx_queue with eor 0. On a subsequent retransmit or SACK shift, tcp_retrans_try_collapse() or tcp_shift_skb_data() can then merge an skb queued after the switch into one queued before it. Both users of the fence are affected: - psp: devices only encrypt skbs with skb->decrypted set. The merged skb keeps decrypted = 0 from the earlier skb, so merged data sent after psp_sock_assoc_set_tx() is retransmitted in cleartext. - tls device offload: the merged skb straddles the start marker set in tls_set_device_offload(). The software fallback (fill_sg_in() returns -EINVAL) and the mlx5, nfp and funeth drivers cannot handle such an skb and drop it. Every retransmit rebuilds the same skb, so the connection stalls. Fix this in two places, for defense in depth: 1. Fall back to tcp_rtx_queue_tail(sk) in tcp_write_collapse_fence() when tcp_write_queue_tail(sk) is NULL. 2. Check !skb_cmp_decrypted(to, from) in tcp_skb_can_collapse(), as tcp_skb_can_collapse_rx() does on receive. skb_shift(), which both collapse paths call, already has a DEBUG_NET_WARN_ON_ONCE() for this condition.

In the Linux kernel, the following vulnerability has been resolved: net/sched: fix potential stack infoleak in em_text_dump() em_text_dump() allocates struct tcf_em_text on the stack without zeroing it. strscpy() writes the algorithm name and a NUL terminator into conf.algo[], leaving the remaining bytes uninitialised. nla_put_nohdr() then copies the full struct to the netlink response. KMSAN on Linux 7.2-rc6 reports two kernel-infoleak splats from this path, one triggered via "tc filter show" and one via a raw RTM_GETTFILTER dump: BUG: KMSAN: kernel-infoleak in _copy_to_iter+0x1c9/0x2620 nla_put_nohdr+0x83/0x130 em_text_dump+0x291/0x550 Local variable conf created at: em_text_dump+0x5d/0x550 Bytes 168-179 of 199 are uninitialized I am not certain whether this constitutes a real security problem in practice: the test was conducted in a controlled KMSAN environment and the leaked stack bytes may or may not carry sensitive data on actual production kernels. I am reporting it because KMSAN flagged it as a kernel-infoleak and the fix is straightforward. I can provide a userspace reproducer on request. The original code used strncpy() which zero-pads to the destination size. Commit b04202d6065c ("net/sched: replace strncpy with strscpy") replaced it with strscpy(), which does not pad, creating this condition. Zero-initialising the struct closes it.

In the Linux kernel, the following vulnerability has been resolved: sctp: hold asoc or transport before mod_timer() in timer handlers Take the association or transport reference before rearming a timer in the timer handlers. The existing code calls mod_timer() before taking the reference needed by the rearmed timer without holding the sock lock. This creates a race with timer cleanup: if the timer is deleted after mod_timer() returns but before the reference is taken, the cleanup path can drop the timer's reference and destroy the transport or association. The timer handler then takes a reference on the already freed object and eventually drops it, causing a refcount underflow. Hold the object before mod_timer() and drop the reference if mod_timer() reports that the timer was already pending in timer handlers. Apply the same ordering to the proto-unreachable path, which can rearm a transport timer outside the timer handlers without holding the sock lock.

In the Linux kernel, the following vulnerability has been resolved: net: spacemit: clear TX descriptor on fragment mapping failure emac_tx_mem_map() writes TX_DESC_0_OWN into the ring descriptor for every slot beyond old_head as soon as that slot's memset()'d local copy is committed with "*tx_desc_addr = tx_desc", i.e. before the buffers for that slot have necessarily all been mapped successfully. If emac_tx_map_frag() then fails on a later fragment, the err_free_skb path calls emac_free_tx_buf() to unmap and drop the skb, but leaves the already-written descriptor memory untouched, and tx_ring->head is never advanced past old_head (the "tx_ring->head = head" store is skipped by the goto). So a slot between old_head and the rolled-back head can be left with TX_DESC_0_OWN set and buffer_addr_{1,2} pointing at DMA mappings that emac_free_tx_buf() just tore down, while software considers that slot free again. The next successful emac_tx_mem_map() call only rebuilds old_head itself; if the DMA engine auto-advances into the following descriptor once it finishes old_head's packet, it will fetch that stale, already-unmapped address. emac_tx_clean_desc() already treats emac_free_tx_buf() and clearing the descriptor as a pair when reclaiming completed descriptors; do the same in the mapping failure path.

In the Linux kernel, the following vulnerability has been resolved: scsi: block: Fix zones_cond out-of-bounds write on zone report blk_revalidate_disk_zones() sizes the zones_cond array from the disk capacity and zone size, but the index used by blk_revalidate_zone_cond() comes from the device-driven report_zones() walk and is never checked against the array size. A device reporting more zones than fit the array makes blk_zone_set_cond() write out of bounds. One way to reach this is a zone count exceeding 32 bits: both blk_revalidate_zone_args.nr_zones and struct zoned_disk_info.nr_zones are unsigned int, so a disk advertising more than UINT_MAX zones (e.g. 2^32 + 1024 zones of one 512-byte logical block) gets its zone count truncated to a small value, undersizing the array while the report walk keeps counting upward. Check the index against the array size before storing the zone condition, and refuse to revalidate when the zone count does not fit 32 bits.

In the Linux kernel, the following vulnerability has been resolved: squashfs: Add dictionary size range check to prevent shift-out-of-bounds When an abnormal SquashFS image (COMP_OPTS flag is 1 but dictionary size is 0) is mounted, and performs shift operations using dictionarysize, the shift exponent is -1, causing a shift-out-of-bounds. Detail as below: squashfs_comp_opts(msblk, buffer, length) squashfs_xz_comp_opts() if (comp_opts) n = ffs(opts->dict_size) - 1;<----opts->dict_size=0, n=-1 if (opts->dict_size != (1 << n) && opts->dict_size != (1 << n) + (1 << (n + 1))) <----shift-out-of-bounds Fix it by adding a dictionary size range check before the shift operation.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Validate the SVE vector length in pkvm_vcpu_init_sve() pkvm_vcpu_init_sve() clamps only the upper bound of the host-provided sve_max_vl, so an invalid vector length reaches sve_state_size_from_vl() and the WARN_ON() there, which is fatal at EL2. The existing !sve_state_size test rejects such a length, but only after the macro has run. Check sve_vl_valid() before deriving the state size. A valid length cannot yield a zero size, so the !sve_state_size test goes with it.

In the Linux kernel, the following vulnerability has been resolved: bpf, arm64: set up the frame pointer for the exception callback A program acting as exception boundary saves all callee-saved registers, so build_prologue() takes the exception_cb path and never calls push_callee_regs(). That is the only place find_used_callee_regs() runs, and with it the only place ctx->fp_used is set, so the callback prologue does not emit the mov x25, sp that points BPF_REG_FP at the frame the callback runs on. x25 keeps whatever it held when bpf_throw() was called. If the throw came from a subprogram that uses its own BPF stack, that is the subprogram's frame pointer, and since the subprogram never returns it never restores x25 either. Stack accesses through BPF_REG_FP are rewritten to be stack pointer relative, so those still land in the callback's own frame. Materializing the register does not: a callback that passes the address of a local variable to a helper hands over an address in the dead subprogram's frame. That address is below the callback's stack pointer by then, and the helper's own call chain covers it, so the helper can write over its own return address. 0x1234 below is the value the helper was asked to store: pc : 0x1234 lr : 0x1234 Call trace: 0x1234 (P) bpf_test_run+0x188/0x3e0 bpf_prog_test_run_skb+0x47c/0x998 __sys_bpf+0xbdc/0xdd8 Kernel panic - not syncing: Oops: Fatal exception in interrupt Set ctx->fp_used on the exception callback path so that the existing code further down sets x25 from the stack pointer. The epilogue restores it from the main program's save area along with the other callee-saved registers, as it already does. x86 sets the frame pointer for the callback from the argument it is passed, and powerpc computes it from the stack pointer.

In the Linux kernel, the following vulnerability has been resolved: HID: winwing: fix use-after-free in force feedback teardown winwing_init_ff() passes the driver's private data, allocated with devm_kzalloc() in winwing_probe(), as the effect context to input_ff_create_memless(). The memoryless force-feedback core takes ownership of that pointer and frees it with kfree() from input_ff_destroy() (ml_ff_destroy()) when the input device is destroyed. Freeing a devm-managed allocation with kfree() is an invalid free, and the same object is then released again by devres when the HID device is torn down, a double free. As the allocation also embeds the LED class devices, their timers and work item live on freed memory and the slab gets corrupted. This triggers on unbind, rmmod, hot-unplug and on system suspend, where the firmware cache walks the now-corrupt devres list. KASAN reports: BUG: KASAN: invalid-free in input_ff_destroy Allocated by task N: winwing_probe Pass NULL as the memless context instead and fetch the driver data from the input device in winwing_play_effect(): the HID core already stores the hid_device as the input device's drvdata. The force-feedback core then owns nothing that it must not free.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix out-of-bounds read of rtt_min in sock_ops A sockops prog reading skops->rtt_min never checks the sk type: on the tcp_conn_request() path sock_ops->sk is a request_sock (non-full), and the ctx rewrite casts it to a tcp_sock (full) and reads rtt_min past the end of the request_sock, returning dirty adjacent memory. SEC("sockops") int prog(struct bpf_sock_ops *skops) { switch (skops->op) { case BPF_SOCK_OPS_RWND_INIT: leak = skops->rtt_min; /* reads the request_sock OOB */ ... } } For instance one such read returned rtt_min=0xffff8881, the high half of a leaked kernel pointer. Guarding that cast is exactly what SOCK_OPS_GET_FIELD() does -- it checks is_locked_tcp_sock and returns 0 when sock_ops->sk is not a locked full socket. Every other tcp_sock field in sock_ops goes through it; rtt_min is the only one open-coded, so it skips the check. Read rtt_min through SOCK_OPS_GET_FIELD() too. rtt_min is a bit special: it is a struct minmax and we only want the current min, so pass rtt_min.s[0].v. That is equivalent to the old hand-computed offset offsetof(struct tcp_sock, rtt_min) + sizeof_field(struct minmax_sample, t) (s[0] sits at rtt_min + 0 and .v at + sizeof(.t), i.e. what minmax_get() returns), so the loaded field is unchanged and only the full-sock guard is added. The two BUILD_BUG_ON()s that protected the hand-computed offset are no longer needed. Before patch: 0: r1 = *(u64 *)(r1 +0) ; r1 = skops->sk 1: r1 = *(u32 *)(r1 +2324) ; ((tcp_sock *)sk)->rtt_min.s[0].v After patch: 0: *(u64 *)(r1 +56) = r9 1: r9 = *(u8 *)(r1 +50) ; is_locked_tcp_sock 2: if r9 == 0 goto pc+4 ; not a locked full sock -> 0 3: r9 = *(u64 *)(r1 +56) 4: r1 = *(u64 *)(r1 +0) ; r1 = skops->sk 5: r1 = *(u32 *)(r1 +2324) ; rtt_min.s[0].v 6: goto pc+2 7: r9 = *(u64 *)(r1 +56) 8: r1 = 0

In the Linux kernel, the following vulnerability has been resolved: KVM: s390: Fix race in _destroy_pages_crste() Use READ_ONCE() in _destroy_pages_crste() to read the crste, avoid dereferencing the pointer multiple times.

In the Linux kernel, the following vulnerability has been resolved: iio: pressure: rohm-bm1390: Return error when read fails The data reading function ignores the cached error value, and unconditionally returns 0. Return cached 'ret' -value after stopping the measurement so user knows if read failed and data is garbage.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: adi-axi-adc: Initialize state mutex The AXI ADC register access paths serialize transactions with st->lock, but probe does not initialize it. Initialize the mutex before registering the backend.

In the Linux kernel, the following vulnerability has been resolved: smb: client: drain and invalidate before server-side copy/clone cifs_file_copychunk_range() and the clone (FICLONE) path of cifs_remap_file_range() do not serialise the destination page cache against the server-side copy the way the other server-side range operations (smb3_zero_range(), smb3_punch_hole(), smb3_collapse_range() and smb3_insert_range()) do. cifs_file_copychunk_range() invalidates the destination range with filemap_invalidate_inode(), which takes and drops the mapping's invalidate_lock internally, so the lock is no longer held when the copychunk ioctl is issued. It also never drains in-flight netfs I/O on the target. The clone path never takes the invalidate_lock at all (only i_rwsem), uses a bare truncate_inode_pages_range() and likewise does not drain outstanding I/O. As a result an asynchronous destination writeback can complete after the server-side copy/clone has run and reinstate stale data over the region just written by the server, corrupting the file. This is the same class of corruption as commit d7d2adcd022b ("smb/client: flush dirty data before punching a hole") and has been seen randomly in generic/363 against Windows Server. Fix both paths to follow the established ordering: hold the target mapping's invalidate_lock across the flush and invalidation of the destination and the server ioctl, and call netfs_wait_for_outstanding_io() on the target to drain in-flight writes before the ioctl is issued. Only the target inode's invalidate_lock is required, as the source is merely flushed and not invalidated; i_rwsem (already held via lock_two_nondirectories()) is acquired before the invalidate_lock, matching the VFS lock ordering. Since filemap_invalidate_inode() takes that same lock internally, replace it with its own unmap/flush/invalidate steps instead of calling it, and return early on a zero-length copy to avoid a range underflow.

In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Fix domain reference leak when DPRX read is canceled tb_tunnel_one_dp() takes a domain reference which is only dropped once tb_dp_tunnel_active() has run on the work queue. If that work is cancelled that reference is leaked. Since commit f5cc545f5969 ("thunderbolt: Wait for tb_domain_release() to complete when driver is removed") instead of just leaking memory this now also blocks in the completion wait forever when unbinding the driver. This can be triggered whenever a DP tunnel is torn down before the DPRX read has completed, e.g. by unplugging within the timeout, and then unbinding the driver. That reference only exists to keep the domain around while the DPRX work is scheduled so let the work itself own it: take it in tb_dp_dprx_start() and drop it in both places that end the work. Get/put are then paired inside the same file and it doesn't matter anymore if the callback ever runs.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: Fix initial port reference race For RFCOMM_RELEASE_ONHUP devices, rfcomm_tty_install() and __rfcomm_release_dev() both use RFCOMM_TTY_OWNED to decide who drops the initial tty_port reference. The release path tests the bit separately from the install path setting it, so both can drop that reference. The synchronous hangup does not prevent this race: port->tty is not assigned until tty_port_open(), after installation. The following interleaving is possible: 1. Install and release each obtain a reference with rfcomm_dev_get(). 2. Release observes RFCOMM_TTY_OWNED clear. 3. Install sets RFCOMM_TTY_OWNED and drops the initial reference. 4. Release drops the same initial reference again. 5. TTY cleanup drops its reference and frees the device. 6. Release performs its final tty_port_put() on the freed port. KASAN reported: BUG: KASAN: slab-use-after-free in tty_port_put+0x22/0x190 Write of size 4 at addr ffff8881001d3d5c by task poc/92 Call Trace: tty_port_put+0x22/0x190 rfcomm_dev_ioctl+0x1d4/0x1930 sock_do_ioctl+0x110/0x260 sock_ioctl+0x380/0x590 __x64_sys_ioctl+0x134/0x1c0 Allocated by task 88: rfcomm_dev_ioctl+0x8f6/0x1930 sock_do_ioctl+0x110/0x260 sock_ioctl+0x380/0x590 __x64_sys_ioctl+0x134/0x1c0 Freed by task 65: kfree+0x131/0x3c0 rfcomm_dev_destruct+0x23b/0x2f0 release_one_tty+0xc1/0x370 process_one_work+0x661/0x1090 Use test_and_set_bit() in both paths so that only the caller that changes RFCOMM_TTY_OWNED from clear to set drops the initial reference. Each path keeps its own lookup reference until release or TTY cleanup, preserving the existing callback ordering and error handling.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix overflow of jump offset in constant blinding bpf_jit_blind_insn() rewrites 'if rX op imm goto off' into: AX = imm ^ rnd AX ^= rnd if rX op AX goto off and subtracts 2 from off when the jump is backward. off is s16, so -32767 and -32768 wrap and the jump goes 32767 insns forward, past the end of the prog. The jump is inside the patch, hence bpf_adj_branches() doesn't check it. The kernel crashes when such prog runs with bpf_jit_harden=2. Return -ERANGE in such case. bpf_jit_blind_constants() fails the same way when blinding of other insns moves a jump out of range.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: don't drain cmd_sync backlog on unregister hci_unregister_dev() disables cmd_work and cmd_timer, then calls hci_cmd_sync_clear(), whose cancel_work_sync() waits for hci_cmd_sync_work() to return. That worker dequeues and runs every entry on cmd_sync_work_list. With cmd_work disabled nothing reaches the controller, so each queued HCI command waits the full HCI_CMD_TIMEOUT (2s). The backlog has no bound. Userspace can keep queuing MGMT commands such as MGMT_OP_GET_CLOCK_INFO against a controller that doesn't answer. Closing /dev/vhci then blocks in vhci_release() for backlog * 2s: INFO: task syz-executor:5749 blocked for more than 143 seconds. cancel_work_sync hci_cmd_sync_clear hci_unregister_dev vhci_release In a local reproduction the backlog held more than 5000 entries, which comes to hours of hang. Stop the worker from taking new entries once HCI_UNREGISTER is set, and wake any request still waiting with -ENODEV before cancelling the work. The entries left over are destroyed with -ECANCELED by the existing sweep in hci_cmd_sync_clear(). They stay on the list until the work has stopped, so hci_cmd_sync_dequeue() and friends still see them. A callback already running may still issue another command, which delays unregister by at most one timeout per remaining command, not by the whole backlog.

In the Linux kernel, the following vulnerability has been resolved: net: phylink: record the PHY only once bringup cannot fail phylink_bringup_phy() stores the PHY in pl->phydev before its last fallible step: on a MAC whose phylink ops implement LPI, phy_eee_rx_clock_stop() can fail with a real MDIO error. The callers unwind with phy_detach(), which knows nothing about pl->phydev, so a pointer to a PHY that is no longer attached outlives the failed connect. What that costs depends on how the caller got here. phylink_connect_phy() goes through phylink_attach_phy(), which refuses to attach while pl->phydev is set, turning a transient MDIO error into a permanent -EBUSY. The SFP path is worse than that: sfp_sm_probe_phy() answers the failure with phy_device_remove() and phy_device_free(), and it assigns sfp->mod_phy only past that error return, so nothing clears pl->phydev and it is left pointing at a freed phy_device that phylink_resolve() and the ethtool helpers go on reading. phylink_fwnode_phy_connect() has no such check, so a later connect overwrites the stale pointer and hides the problem. A disconnect does not: phylink_disconnect_phy() hands that pointer to phy_disconnect(), and the second phy_detach() on the same PHY drops references the first one already released. Found while making a DSA port survive a PHY whose driver arrives after the switch probes: keeping the port across a failed connect and retrying is what makes this window reachable. Publish the pointer after the last call that can fail instead of unwinding it afterwards. Nothing between the two points reads pl->phydev, and the registration that follows cannot fail: phy_request_interrupt() falls back to polling on its own. The PHY-side state keeps the order it had, so no MDIO operation moves relative to another.

In the Linux kernel, the following vulnerability has been resolved: net: xps: reject an out of range traffic class Only the entries below dev->num_tc are valid in dev->tc_to_txq[], and dev->prio_tc_map[] may only name classes below it. netdev_set_num_tc() lowers dev->num_tc without touching either array. netdev_txq_to_tc() walks all TC_MAX_QUEUE slots and netdev_get_prio_tc_map() returns the entry as it stands, so a leftover entry is handed out as a traffic class >= dev->num_tc. Taking that class from netdev_txq_to_tc(), __netif_set_xps_queue() rejects only a negative one and indexes an XPS map sized for dev->num_tc classes: tci = j * num_tc + tc; RCU_INIT_POINTER(new_dev_maps->attr_map[tci], map); attr_map[] holds nr_ids * num_tc entries and j runs over the ids named in the mask, so a class that is not below num_tc pushes tci past the end of the map for the last ids and the store overruns it. Any caller that lowers num_tc leaves such entries behind, and mqprio_destroy() tears down with netdev_set_num_tc(dev, 0) rather than netdev_reset_tc(). After mqprio with 8 classes then 1, tc_to_txq[1..7] still describe txq 1..7. The splat is from an XPS write to txq 2 on a veth with 8 rx queues: attr_map[] has 8 * 1 entries, tci = j + 2, and j == 6 stores one past the end of the 88-byte map: BUG: KASAN: slab-out-of-bounds in __netif_set_xps_queue (net/core/dev.c:2954) Write of size 8 at addr ffff88813016bc58 by task xps_oob/634 __netif_set_xps_queue (net/core/dev.c:2954) xps_rxqs_store (net/core/net-sysfs.c:1880) netdev_queue_attr_store (net/core/net-sysfs.c:1390) Allocated by task 634: __kmalloc_noprof (mm/slub.c:5439) __netif_set_xps_queue (net/core/dev.c:2937) The buggy address is located 0 bytes to the right of allocated 88-byte region [ffff88813016bc00, ffff88813016bc58) Reject a class the map has no room for.

In the Linux kernel, the following vulnerability has been resolved: drm/imagination: clamp freelist reconstruction requests The firmware reconstruction count controls accesses to the request's fixed freelist ID array and the copy into the fixed response array. Neither access currently bounds the count to those protocol arrays. Clamp the count to the request capacity, which is shared by the response layout, and use that count consistently for reconstruction and response publication. Keep the firmware recovery exchange instead of dropping an oversized request without a response, as discussed with the firmware maintainer. The issue was found by our static-analysis tool.

A weakness has been identified in nemoTyrant manong up to 7c9e5228e133b9267ad3a415833bc9bb53193bb4. This impacts the function cache/del_cache/arr2sql of the file func.php. This manipulation causes sql injection. The attack may be initiated remotely. This product uses a rolling release model to deliver continuous updates. As a result, specific version information for affected or updated releases is not available. The reported GitHub issue was closed with the reason "completed". However, it was not possible to determine the PR or commit which could have fixed this issue.

A security flaw has been discovered in THU-MIG yoloe up to 40cd606cabdbe2b566d6f14a6b162c89206e9a1b. This affects the function eval of the file ultralytics/nn/autobackend.py of the component AutoBackend Model Loading. The manipulation of the argument imgsz/names/kpt_shape results in improper neutralization of directives in dynamically evaluated code. The attack requires a local approach. The exploit has been released to the public and may be used for attacks. This product does not use versioning. This is why information about affected and unaffected releases are unavailable. The project was informed of the problem early through an issue report but has not responded yet.

Missing Authorization vulnerability in Cozy Vision Technologies Pvt. Ltd. SMS Alert Order Notifications sms-alert allows Exploiting Incorrectly Configured Access Control Security Levels.This issue affects SMS Alert Order Notifications: from n/a through 4.0.1.

Coder before 2.34.7 contains an IP spoofing vulnerability in the ExtractRealIPAddress middleware that trusts the leftmost, client-supplied X-Forwarded-For value instead of the client IP appended by a reverse proxy. Attackers can send forged X-Forwarded-For values through appending proxies to bypass per-IP rate limits on login, one-time passcode, and password validation endpoints, enabling brute-force attacks, and to falsify IP addresses recorded in audit logs.

Coder before 2.29.17, 2.30.0 before 2.32.7, 2.33.0 before 2.33.8, and 2.34.0 before 2.34.2 contains a user enumeration vulnerability because userpassword.Compare() substitutes a placeholder hash derived from the string "hunter2" when a stored password hash is empty. Unauthenticated attackers can submit logins with the password "hunter2" and distinguish HTTP 403 from 401 responses to enumerate valid accounts and reveal the authentication provider of SSO-only users.

Coder before 2.29.17, 2.30.0 before 2.32.7, 2.33.0 before 2.33.8, and 2.34.0 before 2.34.2 contains a stored HTML injection vulnerability because the ApplicationName and LogoURL appearance settings are rendered into HTML output without sufficient escaping. Attackers with the Owner role can store HTML markup in these settings that renders in the Coder dashboard and in SMTP notification emails sent to other deployment users.

Coder from 2.0.0 before 2.34.8 contains an open redirect vulnerability in handleAPIKeySmuggling that allows attackers to redirect users externally via unsanitized r.URL.Path values. Attackers can craft links on trusted workspace app subdomains with paths beginning with double slashes, which become scheme-relative redirects to attacker sites for phishing.

Coder from 2.26.0 before 2.34.8 contains an incorrect authorization flaw in the GET /api/v2/workspaces/{id}/acl endpoint, which checks only workspace read access and then fetches group members using an elevated system context. Authenticated users granted workspace use access can query the endpoint to harvest group members' emails, login types, status, and last-seen and creation timestamps.

Coder from 2.30.0 before 2.34.8 contains an authorization bypass vulnerability in the provisioner daemon DownloadFile gRPC handler that allows authenticated provisioner daemons to download other organizations' cached Terraform module archives. Attackers with an org-scoped provisioner key and a known file UUID can retrieve module source code exposing infrastructure topology or embedded secrets.

Coder from 2.0.0 before 2.34.8 contains an incorrect authorization vulnerability in the acl_allow rule of coderd/rbac/policy.rego, which does not verify organization membership for per-user ACL entries, and organization member removal does not scrub those entries. Authenticated users removed from an organization can keep accessing previously granted org-scoped resources such as templates and workspaces via the API.

Coder before 2.29.20, 2.33.0 before 2.33.12, 2.34.0 before 2.34.8, and 2.35.0 before 2.35.4 contains an improper hostname validation flaw in GetWorkspaceProxyByHostname whose SIMILAR TO pattern performs a prefix match, so any domain that is a string prefix of a workspace-proxy access URL is trusted as a proxy. Attackers owning such a domain can lure an authenticated victim to a crafted /api/v2/applications/auth-redirect link, capture the redirected application_connect API key, and replay it to access the victim's workspace apps.

Coder from 2.10.0 before 2.34.8 has an unauthenticated agent debug HTTP server on 127.0.0.1:2113 whose /debug/manifest handler returns the full agent manifest, including template-provided environment variable values. A lower-privileged Unix user or process in the same workspace can query this endpoint to read credentials such as cloud keys or registry tokens.

Fleet before 4.83.0 contains a denial of service vulnerability that allows unauthenticated attackers to exhaust server memory by sending gzip-compressed request bodies. Attackers can send small, highly compressed requests with Content-Encoding: gzip to unauthenticated endpoints that expand during decoding, crashing the entire Fleet instance.

Fleet before 4.89.0 contains an unbounded recursion vulnerability in Apple MDM enrollment property list parsing that allows unauthenticated attackers to crash the server. Attackers can send a crafted binary plist payload of about 150 bytes to the enrollment endpoints, triggering exponential allocation or infinite recursion that exhausts CPU and memory.

Vikunja from 2.2.0 before 2.7.0 contains a permissive CORS configuration that trusts every localhost and 127.0.0.1 port with credentials, even when service.publicurl is set. Attackers controlling a page on any localhost port can send a credentialed request to the token refresh endpoint and read the returned bearer JWT to take over the logged-in user's account.

Vikunja 0.13.0 before 2.7.0 contains an incorrect authorization vulnerability that allows project members with Write permission to delete admin-tier link shares because the delete permission check reads an unloaded share object. Attackers can send DELETE requests to the v1 or v2 projects shares endpoints with sequential share IDs to revoke admin links and invalidate existing share sessions.

Vikunja 2.6.0 contains a broken access control flaw in getProjectAccessForUser (pkg/models/project_access.go), which resolves a user's effective project permission as the maximum over the project tree, silently overriding explicit lower-permission shares on sub-projects. A collaborator with write access on a parent project but read-only access to a child project can modify the child project's tasks and content.