CVE Feed

In the Linux kernel, the following vulnerability has been resolved: i2c: imx: Cancel hrtimer before clearing slave pointer In i2c_imx_unreg_slave(), the slave pointer is set to NULL after disabling interrupts. However, a pending interrupt might already have started the hrtimer (i2c_imx_slave_timeout) before the pointer was cleared. If the hrtimer fires after i2c_imx->slave is set to NULL, the timer callback i2c_imx_slave_finish_op() will call i2c_imx_slave_event() with a NULL slave pointer, which results in a use-after-free / NULL pointer dereference. Fix by canceling the hrtimer and waiting for it to complete after disabling interrupts, before clearing the slave pointer.

In the Linux kernel, the following vulnerability has been resolved: gpio: pch: use raw_spinlock_t for the register lock pch_irq_type() is registered as the irq_chip .irq_set_type callback and takes chip->spinlock with spin_lock_irqsave(). This callback is reached from __setup_irq() -> __irq_set_trigger() -> chip->irq_set_type() while the caller holds desc->lock, a raw_spinlock_t, with hardirqs disabled. That context is not sleepable, but on PREEMPT_RT a regular spinlock_t is an rtmutex-backed sleeping lock, so acquiring it there is invalid. This was confirmed on a PREEMPT_RT kernel with lockdep (PROVE_RAW_LOCK_NESTING and DEBUG_ATOMIC_SLEEP). A grounded PoC mirrored pch_irq_type()'s locking and drove it through the real genirq carrier irq_set_irq_type() -> __irq_set_trigger() -> chip->irq_set_type(), i.e. the same __irq_set_trigger() edge that __setup_irq() takes for a requested IRQ. With the original spin_lock_irqsave() edge lockdep reported an invalid wait context, immediately followed by: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 95, name: insmod hardirqs last disabled at (3784): _raw_spin_lock_irqsave+0x4f/0x60 rt_spin_lock+0x3a/0x1c0 repro_irq_set_type+0x64/0xa0 [pch_repro] __irq_set_trigger+0x69/0x140 irq_set_irq_type+0x78/0xd0 Switching the mirrored lock to raw_spinlock_t made both splats go away. Convert the register lock to raw_spinlock_t. The same lock also serializes the GPIO direction/value callbacks and the suspend/resume register save/restore, but all of those critical sections only perform MMIO register accesses (ioread32()/iowrite32()) and irq_set_handler_locked(); none of them contain sleepable operations. Keeping this register lock non-sleeping is therefore appropriate for the irqchip callbacks and does not change the GPIO-side locking contract. This is the same class of issue and fix as recently addressed for other GPIO controllers, e.g. commit 286533cb14a3 ("gpio: sch: use raw_spinlock_t in the irq startup path") and commit 90f0109019e6 ("gpio: eic-sprd: use raw_spinlock_t in the irq startup path").

In the Linux kernel, the following vulnerability has been resolved: s390/zcrypt: Close speculative mem read possibility The domain value is extracted from a given CCA or EP11 ioctl struct when a CPRB is about to be sent. Thus this is a user controlled value. Under some special conditions (custom device node used, administrative load) this value is used as an array index after bounds checking, but without speculation barrier. Add the missing array_index_nospec() call to prevent speculative execution where this domain value is used.

In the Linux kernel, the following vulnerability has been resolved: scsi: scsi_debug: Fix REPORT ZONES alloc_len underflow OOB write resp_report_zones() sizes the reply buffer from the CDB allocation length. The v3 fix rounds alloc_len up with ALIGN() before deriving the descriptor count: rep_max_zones = (ALIGN((u64)alloc_len, RZONES_DESC_HD) - RZONES_DESC_HD) >> ilog2(RZONES_DESC_HD); arr_len = (u64)RZONES_DESC_HD * (rep_max_zones + 1); For alloc_len in 0xFFFFFFC1..0xFFFFFFFF, ALIGN() rounds up to 0x100000000, so arr_len is 4 GB. On 32-bit, kzalloc()'s size_t is 32-bit and truncates 0x100000000 to 0; kzalloc(0) returns ZERO_SIZE_PTR, which passes the !arr check, and desc = arr + 64 is then dereferenced in the loop -> out-of-bounds write / panic. Clamp rep_max_zones to devip->nr_zones. The loop already stops at sdebug_capacity (after nr_zones zones), so a report can never hold more than nr_zones descriptors; the clamp does not change the report, it only bounds arr_len to (nr_zones + 1) * RZONES_DESC_HD, a real device property that can never reach 0x100000000.

In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: reject a flag character as the field delimiter The registration string starts with a user chosen delimiter that separates the individual fields. So that the field parsers terminate even on a truncated string create_entry() pads the buffer with that same delimiter: memset(buf + count, del, 8); Most fields are scanned for the delimiter with strchr()/scanarg() and happily stop on the padding. The flags field is different: instead of scanning for the delimiter check_special_flags() consumes the flag characters 'P', 'O', 'C' and 'F' and stops at the first byte that is none of them, relying on the trailing delimiter to end the scan. If the delimiter is itself a flag character the padding no longer acts as a terminator. The scan swallows all eight padding bytes and keeps reading past the end of the allocation until it hits a byte that is not a flag character. For example registering PaPEPPxPPiP with 'P' as the delimiter (name "a", type extension, magic "x", interpreter "i", empty flags) leaves the flag scan running off the end of the buffer. The registration is rejected in the end because the parser does not stop exactly at buf + count, but only after the out of bounds read has already happened. With an unlucky allocation layout the scan can walk into an unmapped page; under KASAN it is reported as a slab out of bounds read. binfmt_misc mounts are available to unprivileged users in a user namespace so the read is reachable without privileges. Reject a delimiter that is one of the flag characters up front. Such a registration was always rejected anyway, only after the out of bounds read, so no valid registration string changes meaning.

In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: don't let an 'F' entry pin its own instance An entry registered with 'F' opens its interpreter at registration time and holds that file until the entry is freed. Any entry nobody removes by hand only gets closed once the binfmt_misc superblock is shut down. If the interpreter lives on a mount that keeps that superblock alive the two pin each other: binfmt_misc sb -> inode -> entry -> interp_file -> vfsmount -> binfmt_misc sb TL;DR the file is never closed. Once the mount namespace is gone there is nothing left to unregister through either. There are two ways to trigger this bug: - Point the interpreter at the instance itself. Its files are regular files owned by the mounter and both bm_get_inode() and simple_fill_super() leave i_op at empty_iops. So notify_change() falls back to simple_setattr() and chmod +x works. We never set SB_I_NOEXEC and so open_exec() accepts it. - Use the instance as an overlayfs lower layer. The overlay superblock holds a clone_private_mount() of every layer until it is destroyed and that clone is in no namespace. So umount_tree() never reaches it. That's a DoS. And it isn't only the superblock that leaks. It pins the user namespace it was mounted in, so every iteration permanently eats one of the caller's user namespace charges. So let's just do the sane thing. SB_I_NOEXEC makes open_exec() fail on the instance's own files and s_stack_depth makes overlayfs reject the layer before it ever takes a clone. That also covers the ecryptfs and fuse passthrough variants. What 'F' promises is unchanged. The stable tag is narrower than the Fixes tags on purpose. Before sandboxed mounts this needed global root against the single instance everyone shares, and the change doesn't apply to those trees anyway. Note that SB_I_NODEV is implicitly raised for userns mounts but raise it explicitly here as well.

In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: don't leak the user namespace when the mount fails bm_get_tree() takes a reference to the user namespace and hands it to get_tree_keyed() as the sget key. sget_fc() moves that reference into sb->s_fs_info and clears fc->s_fs_info, so from that point on the superblock owns it and bm_free() doesn't see it anymore. The superblock drops it in ->put_super(). But generic_shutdown_super() only calls ->put_super() from inside the if (sb->s_root) branch, so nothing releases it when bm_fill_super() fails: - The kzalloc_obj() failure leaves s_root NULL and the whole branch is skipped. - A simple_fill_super() failure in the file loop leaves s_root set, but s_op still points at simple_super_operations, which has no ->put_super(). bm_fill_super() installs s_ops only once simple_fill_super() returned success, and installing it earlier wouldn't help either because simple_fill_super() overwrites s_op. Either way vfs_get_super() calls deactivate_locked_super() and the reference is gone for good. binfmt_misc mounts are available in a user namespace and both the inode and the dentry cache are SLAB_ACCOUNT, so an unprivileged caller under a tight memory cgroup can fail simple_fill_super() on demand and leak one user namespace per attempt. Drop the reference in ->kill_sb() instead, which runs unconditionally, the same way nfsd and rpc_pipefs release their keyed s_fs_info. That also stops ->put_super() from clearing s_fs_info while the superblock is still on @fs_supers. generic_shutdown_super() leaves it there on purpose so that sget_fc() keeps finding it until kill_sb() has run, but a NULL s_fs_info makes test_keyed_super() miss it, so a concurrent mount for the same user namespace skips the grab_super() wait and creates a second superblock for a namespace that is still being torn down.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: fix use-after-free in ump_to_endpoint() create_midi2_ump() registers a card-owned snd_ump_endpoint and stores a back-pointer to its per-interface snd_usb_midi2_ump object in ump->private_data, but it never installs an ump->private_free hook and never clears that pointer. If a later step of snd_usb_midi_v2_create() fails, its error path calls free_all_midi2_umps(), which kfree()s the snd_usb_midi2_ump object while the already-registered endpoint keeps pointing at it. The created /dev/snd/umpC*D* node stays exposed, so the first operation of any UMP open, ump_to_endpoint(), dereferences the dangling ump->private_data and reads rmidi->eps[dir] out of freed memory. A malicious USB MIDI 2.0 device that makes creation fail after the endpoint is registered can thus trigger a slab use-after-free read on a subsequent open of the UMP node. Clear the endpoint's back-pointer before freeing the object, and let ump_to_endpoint() tolerate a NULL private_data so the open/close/trigger callbacks fail cleanly (their callers already handle a NULL endpoint) instead of dereferencing a stale pointer. Discovered by XBOW, triaged by Baul Lee <[email protected]>

In the Linux kernel, the following vulnerability has been resolved: ALSA: seq: Fix division by zero in initialize_timer() A userspace-driven ALSA timer (SND_UTIMER) lets an unprivileged user set the backing snd_timer's hardware resolution to an arbitrary 64-bit value via SNDRV_TIMER_IOCTL_CREATE. snd_utimer_create() only rejects zero. When such a timer is bound to a sequencer queue, initialize_timer() computes the tick period as tmr->ticks = 1000000000 / (r * freq); where r is that user-controlled resolution and freq is the sequencer update rate in Hz, clamped to MIN_FREQUENCY..MAX_FREQUENCY (10..6250). A resolution of 2^63 makes the 64-bit product r * freq wrap to zero for any even freq, including DEFAULT_FREQUENCY (1000), so the division faults with a divide-by-zero. The division runs under tmr->lock with interrupts disabled, so the oops leaves the spinlock held and hangs the CPU. It is reachable by an unprivileged user with access to /dev/snd/timer and /dev/snd/seq. Oops: divide error: 0000 [#1] SMP KASAN PTI CPU: 7 UID: 1000 PID: 456 Comm: alsa_seq_utimer Not tainted 7.2.0-rc4+ RIP: 0010:initialize_timer.constprop.0+0x20a/0x2d0 snd_seq_timer_start+0x15e/0x2b0 snd_seq_control_queue+0x56f/0xba0 snd_seq_write+0x3e0/0x730 Reject an overflowing product with check_mul_overflow() and fall back to a single tick, which also avoids feeding a wrapped-but-nonzero divisor (e.g. 2^63 * 1000 mod 2^64 == 0, or other resolutions wrapping to a small value) into the period computation.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: HIDP: validate numbered report payloads When hidp_get_raw_report() waits for a numbered report, hidp_process_data() compares the expected report number with skb->data[0]. A connected HIDP peer can reply with only a DATA transaction header, leaving the skb empty after the header is removed. KMSAN reports an uninitialized-value use in hidp_session_run(), with the value originating in __alloc_skb() through vhci_write(). The transaction header checks remove the empty-frame reports, but this report remains until the payload check is added. The comparison can also consume a peer-controlled byte beyond the declared L2CAP PDU. A DATA | FEATURE response followed by an extra 0x01 byte made the current code accept that byte as report ID 1 and complete HIDIOCGFEATURE with a zero-byte result. With this change the malformed response is rejected with -EIO, while a subsequent valid response still succeeds. Require a payload byte before comparing a numbered report ID. Unnumbered reports continue to accept an empty payload.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: Fix advertising data UAFs hci_find_adv_instance() returns an adv_info pointer that is valid only while hdev->lock is held. The advertising command-sync paths perform instance lookups without that lock and, in some cases, retain the pointer while waiting for a controller response. An advertising termination event can therefore interleave as follows: hci_cmd_sync_work hci_rx_work hci_find_adv_instance() __hci_cmd_sync_status() wait for controller reply hci_dev_lock() hci_remove_adv_instance() kfree(adv) adv->scan_rsp_changed = false KASAN reported: BUG: KASAN: slab-use-after-free in hci_set_ext_scan_rsp_data_sync+0x2e1/0x300 Write of size 1 at addr ffff88810a45d21d by task kworker/u17:0/88 Workqueue: hci0 hci_cmd_sync_work Call Trace: hci_set_ext_scan_rsp_data_sync+0x2e1/0x300 hci_schedule_adv_instance_sync+0x390/0x4c0 hci_cmd_sync_work+0x173/0x300 Allocated by task 87: hci_add_adv_instance+0x538/0xac0 add_advertising+0x885/0x1160 Freed by task 89: kfree+0x131/0x3c0 hci_remove_adv_instance+0x1d8/0x3b0 hci_le_ext_adv_term_evt+0x17b/0x730 Protect the instance lookup and payload construction in the extended advertising, scan response, and periodic advertising data paths. Snapshot the advertising parameters under hdev->lock, but release the lock before waiting for the controller. Clear advertising-data dirty bits before issuing their commands and restore them after a failure using a fresh lookup. Likewise, update the reported transmit power through a fresh lookup after the parameter command completes. No adv_info pointer then survives an HCI command wait.

In the Linux kernel, the following vulnerability has been resolved: iommu/iommufd: Fix IOPF group ownership UAF iopf_group_alloc() links each last-page IOPF group into the generic IOPF pending list before invoking the domain fault handler. iommufd_fault_iopf_handler() also queued an accepted group in the IOMMUFD deliver list without removing it from the generic pending list. When detach or HWPT replacement drops the device's IOPF reference count to zero, an IOMMU driver may call iopf_queue_remove_device(). That function responds to and frees groups through the generic pending list without removing the same groups from IOMMUFD's deliver list or response xarray. A later read, response, or cleanup can then access the freed group and cause a UAF. Fix this by dequeuing an accepted group from the generic pending list before IOMMUFD queues it for userspace response. Make iopf_group_response() send a response regardless of pending-list membership, so the dequeued group can still be completed by IOMMUFD.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Cancel delayed I/O APIC EOI handling before destroying vCPUs Cancel (and flush) the I/O APIC's delayed EOI handling work during the "pre VM destroy" phase, before vCPUs are destroyed, as processing the EOI broadcast will inject another IRQ if the line is asserted, i.e. will try to deliver an IRQ to the target vCPU(s). Canceling the work after vCPUs are destroyed leads to UAF if the delayed work is processed after vCPUs are destroyed. BUG: KASAN: slab-use-after-free in __kvm_irq_delivery_to_apic_fast+0x9bf/0xa20 arch/x86/kvm/lapic.c:1250 Read of size 8 at addr ffff8880499abea0 by task kworker/1:2/1218 CPU: 1 UID: 0 PID: 1218 Comm: kworker/1:2 Not tainted 7.1.0-rc7 #5 PREEMPT(lazy) Hardware name: QEMU Ubuntu 25.10 PC v2 (i440FX + PIIX, + 10.1 machine, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: events kvm_ioapic_eoi_inject_work Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 dump_stack_lvl+0x100/0x190 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 print_report+0x139/0x4ad mm/kasan/report.c:482 kasan_report+0xe4/0x1d0 mm/kasan/report.c:595 __kvm_irq_delivery_to_apic_fast+0x9bf/0xa20 arch/x86/kvm/lapic.c:1250 __kvm_irq_delivery_to_apic+0xd8/0xbf0 arch/x86/kvm/lapic.c:1345 kvm_irq_delivery_to_apic arch/x86/kvm/lapic.h:129 ioapic_service+0x308/0x590 arch/x86/kvm/ioapic.c:492 kvm_ioapic_eoi_inject_work+0x13c/0x190 arch/x86/kvm/ioapic.c:532 process_one_work+0xa59/0x19a0 kernel/workqueue.c:3314 process_scheduled_works kernel/workqueue.c:3397 worker_thread+0x5eb/0xe50 kernel/workqueue.c:3478 kthread+0x370/0x450 kernel/kthread.c:436 ret_from_fork+0x72b/0xd30 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> Note, the VM is unreachable once kvm_destroy_vm() starts, and scheduling new work via kvm_ioapic_send_eoi() can only be done via KVM_RUN, i.e. requires a live vCPU. Alternatively, KVM could simply destroy the I/O APIC during the "pre" phase of VM destruction, but that gets more than a bit sketchy as KVM expects the I/O APIC to exist if ioapic_in_kernel() is true, and nested virtualization in particular has a bad habit of touching VM-scope state during vCPU destruction. E.g. attempting to free the PIC during the pre phase would lead to a NULL pointer dereference in kvm_cpu_has_extint(), and it's not hard to imagine the I/O APIC having a similar flaw.

In the Linux kernel, the following vulnerability has been resolved: riscv: mm: Fix out-of-bounds page-table walk during memory hot-remove remove_pud_mapping() and remove_p4d_mapping() obtain a child table base with pud_offset(p4dp, 0) and p4d_offset(pgd, 0), then add the index for addr. RISC-V folds page-table levels at runtime. When a level is folded, its offset helper returns the parent entry itself, but the index can still be nonzero. Adding it walks past the parent table. Sv48 folds P4D, while Sv39 folds both P4D and PUD, so memory hot-remove can descend into unrelated memory and pass an invalid page to __free_pages(). This can trigger: kernel BUG at include/linux/mm.h:1810! VM_BUG_ON_PAGE(page_ref_count(page) == 0) arch_remove_memory+0x1e/0x5c try_remove_memory+0x15e/0x200 remove_memory+0x24/0x3c Only add the index when the corresponding page-table level is enabled, matching p4d_offset() and pud_offset().

In the Linux kernel, the following vulnerability has been resolved: scsi: mpi3mr: Fix potential deadlock in mpi3mr_fault_uevent_emit mpi3mr_fault_uevent_emit() runs from the fault watchdog and reset paths where host I/O may already be blocked. GFP_KERNEL allocations here, both the local kzalloc_obj() and the ones inside kobject_uevent_env() itself, can trigger reclaim that waits on that blocked I/O and deadlock. Use memalloc_noio_save()/restore() to cover the whole call instead of just the local allocation.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_conn: hold conn reference in abort_conn_sync() There is theoretical UAF if the conn is freed while the hci_sync task is running. Hold refcount to avoid that.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btintel: Validate length before parsing diagnostics TLV btintel_diagnostics() accesses tlv->val[0] without first validating that the diagnostics VSE is long enough to contain that field, so may cause reading data beyond the received frame. Fix by validating the length before access.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: ISO: fix refcounting of iso_conn iso_conn_del() and iso_chan_del() have a race that results to double-put of iso_conn: [Task hdev->workqueue] [Task 2] iso_conn_del iso_chan_del iso_conn_hold_unless_zero iso_conn_lock iso_conn_lock conn->sk = NULL iso_conn_unlock sk = iso_sock_hold(conn) <---------´ if (!sk) iso_conn_put iso_conn_put iso_conn_put /* UAF */ The extra put for !sk in iso_conn_del() is currently required since failing iso_chan_add() may leave iso_conn not associated with any sk. Fix by having iso_pi(sk)->conn own refcount when non-NULL, so iso_conn_del does not need to put it. Adjust the iso_conn_add() refcounting so that conn is put if it does not get associated with an sk.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: ISO: lock sk in iso_sock_getname Accessing iso_pi(sk)->conn requires lock_sock, which is not held here. Fix by adding the lock/release.

In the Linux kernel, the following vulnerability has been resolved: netfs: Fix folio_queue ENOMEM in writeback by adding a mempool Fix the handling of folio_queue allocation failure in writeback by adding a mempool and passing in gfp_t flags to the rolling buffer functions that allocate memory, using the mempool if gfp != GFP_KERNEL. This is then extended upwards and the gfp to be used for a request is stored in the netfs_io_request struct and is then used for both requests and subrequests, eliminating the sleeping loops there. The failure caused: folio != NULL WARNING: fs/netfs/write_issue.c:603 at netfs_writepages+0x883/0xa10 fs/netfs/write_issue.c:603, CPU#3: syz.0.17/5919

In the Linux kernel, the following vulnerability has been resolved: hwmon: (nct6775-core) Prevent access to unsupported weight registers Sashiko reports: During initialization of the nct6116 chip, the driver sets data->pwm_num to 5. However, it assigns several NCT6106 register arrays (such as NCT6106_REG_WEIGHT_DUTY_STEP, NCT6106_REG_WEIGHT_TEMP_SEL, and NCT6106_REG_WEIGHT_TEMP_*) to data->REG_PWM and data->REG_WEIGHT_TEMP. These arrays only contain 3 elements. In nct6775_update_pwm(), the driver iterates up to data->pwm_num. If data->has_pwm has bits 3 or 4 set (which is structurally possible for nct6116), the loop attempts to read elements at index 3 and 4 from these 3-element arrays. This results in a global out-of-bounds read, which can be caught by KASAN. Furthermore, the driver uses these garbage out-of-bounds values as hardware register addresses for subsequent read and write operations. This leads to invalid hardware register access, potentially causing hardware misconfiguration or system crashes. The underlying problem is that the chip does support up to five fan control channels, but only the first three support weight control. Fix the problem by extending the affected weight register arrays with zeroed fields. The driver uses zeroed register addresses to determine if a register is supported or not, and skips accesses for unsupported registers.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (nzxt-smart2) DMA-align output buffer Sashiko reports: When send_output_report() calls hid_hw_output_report(), the underlying USB HID core calls usb_interrupt_msg() which maps this buffer directly for DMA. When the DMA mapping flushes or invalidates the cacheline, it will corrupt the adjacent variables (mutex, update_interval) that were modified concurrently by the CPU. This causes memory corruption due to cacheline sharing on non-coherent CPU architectures (such as ARM or MIPS). The DMA API debugging tool (CONFIG_DMA_API_DEBUG) will trigger runtime warnings for this violation. Any operation that triggers send_output_report() (like setting a fan speed or updating the interval) causes the USB DMA mapping. On systems with non-coherent caches, this structural bug causes immediate and deterministic memory corruption. Align the output buffer to ARCH_DMA_MINALIGN to fix the problem.

In the Linux kernel, the following vulnerability has been resolved: xsk: fix buffer leak in xsk_drop_skb() for AF_XDP multi-buffer Tx This patch is inspired by the check[1] from sashiko. It says when overflow happens, the address of cq to be published is invalid. Actually the severer thing is the whole process of publishing the address of cq in this particular case is not right: it should truely publish the address and advance the cached_prod in cq as long as it reads descriptors from txq. The following is the full analysis. xsk_drop_skb() is called in three places, which all discard a partially built multi-buffer skb: 1) xsk_build_skb() -EOVERFLOW error path: packet exceeds MAX_SKB_FRAGS 2) __xsk_generic_xmit() post-loop cleanup: an invalid descriptor in the TX ring prevents the partial packet from completing 3) xsk_release(): socket close while xs->skb holds an incomplete packet In all three cases, the TX descriptors for the already-processed frags have been consumed from the TX ring (xskq_cons_release), and CQ slots have been reserved. However, xsk_drop_skb() calls xsk_consume_skb() which cancels the CQ reservations via xsk_cq_cancel_locked(). Since the buffer addresses never appear in the completion queue, userspace permanently loses track of these buffers. Fix this by letting consume_skb() trigger the existing xsk_destruct_skb destructor, which already submits buffer addresses to the CQ via xsk_cq_submit_addr_locked(). Note that cancelling the descriptors back to the TX ring (via xskq_cons_cancel_n) is not a appropriate option because an oversized packet that always exceeds MAX_SKB_FRAGS would be retried indefinitely, which is an obviously deadlock bug in the TX path. Also move the desc->addr assignment in xsk_build_skb() above the overflow check so that the current descriptor's address is recorded before a potential -EOVERFLOW jump to free_err, consistent with the zerocopy path in xsk_build_skb_zerocopy(). [1]: https://lore.kernel.org/all/[email protected]/

In the Linux kernel, the following vulnerability has been resolved: xsk: reclaim invalid Tx descriptors in ZC batch path The zero-copy Tx batch parser stops when it encounters an invalid descriptor. If this happens after one or more continuation descriptors, the Tx consumer can be advanced past fragments that are neither submitted to the driver nor returned to userspace through the completion ring. A similar problem occurs when a packet exceeds xdp_zc_max_segs. The descriptors consumed up to the limit are released without completion, and the remaining continuation descriptors can subsequently be interpreted as the beginning of another packet. Parse Tx batches in packet units and distinguish descriptors belonging to complete valid packets from descriptors consumed while draining an invalid or oversized packet. Return the former to the driver and append the latter to the CQ address area so userspace can reclaim their UMEM frames. Treat a standalone invalid descriptor as a one-descriptor reclaim-only packet. Advancing the Tx-ring consumer releases the ring slot, but does not by itself return ownership of the referenced UMEM frame to userspace. Once draining starts, continue until the packet's end-of-packet descriptor is consumed. Preserve the drain state on the socket when EOP has not yet been supplied, so draining can continue during a later call. Leave incomplete but otherwise valid packets on the Tx ring. Shared-UMEM pools using multi-buffer Tx also need packet-framed parsing. Walk their Tx sockets one packet at a time, preserving the existing per-socket fairness scheme, instead of using the legacy one-descriptor fallback. Keep that fallback for shared pools that do not use multi-buffer Tx. Since the drain state is maintained per socket and both the singular and shared paths can resume an interrupted drain, changing the socket list from singular to shared requires no special bind-time transition. CQ entries are positional, and drivers may complete only part of the Tx work returned by xsk_tx_peek_release_desc_batch(). Therefore, reclaim-only entries cannot be published immediately when earlier driver-visible descriptors are still outstanding. Track the number of driver-visible CQ entries preceding the reclaim entries. Let xsk_tx_completed() publish partial hardware Tx completions, and publish the reclaim entries only after every earlier Tx descriptor has completed. Complete a reclaim-only batch immediately when there is no driver-visible work in front of it, and prevent another Tx batch from being appended while reclaim entries remain pending. Also cap batch processing by the size of the pool's temporary descriptor array, as Tx rings belonging to sockets sharing a UMEM may have different sizes. This ensures that every invalid Tx descriptor consumed by the ZC batch path is either submitted to the driver as part of a valid packet or returned to userspace without violating CQ completion ordering.

In the Linux kernel, the following vulnerability has been resolved: xsk: drain continuation descs after overflow in xsk_build_skb() Fix generic xmit path multi-buffer logic when packets are either too big (count of descriptors exceed MAX_SKB_FRAGS) or an invalid descriptor is included in fragmented packet. Introduce xdp_sock::drain_cont and act upon this flag - when it is set, keep on consuming descriptors from AF_XDP Tx ring and put them directly onto Cq. Previously these descriptors were silently lost and could never be reached again.

In the Linux kernel, the following vulnerability has been resolved: scsi: libiscsi_tcp: Bound SCSI Response data segment to the connection buffer iscsi_tcp_hdr_dissect() receives the data segment of several PDU types into the fixed-size conn->data buffer, which is allocated for ISCSI_DEF_MAX_RECV_SEG_LEN (8192) bytes. For the LOGIN_RSP, TEXT_RSP, REJECT and ASYNC_EVENT opcodes the dissect path already rejects a PDU whose DataSegmentLength exceeds that buffer. The SCSI Command Response (ISCSI_OP_SCSI_CMD_RSP) path also copies its data segment (sense/response data) into conn->data via iscsi_tcp_data_recv_prep(), but it does so without the same check. The only upstream bound on in.datalen is conn->max_recv_dlength, the initiator's advertised MaxRecvDataSegmentLength, which is commonly negotiated well above 8192 (open-iscsi defaults to 262144). A target that returns a SCSI Response with a DataSegmentLength between 8193 and max_recv_dlength therefore overflows the 8192-byte conn->data buffer. Once the same bound applies, ISCSI_OP_SCSI_CMD_RSP is handled exactly like those responses: bound the data segment, receive it into conn->data when present, and otherwise complete the PDU with no data. Fold the opcode into that case group rather than duplicating the check.

In the Linux kernel, the following vulnerability has been resolved: btrfs: skip global block reserve accounting for rescue mounts [BUG] Mounting with rescue=ibadroots after corrupting the block group tree root triggers a NULL pointer dereference: BUG: kernel NULL pointer dereference, address: 0000000000000100 RIP: 0010:btrfs_update_global_block_rsv+0x9d/0x1c0 [btrfs] Call Trace: fill_dummy_bgs+0xd4/0x120 [btrfs] open_ctree+0xc6e/0x1ca0 [btrfs] btrfs_get_tree+0x50d/0xa40 [btrfs] The same crash occurs with a corrupted raid stripe tree root, via btrfs_read_block_groups() instead of fill_dummy_bgs(). [CAUSE] With rescue=ibadroots, btrfs_read_roots() allows the mount to continue when either root cannot be read, leaving the corresponding root pointer NULL while its on-disk feature bit remains set. btrfs_update_global_block_rsv() then dereferences the missing root based on the feature bit alone. [FIX] Rescue mounts are fully read-only and cannot start transactions, so the global reserve is never consumed. Under btrfs_is_full_ro(), mark the reserve as full and return before performing the accounting. And since we need to check if the fs is mount fully RO, export fs_is_full_ro() as btrfs_is_full_ro(), and move it to fs.h. [ Squash the fs_is_full_ro() export commit into this one. ]

In the Linux kernel, the following vulnerability has been resolved: net/sched: sch_dualpi2: Do not call qdisc_tree_reduce_backlog during peek before restoring qlen Whenever dualpi2 drops packets during peek, it calls qdisc_tree_reduce_backlog. An issue arises because it calls qdisc_tree_reduce_backlog before it reincrements the qlen. If qlen drops to zero, but peek returns an skb, the parent's qlen_notify callback will be executed even though dualpi2 still has 1 packet on the queue and, thus, mistakenly deactivates the parent's class which leads to a null-ptr-deref: [ 101.427314][ T599] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000009: 0000 [#1] SMP KASAN NOPTI [ 101.427755][ T599] KASAN: null-ptr-deref in range [0x0000000000000048-0x000000000000004f] [ 101.428048][ T599] CPU: 2 UID: 0 PID: 599 Comm: ping Not tainted 7.1.0-rc5-00284-gbce53c430ed7 #102 PREEMPT(full) [ 101.428400][ T599] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 101.428608][ T599] RIP: 0010:qfq_dequeue (net/sched/sch_qfq.c:1150) sch_qfq [ 101.428821][ T599] Code: 00 fc ff df 80 3c 02 00 0f 85 46 0c 00 00 4c 8d 73 48 48 89 9d b8 02 00 00 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 ea 03 <80> 3c 02 00 0f 85 2d 0c 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b All code [ 101.429348][ T599] RSP: 0018:ffff8881110df4f0 EFLAGS: 00010216 [ 101.429541][ T599] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: dffffc0000000000 [ 101.429763][ T599] RDX: 0000000000000009 RSI: 00000024c0000000 RDI: ffff88811436c2b0 [ 101.429985][ T599] RBP: ffff88811436c000 R08: ffff88811436c280 R09: 1ffff11021277523 [ 101.430206][ T599] R10: 1ffff11021277526 R11: 1ffff11021277527 R12: 00000024c0000000 [ 101.430423][ T599] R13: ffff88811436c2b8 R14: 0000000000000048 R15: 0000000020000000 [ 101.430642][ T599] FS: 00007f61813e1c40(0000) GS:ffff8881691ef000(0000) knlGS:0000000000000000 [ 101.430913][ T599] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 101.431100][ T599] CR2: 00005651650850a8 CR3: 000000010ca0b000 CR4: 0000000000750ef0 [ 101.431320][ T599] PKRU: 55555554 [ 101.431433][ T599] Call Trace: [ 101.431544][ T599] <TASK> [ 101.431628][ T599] __qdisc_run (net/sched/sch_generic.c:322 net/sched/sch_generic.c:427 net/sched/sch_generic.c:445) [ 101.431792][ T599] ? dev_qdisc_enqueue (./include/trace/events/qdisc.h:49 (discriminator 22) net/core/dev.c:4176 (discriminator 22)) [ 101.431941][ T599] __dev_queue_xmit (./include/net/pkt_sched.h:120 ./include/net/pkt_sched.h:117 net/core/dev.c:4292 net/core/dev.c:4831) Fix this by only calling qdisc_tree_reduce_backlog in peek after the qlen is restored.

In the Linux kernel, the following vulnerability has been resolved: ASoC: tegra: tegra210_ahub: Validate written enum value tegra_ahub_put_value_enum() reads e->values[item[0]] before checking whether item[0] is within the enum item range. The existing check therefore happens too late to prevent an out-of-range read of the values array. Move the check before the array access.

In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Fix FRMR aging push to queue error flow Aging pools with pinned handles requires moving handles from the active queue to a non-empty inactive queue that might fail on new page allocation, we are currently not handling the fault and leaking any mkey that fails the push. Fix by Introducing push_queue_to_queue_locked() that fills the destination's partial tail page from the source and then splices the remaining source pages onto the destination, performing no allocation. Replace the per-handle move loop in age_pinned_pool() and the open-coded splice in pool_aging_work() with calls to the helper. As the helper cannot fail under memory pressure, removing a class of GFP_ATOMIC allocations under the pool lock and simplifying the error flow.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7925: validate skb length in testmode query In mt7925_tm_query(), the response skb from mt76_mcu_send_and_get_msg() is used in a memcpy without validating its length: memcpy(evt_resp, skb->data + 8, MT7925_EVT_RSP_LEN); where MT7925_EVT_RSP_LEN is 512. If the firmware returns a response shorter than 520 bytes (8 + 512), this reads beyond the skb data buffer. The over-read data is then returned to userspace via nla_put() in mt7925_testmode_dump(). Add a length check before the memcpy to ensure the skb contains sufficient data.

In the Linux kernel, the following vulnerability has been resolved: fbdev: sm501fb: Fix buffer errors in OF binding code The code that gets the frame buffer mode from OF has 'use after free', 'buffer overrun' and memory leaks. info->edid_data isn't free if the probe functions fail or if pd->def_mode is set. If both the CRT and PANEL are enabled info->edid_data is used after being freed and is freed twice. The string returned by of_get_property(np, "mode", &len) is just written over either the static "640x480-16@60" or the module parameter string without any regard for the length (which is most likely longer). Use kstrump() for the OF mode and free everything before freeing 'info.

In the Linux kernel, the following vulnerability has been resolved: ocfs2/dlm: require a ref for locking_state debugfs open debug_lockres_open() copies inode->i_private into struct debug_lockres and debug_lockres_release() later drops that pointer with dlm_put(). That only works if open successfully pins the struct dlm_ctxt. Today open calls dlm_grab(dlm) but ignores its return value. Once the last domain unregister has removed the context from dlm_domains, dlm_grab() returns NULL, yet open still stores the raw pointer and returns success. The later release path is outside the debugfs removal barrier, so it can call dlm_put() after dlm_free_ctxt_mem() has freed the context. KASAN reports this as a slab-use-after-free in dlm_put() called from debug_lockres_release(). Fail the open when dlm_grab() cannot acquire the reference and unwind the seq_file private state before returning. That keeps locking_state from handing out a file descriptor whose release path does not own the dlm_ctxt. The buggy scenario involves two paths, with each column showing the order within that path: locking_state debugfs open: last domain unregister: 1. debug_lockres_open() reads 1. dlm_unregister_domain() calls inode->i_private. dlm_complete_dlm_shutdown(). 2. debug_lockres_open() calls 2. shutdown removes the dlm_ctxt from dlm_grab(dlm) and gets NULL. dlm_domains. 3. open still stores the raw dlm 3. final teardown reaches pointer in dl->dl_ctxt and dlm_free_ctxt_mem() and frees it. returns success. 4. debug_lockres_release() later calls dlm_put(dl->dl_ctxt). Validation reproduced this kernel report: KASAN slab-use-after-free in dlm_put+0x82/0x200 RIP: 0033:0x7f4d349bc9e0 The buggy address belongs to the object at ffff888103a3c000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 816 bytes inside of freed 2048-byte region [ffff888103a3c000, ffff888103a3c800) Write of size 4 Call trace: dump_stack_lvl+0x66/0xa0 (?:?) print_report+0xd0/0x630 (?:?) dlm_put+0x82/0x200 (?:?) srso_alias_return_thunk+0x5/0xfbef5 (?:?) __virt_addr_valid+0x188/0x2f0 (?:?) kasan_report+0xe4/0x120 (?:?) kasan_check_range+0x105/0x1b0 (?:?) debug_lockres_release+0x53/0x80 (fs/ocfs2/dlm/dlmdebug.c:587) dlm_put+0x9/0x200 (?:?) debug_lockres_release+0x5c/0x80 (fs/ocfs2/dlm/dlmdebug.c:587) full_proxy_release+0x67/0x90 (?:?) __fput+0x1df/0x4b0 (?:?) do_raw_spin_lock+0x10f/0x1b0 (?:?) fput_close_sync+0xd2/0x170 (?:?) __x64_sys_close+0x55/0x90 (?:?) do_syscall_64+0x10c/0x640 (arch/x86/entry/syscall_64.c:87) irqentry_exit+0xac/0x6e0 (?:?) entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?) Freed by task stack: kasan_save_stack+0x33/0x60 (?:?) kasan_save_track+0x14/0x30 (?:?) kasan_save_free_info+0x3b/0x60 (?:?) __kasan_slab_free+0x5f/0x80 (?:?) kfree+0x30f/0x580 (?:?) dlm_put+0x1ce/0x200 (?:?) dlm_unregister_domain+0xf6/0xb30 (?:?) o2cb_cluster_disconnect+0x6b/0x90 (?:?) ocfs2_cluster_disconnect+0x41/0x70 (?:?) ocfs2_dlm_shutdown+0x1c4/0x220 (?:?) ocfs2_dismount_volume+0x38a/0x550 (?:?) generic_shutdown_super+0xc3/0x220 (?:?) kill_block_super+0x29/0x60 (?:?) deactivate_locked_super+0x66/0xe0 (?:?) cleanup_mnt+0x13d/0x210 (?:?) task_work_run+0xfa/0x170 (?:?) exit_to_user_mode_loop+0xd6/0x430 (?:?) do_syscall_64+0x3cb/0x640 (arch/x86/entry/syscall_64.c:87) entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?)

In the Linux kernel, the following vulnerability has been resolved: gpu: host1x: Fix iommu_map_sgtable() return value check Commit "iommu: return full error code from iommu_map_sg[_atomic]()" changed iommu_map_sgtable() to return an ssize_t and negative values in error cases, rather than a size_t and a zero. pin_job() also was incorrectly assigning to 'int', which could cause overflows into negative values. Update pin_job() to correctly check for errors from iommu_map_sgtable.

In the Linux kernel, the following vulnerability has been resolved: nvmet-tcp: fix page fragment cache leak in error path In nvmet_tcp_alloc_queue(), when a connection is closed during the allocation process (e.g., nvmet_tcp_set_queue_sock() returns -ENOTCONN), the error handling jumps to out_destroy_sq and then to out_ida_remove without draining the page fragment cache. Although nvmet_tcp_free_cmd() is called in some error paths to release individual page fragments, the underlying page cache reference held by queue->pf_cache is never released. The first allocation using pf_cache is the call to nvmet_tcp_alloc_cmd() for queue->connect, which happens after ida_alloc() returns successfully. This results in a page leak each time a connection fails during allocation, which could lead to memory exhaustion over time if connections are repeatedly opened and closed. Fix this by calling page_frag_cache_drain() before freeing the queue structure in the out_ida_remove label.

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix devx subscribe-event unwind NULL dereference MLX5_IB_METHOD_DEVX_SUBSCRIBE_EVENT() links event_sub into sub_list before initializing the fields used by the shared error path. If eventfd_ctx_fdget() then fails, the unwind path dereferences event_sub->ev_file in uverbs_uobject_put() and calls subscribe_event_xa_dealloc() with an unset xa_key_level1. subscribe_event_xa_alloc() creates the XA entry exactly once for a given key_level1, on the first occurrence of that key. The unwind path must therefore call subscribe_event_xa_dealloc() exactly once for it as well. Enforce that by adding devx_key_in_sub_list() and calling subscribe_event_xa_dealloc() only when the last matching pending entry is being cleaned up.

In the Linux kernel, the following vulnerability has been resolved: evm: terminate and bound the evm_xattrs read buffer evm_read_xattrs() allocates size + 1 bytes, fills them from the list of enabled xattrs, and then passes strlen(temp) to simple_read_from_buffer(). When no configured xattrs are enabled, the fill loop stores nothing and temp[0] remains uninitialized, so strlen() reads beyond initialized memory. Explicitly terminate the buffer after allocation, use snprintf() for each formatted line, and pass the accumulated length, without risk of truncation, to simple_read_from_buffer().

In the Linux kernel, the following vulnerability has been resolved: drm/xe: Wait on external BO kernel fences in exec IOCTL Before arming a user job, xe_exec_ioctl() only added the VM's dma-resv KERNEL slot as a dependency. That slot covers rebinds and the kernel operations of the VM's private BOs, but not external BOs (bo->vm == NULL), which carry their kernel operations (evictions, moves, ...) in their own dma-resv KERNEL slot. The DMA_RESV_USAGE_KERNEL slot is the cross-driver contract for memory management operations that must complete before the BO or its backing store may be used: any accessor is required to wait on the KERNEL fences before touching the resv. By skipping the external BOs' KERNEL slots, the exec path violated that contract and could schedule a user job while a kernel operation on an external BO mapped by the VM was still in flight, racing against it and potentially reading or writing memory that was being moved. Replace the VM-only dependency with an iteration over every object locked by the exec, adding each object's KERNEL slot as a job dependency. This covers the VM resv (rebinds and private BOs) as well as every external BO, mirroring the drm_gpuvm_resv_add_fence() call that later publishes the job fence to the same set of objects. Long-running mode continues to skip this, as before. (cherry picked from commit a6b842acf3ddd1efc53a56de9260cfa718fb35e7)

In the Linux kernel, the following vulnerability has been resolved: drm/rockchip: dw_dp: Switch to drmm_kzalloc() Driver makes use of drmm_encoder_init() to initialize the encoder and automatically handle the cleanup by registering drm_encoder_cleanup() with drmm_add_action(). However, the internal structure containing the encoder part gets allocated with devm_kzalloc(), which happens while component_bind_all() is being called from Rockchip DRM driver. The component framework further ensures it is deallocated as part of releasing all the resources claimed during bind, which is triggered from component_unbind_all(). When the reference to the DRM device gets eventually dropped via drm_dev_put() in rockchip_drm_unbind(), drmm_encoder_alloc_release() attempts to access the now released encoder structure, leading to use-after-free. Ensure driver's internal structure is still reachable on encoder cleanup by switching from a device-managed allocation to a drm-managed one.

In the Linux kernel, the following vulnerability has been resolved: can: etas_es58x: es58x_read_bulk_callback(): fix RX buffer leak on URB resubmit failure es58x_read_bulk_callback() resubmits the RX URB after processing a received packet. If the resubmit succeeds, the URB remains anchored and will be handled by the normal RX path or by teardown. However, if usb_submit_urb() fails, the callback unanchors the URB and then returns directly. This skips the existing free_urb path, so the coherent transfer buffer allocated with usb_alloc_coherent() is not released. Reuse the existing free_urb path after a resubmit failure so that the RX coherent buffer is freed before leaving the callback.

In the Linux kernel, the following vulnerability has been resolved: can: peak_usb: add bounds check for USB channel index The channel control index ctrl_idx is derived from rx->len which comes directly from a device USB payload. The mask 0x0f allows values 0-15, but the array size of usb_if->dev[] is only 2. Values 2-15 cause heap out-of-bounds read, eventually causing kernel panic in the IRQ context. Add bounds checking for ctrl_idx before the array access in both pcan_usb_pro_handle_canmsg() and pcan_usb_pro_handle_error().

In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: do not update comments from kernel-side hash adds mtype_resize() copies comment pointers with memcpy(), not the comment objects themselves. During the window after an entry has been copied but before the table swap and backlog replay, the old table is still published for packet-side updates while the replacement-table entry already holds the same ip_set_comment_rcu pointer. If xt_SET --add-set ... --exist hits that old entry in this window, mtype_add() calls ip_set_init_comment() even though packet-side adds carry no comment payload. That call frees the shared comment through the old entry, so the replacement-table entry now holds a stale pointer. When the queued add is replayed on the new table, mtype_add() calls ip_set_init_comment() again and strlen() dereferences the stale pointer. Fix this in mtype_add() by skipping ip_set_init_comment() when ext->target marks a packet-side add. Userspace adds still update comments, while packet-side adds can no longer free comment storage shared with a resize copy.

In the Linux kernel, the following vulnerability has been resolved: dibs: fix use-after-free of dmb_node in loopback attach/detach/unregister dibs_lo_attach_dmb(), dibs_lo_detach_dmb() and dibs_lo_unregister_dmb() look up the dmb_node under dmb_ht_lock, drop the lock and only then operate on the node's refcount. Nothing keeps the node alive across that window: __dibs_lo_unregister_dmb() removes the node from the hash table under the write lock and immediately frees it. A concurrent final put can therefore free the node between the lookup and the refcount operation: CPU0 (attach) CPU1 (owner unregisters) read_lock_bh(&dmb_ht_lock) find dmb_node (refcnt == 1) read_unlock_bh(&dmb_ht_lock) refcount_dec_and_test() 1 -> 0 write_lock_bh(&dmb_ht_lock) hash_del(&dmb_node->list) write_unlock_bh(&dmb_ht_lock) kfree(dmb_node) refcount_inc_not_zero(&dmb_node->refcnt) <-- use-after-free The same window exists for the refcount_dec_and_test() calls in the detach and unregister paths. Close the race structurally by making hash table membership and the refcount transitions atomic with respect to each other: - Perform the final refcount_dec_and_test() and hash_del() in a single dmb_ht_lock write-side critical section, in both the unregister and the detach path. Freeing the node still happens after the lock is dropped, which is safe because a node whose refcount reached zero has left the hash table and can no longer be found. - This establishes the invariant that any node found in the hash table holds at least one reference, and that the final reference can only be dropped under the write lock. dibs_lo_attach_dmb() can thus take its reference with a plain refcount_inc() while still holding the read lock; refcount_inc_not_zero() is no longer needed. __dibs_lo_unregister_dmb() no longer touches the hash table and is renamed to dibs_lo_free_dmb() accordingly. Note: commit cc21191b584c ("dibs: Move data path to dibs layer") moved the code to its current location; the race was introduced earlier by commit c3a910f2380f ("net/smc: implement DMB-merged operations of loopback-ism"). Tested SMC-D via ISM and dibs loopback.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: HIDP: reject frames without a transaction header hidp_recv_ctrl_frame() and hidp_recv_intr_frame() read skb->data[0] before checking that the L2CAP SDU contains a transaction header. A connected HIDP peer can send an empty basic-mode SDU and make both paths use an uninitialized byte from skb tailroom. KMSAN reports the use in hidp_session_run(), with the uninitialized value originating in __alloc_skb() through vhci_write(). The control path produces two reports and the interrupt path produces one. The byte can also be controlled by a malformed lower-layer packet. If an HCI ACL packet contains an L2CAP PDU with a declared zero-length payload followed by an extra 0x15 byte, l2cap_recv_acldata() reduces skb->len to the declared PDU length before dispatch. The current HIDP path nevertheless consumes the extra byte as HIDP_TRANS_HID_CONTROL | HIDP_CTRL_VIRTUAL_CABLE_UNPLUG and terminates the HIDP session. With this change, the same packet is discarded and a subsequent feature report request succeeds. Pull the transaction header with skb_pull_data() and discard frames that do not contain it.

In the Linux kernel, the following vulnerability has been resolved: net: sxgbe: free TX rings on RX allocation failure When RX descriptor ring allocation fails, init_dma_desc_rings() only frees the partially allocated RX rings and returns. The TX rings that were allocated earlier in the same function are leaked. Rearrange error labels to clean up TX rings upon RX failures.

In the Linux kernel, the following vulnerability has been resolved: qede: sync udp_tunnel ports outside qede_lock in the recovery path A TX timeout on a qede NIC that has VXLAN/GENEVE tunnel ports configured wedges the rtnetlink control plane of the whole machine: NETDEV WATCHDOG: ens6f1 (qede): transmit queue 2 timed out 10226 ms [qede_tx_timeout:586(ens6f1)]TX timeout on queue 2! [qede_recovery_handler:2665(ens6f0)]Starting a recovery process The recovery path deadlocks on the driver's own mutex: qede_sp_task rtnl_lock() mutex_lock(&edev->qede_lock) <- taken qede_recovery_handler qede_load udp_tunnel_nic_reset_ntf __udp_tunnel_nic_device_sync info->sync_table == qede_udp_tunnel_sync mutex_lock(&edev->qede_lock) <- same task: deadlock The mutex is not recursive, so the kworker blocks on itself with rtnl_lock held, and neither lock is ever released. Every task that calls rtnl_lock() afterwards (ip, ovs-vswitchd, lldpad, IPv6 addrconf, sshd) blocks forever while the node still answers ping. In a vmcore from an affected production node rtnl_mutex.owner decodes to the very kworker blocked at the innermost mutex_lock() above. Re-sync the tunnel ports from qede_sp_task() after the internal lock is dropped, still under rtnl_lock as the udp_tunnel API requires. This mirrors qede_open(), which calls udp_tunnel_nic_reset_ntf() under rtnl without the internal lock. qede_recovery_handler() now returns whether it has successfully reloaded an open device, and the caller re-syncs the ports only in that case. This keeps the old gating exactly: a device that was down or a failed recovery returns false, as those paths never reached the udp_tunnel_nic_reset_ntf() call before either. This was the only user of the qede_lock()/qede_unlock() helpers, so remove them.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: hold conn in hci_connect_big_sync() callback There is theoretical UAF if the conn is freed while the hci_sync task is running. Hold refcount to avoid that. Handle NULL hcon, return 0 + do nothing to match the previous behavior.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (nct6775-core) Fix number of temperature registers for NCT6116 Unlike NCT6106, NCT6116 only has three temperature registers, and with it only three temperature source and temperature source configuration registers. The register addresses match those of NCT6106 and can be re-used. The code used a separate array to list the temperature source registers for NCT6116, but used the size of the NCT6106 register array to set the number of registers. The NCT6106 register array provides six addresses, while the temperature source register array for NCT6116 only provides three addresses. This causes a KASAN report. BUG: KASAN: global-out-of-bounds in nct6775_probe+0x936/0x46f0 [nct6775] Read of size 2 at addr ffffffffc19561a6 by task modprobe/954 ... Call Trace: dump_stack+0x7d/0xa7 print_address_description.constprop.0+0x1c/0x220 ? __kasan_kmalloc.constprop.0+0xc9/0xd0 ? __kmalloc_node_track_caller+0x194/0x5b0 ? nct6775_probe+0x936/0x46f0 [nct6775] ? nct6775_probe+0x936/0x46f0 [nct6775] ... Fix the problem by hard-coding the number of temperature and temperature configuration registers to three for NCT6116. Drop the unnecessary NCT6116_REG_TEMP_SOURCE array and re-use NCT6106_REG_TEMP_SOURCE.

In the Linux kernel, the following vulnerability has been resolved: net: udp_tunnel: fix memory leak in udp_tunnel_nic_unregister() syzbot reported a memory leak [1] in the UDP tunnel NIC offload code. When device registration fails (e.g. in register_netdevice()), netdev core unwinds by sending a single NETDEV_UNREGISTER notification. If work was queued during NETDEV_REGISTER (utn->work_pending is set), udp_tunnel_nic_unregister() returns early: if (utn->work_pending) return; Because failed registrations do not enter netdev_wait_allrefs_any(), no subsequent NETDEV_UNREGISTER rebroadcast will ever occur. As a result, the struct udp_tunnel_nic allocated in udp_tunnel_nic_alloc() is leaked permanently. Fix this by removing the early return. Instead, synchronously cancel any pending work with cancel_delayed_work_sync() before freeing @utn. To be able to call cancel_delayed_work_sync() while holding RTNL (the work also needs RTNL), switch udp_tunnel_nic_device_sync_work() to rtnl_trylock(). If RTNL is contended, requeue the work with a 1 jiffy delay (via queue_delayed_work()) to prevent high CPU contention while waiting for RTNL lock. The utn->work_pending bookkeeping is no longer needed and is removed, as the workqueue core already tracks the pending/running state of the work. [1] BUG: memory leak unreferenced object 0xffff888127d5f840 (size 96): comm "syz-executor", pid 5806, jiffies 4294942188 backtrace (crc 99fdb6c8): __kmalloc_noprof+0x3bf/0x550 udp_tunnel_nic_alloc net/ipv4/udp_tunnel_nic.c:756 [inline] udp_tunnel_nic_register net/ipv4/udp_tunnel_nic.c:833 [inline] udp_tunnel_nic_netdevice_event+0x804/0xab0 net/ipv4/udp_tunnel_nic.c:931 notifier_call_chain+0x59/0x160 kernel/notifier.c:85 call_netdevice_notifiers_info+0x7d/0xb0 net/core/dev.c:2250 register_netdevice+0xc10/0xeb0 net/core/dev.c:11478

In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: fix deadlock between metadata writeback and transaction commit When writing out metadata extent buffers in a zoned filesystem, btree_writepages() holds fs_info->zoned_meta_io_lock across the whole writeback loop, including the call to btrfs_check_meta_write_pointer() -> check_bg_is_active(). For the tree-log block group, check_bg_is_active() may fail to activate the zone and fall back to btrfs_zone_finish_one_bg() to free an active zone. That path waits for the running transaction to commit while still holding zoned_meta_io_lock, but the committer needs that same lock to write out the tree extents, so the two tasks deadlock: Task A (kworker, metadata writeback) Task B (fsstress, transaction commit) ------------------------------------ ------------------------------------- wb_workfn() btrfs_commit_transaction(T) btree_writepages() btrfs_write_and_wait_transaction() btrfs_zoned_meta_io_lock() btrfs_write_marked_extents() btrfs_check_meta_write_pointer() btree_writepages() check_bg_is_active() [treelog_bg] btrfs_zoned_meta_io_lock() btrfs_zone_finish_one_bg() <blocks on zoned_meta_io_lock, btrfs_zone_finish() held by Task A> do_zone_finish() btrfs_inc_block_group_ro() btrfs_wait_for_commit() <blocks waiting for commit of transaction T, done by Task B> The sibling branch in check_bg_is_active() already drops zoned_meta_io_lock around do_zone_finish() for this exact reason. Do the same in the tree-log branch: release the lock around btrfs_zone_finish_one_bg() and re-acquire it afterwards. The lock only protects fs_info->active_{meta,system}_bg, which this branch does not touch, and ctx->zoned_bg keeps a reference to the block group across the unlock, so nothing is lost while the lock is dropped. This hang occasionally reproduces with fstests generic/475 on a zoned btrfs filesystem.