CVE Feed

In the Linux kernel, the following vulnerability has been resolved: irqchip/crossbar: Use correct index in crossbar_domain_free() crossbar_domain_free() resets the domain data and then uses the nulled out irq_data->hwirq member as index to reset the irq_map[] entry and to write the relevant crossbar register with a safe entry. That means it never frees the correct index and keeps the crossbar register connection to the source interrupt active. If it would not reset the domain data, then this would be even worse as irq_data->hwirq holds the source interrupt number, but both the map and register index need the corresponding GIC SPI number and not the source interrupt number. This might even result in an out of bounds access as the source interrupt number can be higher than the maximal index space. Fix this by using the GIC SPI index from the parent domain's irq_data.

In the Linux kernel, the following vulnerability has been resolved: tpm: tpm_tis_spi: Use wait_woken() in wait_for_tmp_stat() wait_event_interruptible_timeout() evaluates its condition after setting the current task state to TASK_INTERRUPTIBLE. With CONFIG_DEBUG_ATOMIC_SLEEP this triggers a warning when the IRQ wait path is used: tpm_tis_status() tpm_tis_spi_read_bytes() tpm_tis_spi_transfer_full() spi_bus_lock() mutex_lock() Address this with the following measures: 1. Call wait_tpm_stat_cond() only while tasking is running. 2. Use wait_woken() to wait for changes.

In the Linux kernel, the following vulnerability has been resolved: sunrpc: wait for in-flight TLS handshake callback when cancel loses race When wait_for_completion_interruptible_timeout() in svc_tcp_handshake() returns 0 (timeout) or -ERESTARTSYS (signal) and tls_handshake_cancel() then returns false, handshake_complete() has won the cancellation race: it has set HANDSHAKE_F_REQ_COMPLETED and is about to invoke svc_tcp_handshake_done(), but the callback's side effects on xpt_flags and on svsk->sk_handshake_done have not yet committed. The current code reads xpt_flags immediately to decide whether the session succeeded. Two races result. If the callback has executed set_bit(XPT_TLS_SESSION) but not yet clear_bit(XPT_HANDSHAKE), svc_tcp_handshake() sees a session, enqueues the transport, and returns. svc_xprt_received() then clears XPT_BUSY, a worker thread picks the transport up, the dispatcher in svc_handle_xprt() observes XPT_HANDSHAKE still set, and xpo_handshake is invoked a second time. That svc_tcp_handshake() calls init_completion(&svsk->sk_handshake_done) while the original callback concurrently calls complete_all() on it, corrupting the embedded swait_queue. If the callback has set HANDSHAKE_F_REQ_COMPLETED but not yet entered svc_tcp_handshake_done(), svc_tcp_handshake() reads XPT_TLS_SESSION as clear and tears the connection down even though the handshake is about to succeed. Wait for the callback to commit before inspecting xpt_flags. The completion is guaranteed to fire because handshake_complete() invokes svc_tcp_handshake_done() unconditionally once it has set HANDSHAKE_F_REQ_COMPLETED.

In the Linux kernel, the following vulnerability has been resolved: sunrpc: pin svc_xprt across the asynchronous TLS handshake callback svc_tcp_handshake() stores the raw svc_xprt pointer in tls_handshake_args.ta_data and submits the request through tls_server_hello_x509(). The handshake core takes only sock_hold(req->hr_sk); nothing references the embedding struct svc_sock that svc_tcp_handshake_done() reaches via container_of(). Two close races leave the in-flight callback writing through a freed svc_sock. svc_sock_free() calls tls_handshake_cancel() and discards its return value: a false return means handshake_complete() has already set HANDSHAKE_F_REQ_COMPLETED but hp_done() may not have finished, yet svc_sock_free() proceeds to kfree(svsk). The cancel-loser fall-through inside svc_tcp_handshake() itself produces the same window: when wait_for_completion_interruptible_timeout() returns <= 0 (timeout or signal) and tls_handshake_cancel() returns false, the function does not drain, returns, and svc_handle_xprt() calls svc_xprt_received(), which clears XPT_BUSY and can drop the last reference. A concurrent close then runs svc_sock_free() while svc_tcp_handshake_done() is still updating xpt_flags and walking svsk->sk_handshake_done. The corruption surfaces as set_bit/clear_bit RMW into the freed xpt_flags slab slot and as complete_all() walking and writing the freed wait_queue_head_t list embedded in sk_handshake_done -- a slab-corruption primitive, not a benign read. The path is reachable on any TLS-enabled NFS server whenever a connection close overlaps the tlshd downcall delivery window; the interruptible wait means signal delivery suffices, not just SVC_HANDSHAKE_TO expiry. Take svc_xprt_get(xprt) immediately before tls_server_hello_x509() so the in-flight callback owns its own reference. Release it on the two edges where the callback is guaranteed not to fire -- submission failure from tls_server_hello_x509() and a successful tls_handshake_cancel() -- and at the tail of svc_tcp_handshake_done() after complete_all(). [cel: rewrote commit message to describe the actual change]

In the Linux kernel, the following vulnerability has been resolved: nvdimm/btt: Free arena sub-allocations on discover_arenas() error path Memory allocated by btt_freelist_init(), btt_rtt_init(), and btt_maplocks_init() is not freed on some discover_arenas() error paths. This leaks memory when arena discovery fails. Add the missing kfree() calls to release the allocations before returning an error. [ as: commit message and log edits ]

In the Linux kernel, the following vulnerability has been resolved: remoteproc: qcom: Fix leak when custom dump_segments addition fails Free allocated minidump_region 'name' in qcom_add_minidump_segments() when failing before adding the region to 'dump_segments'. Otherwise, the 'name' is not tracked and is never freed by qcom_minidump_cleanup(). Return error when adding to 'dump_segments' fails.

In the Linux kernel, the following vulnerability has been resolved: KVM: nVMX: Move vTPR vs. TPR Threshold consistency check into "normal" checks Move the off-by-default consistency check for vmcs12.tpr_threshold vs. the virtual APIC vTPR into the "normal" controls checks, as waiting until KVM has loaded some amount of state is unnecessary and actively dangerous. Specifically, failure to unwind vmcs01.GUEST_CR3 to KVM's value when EPT is disabled results in KVM running L1 with an L1-controlled CR3, not with KVM's CR3! Alternatively, KVM could simply reset the MMU to force a reload of vmcs01.GUEST_CR3, but the _only_ reason the check was shoved into a "late" flow was to wait until the vmcs12 pages were retrieved. Rather than build up more crusty code, simply access vTPR using a regular guest memory access (performance isn't a concern). To circumvent the restrictions that led to KVM deferring nested_get_vmcs12_pages(), (a) use a VM-scoped API to read guest memory so that it always hits non-SMM memslots (for RSM), and (b) skip the check (since its off-by-default anyways) when the vCPU doesn't want to run, i.e. when userspace is restoring/stuffing state. If reading guest memory fails, simply skip the consistency check, as KVM's de facto ABI is that VMX instruction accesses to non-existent memory get PCI Bus Error semantics, where reads return 0xFFs. And if vTPR=0xFF, then the vTPR is guaranteed to be greater than or equal to TPR_THRESHOLD.

In the Linux kernel, the following vulnerability has been resolved: KVM: SEV: Do not allow intra-host migration/mirroring of SNP VMs The intra-host migration/mirroring feature is not fully implemented for SEV-SNP VMs. The proper migration requires additional SNP-specific state such as guest_req_mutex, guest_req_buf, and guest_resp_buf to be transferred or initialized on the destination. The SNP VM mirroring requires vmsa features to be copied as well otherwise ASID would be bound to SNP range while VM is detected as a SEV VM. Reject SNP source VMs in migration/mirroring until proper SNP state transfer is implemented. [sean: let lines poke past 80 chars, tag for stable]

In the Linux kernel, the following vulnerability has been resolved: regulator: core: regulator_lock_two() should test for EDEADLK not EDEADLOCK Compare against -EDEADLK, which is what ww_mutex_lock() actually returns and what every other deadlock check in this file already uses. Function regulator_lock_two() acquires two regulators via regulator_lock_nested() -> ww_mutex_lock(). On contention, ww_mutex_lock() returns -EDEADLK, which is the caller's signal to drop the lock it holds and retry the acquisition in the canonical order. However, regulator_lock_two() tests the return value against -EDEADLOCK rather than -EDEADLK. On most architectures, EDEADLK and EDEADLOCK are the same value, so the comparison happens to be correct and the bug is invisible. But on MIPS, SPARC, and PowerPC, those two errors have different values. The test is wrong: a genuine -EDEADLK backoff no longer matches -EDEADLOCK, so instead of unlocking and retrying, the code falls into WARN_ON(ret) and returns with only one of the two regulators locked. In practice, this is a bug only on MIPS, because the regulator core is not built or used on the other two platforms. In general, EDEADLK is preferred over EDEADLOCK for new code.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btmtk: fix URB leak in alloc_mtk_intr_urb error path When btmtk_isopkt_pad() fails, the previously allocated URB is not freed, leaking the urb structure. Add usb_free_urb() before returning the error.

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix undefined shift of user RQ WQE size set_rq_size() computes the RQ WQE size as "1 << rq_wqe_shift" based on the user-provided rq_wqe_shift, which is only checked to be greater than 32, so shifts of 32 are still accepted. A shift of 31 also overflows a signed integer, leading to undefined behavior. Use check_shl_overflow() to compute the RQ WQE size and reject any invalid values.

In the Linux kernel, the following vulnerability has been resolved: net: Stop leased rxq before uninstalling its memory provider netif_rxq_cleanup_unlease() tears down the memory provider that was installed on a physical RX queue through a netkit queue lease. It currently revokes the provider's DMA mappings before stopping the physical queue: __netif_mp_uninstall_rxq(virt_rxq, p); /* DMA unmap */ __netif_mp_close_rxq(phys_rxq->dev, rxq_idx, p); /* queue stop */ This inverts the ordering used by the regular teardown paths (normal device unregister and the io_uring zcrx close path), which stop the queue before revoking the provider's mappings. With the physical queue still live, its NAPI can keep consuming net_iov entries from the page_pool alloc cache after the __netif_mp_uninstall_rxq() has already cleared their dma_addr, opening a window for the device to DMA to a stale or zero address. Fix it by swapping the two calls so the queue is stopped (and its NAPI quiesced) before the provider is uninstalled. No functional regression was observed across repeated runs of the nk_qlease.py HW selftest, which exercises the lease teardown path; this was tested against fbnic QEMU emulation.

In the Linux kernel, the following vulnerability has been resolved: net: pfcp: allocate per-cpu tstats for PFCP netdevs PFCP uses dev_get_tstats64() as its ndo_get_stats64 callback, but pfcp_link_setup() does not request NETDEV_PCPU_STAT_TSTATS. The net core therefore leaves dev->tstats NULL for PFCP devices. Creating a PFCP rtnetlink device can immediately ask the new netdev for stats while building the RTM_NEWLINK notification. That reaches dev_get_tstats64() and dereferences the NULL dev->tstats pointer. Set pcpu_stat_type to NETDEV_PCPU_STAT_TSTATS during PFCP link setup so the net core allocates the storage expected by dev_get_tstats64().

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix potential deadlock in f2fs_balance_fs() When the f2fs filesystem space is nearly exhausted, we encounter deadlock issues as below: INFO: task A:1890 blocked for more than 120 seconds. Tainted: G O 6.12.41-g3fe07ddf05ab #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:A state:D stack:0 pid:1890 tgid:1626 ppid:1153 flags:0x00000204 Call trace: __switch_to+0xf4/0x158 __schedule+0x27c/0x908 schedule+0x3c/0x118 io_schedule+0x44/0x68 folio_wait_bit_common+0x174/0x370 folio_wait_bit+0x20/0x38 folio_wait_writeback+0x54/0xc8 truncate_inode_partial_folio+0x70/0x1e0 truncate_inode_pages_range+0x1b0/0x450 truncate_pagecache+0x54/0x88 f2fs_file_write_iter+0x3e8/0xb80 do_iter_readv_writev+0xf0/0x1e0 vfs_writev+0x138/0x2c8 do_writev+0x88/0x130 __arm64_sys_writev+0x28/0x40 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0xc8/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x30/0xf8 el0t_64_sync_handler+0x120/0x130 el0t_64_sync+0x190/0x198 INFO: task kworker/u8:11:2680853 blocked for more than 120 seconds. Tainted: G O 6.12.41-g3fe07ddf05ab #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u8:11 state:D stack:0 pid:2680853 tgid:2680853 ppid:2 flags:0x00000208 Workqueue: writeback wb_workfn (flush-254:0) Call trace: __switch_to+0xf4/0x158 __schedule+0x27c/0x908 schedule+0x3c/0x118 io_schedule+0x44/0x68 folio_wait_bit_common+0x174/0x370 __filemap_get_folio+0x214/0x348 pagecache_get_page+0x20/0x70 f2fs_get_read_data_page+0x150/0x3e8 f2fs_get_lock_data_page+0x2c/0x160 move_data_page+0x50/0x478 do_garbage_collect+0xd38/0x1528 f2fs_gc+0x240/0x7e0 f2fs_balance_fs+0x1a0/0x208 f2fs_write_single_data_page+0x6e4/0x730 f2fs_write_cache_pages+0x378/0x9b0 f2fs_write_data_pages+0x2e4/0x388 do_writepages+0x8c/0x2c8 __writeback_single_inode+0x4c/0x498 writeback_sb_inodes+0x234/0x4a8 __writeback_inodes_wb+0x58/0x118 wb_writeback+0x2f8/0x3c0 wb_workfn+0x2c4/0x508 process_one_work+0x180/0x408 worker_thread+0x258/0x368 kthread+0x118/0x128 ret_from_fork+0x10/0x200 INFO: task kworker/u8:8:2641297 blocked for more than 120 seconds. Tainted: G O 6.12.41-g3fe07ddf05ab #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u8:8 state:D stack:0 pid:2641297 tgid:2641297 ppid:2 flags:0x00000208 Workqueue: writeback wb_workfn (flush-254:0) Call trace: __switch_to+0xf4/0x158 __schedule+0x27c/0x908 rt_mutex_schedule+0x30/0x60 __rt_mutex_slowlock_locked.constprop.0+0x460/0x8a8 rwbase_write_lock+0x24c/0x378 down_write+0x1c/0x30 f2fs_balance_fs+0x184/0x208 f2fs_write_inode+0xf4/0x328 __writeback_single_inode+0x370/0x498 writeback_sb_inodes+0x234/0x4a8 __writeback_inodes_wb+0x58/0x118 wb_writeback+0x2f8/0x3c0 wb_workfn+0x2c4/0x508 process_one_work+0x180/0x408 worker_thread+0x258/0x368 kthread+0x118/0x128 ret_from_fork+0x10/0x20 INFO: task B:1902 blocked for more than 120 seconds. Tainted: G O 6.12.41-g3fe07ddf05ab #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:B state:D stack:0 pid:1902 tgid:1626 ppid:1153 flags:0x0000020c Call trace: __switch_to+0xf4/0x158 __schedule+0x27c/0x908 rt_mutex_schedule+0x30/0x60 __rt_mutex_slowlock_locked.constprop.0+0x460/0x8a8 rwbase_write_lock+0x24c/0x378 down_write+0x1c/0x30 f2fs_balance_fs+0x184/0x208 f2fs_map_blocks+0x94c/0x1110 f2fs_file_write_iter+0x228/0xb80 do_iter_readv_writev+0xf0/0x1e0 vfs_writev+0x138/0x2c8 do_writev+0x88/0x130 __arm64_sys_writev+0x28/0x40 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0xc8/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x30/0xf8 el0t_64_sync_handler+0x120/0x130 el0t_64_sync+0x190/0x198 INFO: task sync:2769849 blocked for more than 120 seconds. Tainted: G ---truncated---

In the Linux kernel, the following vulnerability has been resolved: liveupdate: validate session type before performing operation The sessions ioctls are not applicable to all session types. PRESERVE_FD is only applicable to outgoing sessions. RETRIEVE_FD and FINISH are only valid for incoming session. Calling a incoming ioctl on an outgoing session is invalid and can cause file handlers to run into unexpected errors. For example, a user can create a (outgoing) session, preserve a memfd, and then immediately do a retrieve without doing a kexec in between. This would result in memfd's retrieve handler to run. The handlers expects to be called from a post-kexec context, and will try to do a kho_restore_vmalloc() or kho_restore_folio() to try and restore memory. KHO catches this (thanks to KHO_PAGE_MAGIC) and returns an error, but since this is considered an internal error and KHO throws out a bunch of WARN()s. Associate a type with each ioctl op and validate the type in luo_session_ioctl() before dispatching the ioctl handler to make sure the op is being called for the right session type.

In the Linux kernel, the following vulnerability has been resolved: mmc: sdhci-esdhc-imx: disable irq during suspend to fix unhandled interrupt When using WIFI out-of-band wakeup, an "irq xxx: nobody cared" warning occurs. This happens because the usdhc interrupt is not disabled during system suspend when device_may_wakeup() returns false. The sequence of events leading to this issue: 1. System enters suspend without disabling usdhc interrupt (because device_may_wakeup() returns false for usdhc device) 2. WIFI out-of-band wakeup triggers system resume via GPIO interrupt 3. WIFI sends a Card interrupt before usdhc has fully resumed 4. usdhc is still in runtime suspend state and cannot handle the interrupt properly 5. The unhandled interrupt triggers "nobody cared" warning Fix this by unconditionally disabling the usdhc interrupt during suspend and re-enabling it during resume, regardless of the wakeup capability. This ensures no interrupts are processed during the suspend/resume transition.

In the Linux kernel, the following vulnerability has been resolved: mtd: rawnand: lpc32xx_slc: fail DMA transfer on completion timeout lpc32xx_xmit_dma() waits for the DMA completion callback but ignores wait_for_completion_timeout(). A timed out DMA transfer is therefore unmapped and reported as successful to the NAND read/write path. Return -ETIMEDOUT when the completion wait expires. Terminate the DMA channel before unmapping the scatterlist so the timed out transfer cannot continue to access the buffer after the error is returned.

In the Linux kernel, the following vulnerability has been resolved: scsi: elx: efct: Fix I/O leak on unsupported additional CDB efct_dispatch_fcp_cmd() allocates an efct_io before dispatching an unsolicited FCP command. If the command has an unsupported additional CDB, the function returns -EIO before handing the IO to the SCSI layer. Free the allocated IO before returning from this error path.

In the Linux kernel, the following vulnerability has been resolved: dm-integrity: fix leaking uninitialized kernel memory If hash size is less than device's tuple size, dm-integrity is supposed to zero the remaining space. There was a bug in the code that zeroing didn't work. This commit fixes it.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: bla: reacquire gw address after skb realloc The pskb_may_pull() called by batadv_bla_is_backbone_gw() could reallocate the buffer behind the skb. Variables which were pointing to the old buffer need to be reassigned to avoid an use-after-free.

In the Linux kernel, the following vulnerability has been resolved: hfsplus: Remove the duplicate attr inode dirty marking action Syzbot reported a null-ptr-deref in [1]. If the attributes file is not loaded during system mount, a trigger occurs [1] when setxattr is executed in userspace. Remove the first mark attr inode dirty operation. [1] KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f] Call Trace: hfsplus_setxattr+0x124/0x340 fs/hfsplus/xattr.c:555 hfsplus_trusted_setxattr+0x40/0x60 fs/hfsplus/xattr_trusted.c:30 __vfs_setxattr+0x43c/0x480 fs/xattr.c:218 __vfs_setxattr_noperm+0x12d/0x660 fs/xattr.c:252 vfs_setxattr+0x163/0x360 fs/xattr.c:339 do_setxattr fs/xattr.c:654 [inline]

In the Linux kernel, the following vulnerability has been resolved: nvme-apple: Prevent shared tags across queues on Apple A11 On Apple A11, tags of pending commands must be unique across the admin and IO queues, else the firmware crashes with "duplicate tag error for tag N", with N being the tag. Apply the existing workaround for M1 of reserving two tags for the admin queue to A11.

In the Linux kernel, the following vulnerability has been resolved: ublk: reset kernel-owned dev_info fields in ublk_ctrl_add_dev() ublk_ctrl_add_dev() memcpy()s the userspace ublksrv_ctrl_dev_info into ub->dev_info and then fixes up the fields the driver owns, but misses ->state and ->ublksrv_pid. A device added with ->state = UBLK_S_DEV_LIVE passes the "->state != UBLK_S_DEV_DEAD" test that ublk_stop_dev_unlocked() uses as its proxy for "a disk is attached", while ->ub_disk is still NULL, so DEL_DEV right after ADD_DEV oopses in del_gendisk(). UBLK_S_DEV_QUIESCED plus UBLK_F_USER_RECOVERY dies one step earlier, in ublk_force_abort_dev(). A poisoned ->state also gets START_USER_RECOVERY and the char device read/write path onto a device that was never started, and wedges START_DEV at -EEXIST. A poisoned ->ublksrv_pid just makes GET_DEV_INFO report an unrelated task as the ublk server. Reset both after the memcpy(), as ublk_detach_disk() does. Userspace only ever reads these back, so correcting them silently breaks nothing. ADD_DEV has copied ->state in unsanitized since ublk was merged, but back then it was harmless: the gendisk was allocated during ADD_DEV, and both teardown and the START_DEV -EEXIST check keyed off disk_live() rather than ->state. The oops became reachable once the disk allocation moved to START_DEV and those checks switched to ->state.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_meta_bridge: fix NFT_META_BRI_IIFPVID stack leak This needs to test for nonzero retval.

In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: Don't use test_bit() in lockless RCU readers in hash types Sashiko pointed out that there are a few lockless RCU readers using test_bit() which is a relaxed atomic operation and provides no memory barrier guarantees. Use test_bit_acquire() instead where the operation may run parallel with add/del/gc, i.e. is not one from the next cases - protected by region lock - in a set destroy phase - in a new/temporary set creation phase

In the Linux kernel, the following vulnerability has been resolved: can: bcm: defer rx_op deallocation to workqueue to fix thrtimer UAF Commit f1b4e32aca08 ("can: bcm: use call_rcu() instead of costly synchronize_rcu()") replaced synchronize_rcu() in bcm_delete_rx_op() with call_rcu() and introduced the RX_NO_AUTOTIMER flag. However, this flag check was omitted for thrtimer in the packet rx fast-path. During BCM RX operation teardown, a concurrent RCU reader (bcm_rx_handler) can race and re-arm thrtimer via bcm_rx_update_and_send() after call_rcu() has been scheduled. Once the RCU grace period elapses, bcm_op is freed. The subsequently firing thrtimer then dereferences the deallocated op, causing a UAF. Adding flag checks to the rx fast-path (bcm_rx_update_and_send) does not fully close the TOCTOU race and introduces latency for every CAN frame. Conversely, calling hrtimer_cancel() directly inside the RCU callback (softirq context) is fatal as hrtimer_cancel() can sleep, triggering a "scheduling while atomic" panic. Resolve this by deferring the timer cancellation and memory free to a dedicated unbound workqueue (bcm_wq). The RCU callback now queues a work item to bcm_wq, which safely cancels both timers and deallocates memory in sleepable process context. A dedicated workqueue is used to prevent system-wide WQ saturation and is cleanly flushed/destroyed on module unload to avoid rmmod page faults. Since the deferred work can now outlive the calling context by an unbounded amount, also take a reference on op->sk when it is assigned and drop it only once the deferred work has cancelled both timers, so a socket can no longer be freed out from under a still-armed timer whose callback (bcm_send_to_user()) dereferences op->sk.

In the Linux kernel, the following vulnerability has been resolved: fs/proc/task_mmu: fix make_uffd_wp_huge_pte() prot-update race Patch series "userfaultfd/pagemap: pre-existing fixes". These are pre-existing bug fixes that were carried at the front of the userfaultfd RWP working-set-tracking series up to v5 [1]. Per review feedback that fixes should not sit in the middle of a feature series, they are split out and sent on their own; the RWP series is reposted rebased on top of this. All six were flagged by the Sashiko AI review of the RWP series and carry independent of RWP, apply to mm-new directly, and carry Cc: stable@. 1: fs/proc/task_mmu: a missing huge_ptep_modify_prot_start() in make_uffd_wp_huge_pte() can lose hardware Dirty/Accessed updates when PAGEMAP_SCAN write-protects a hugetlb PTE. 2: fs/proc/task_mmu: pagemap_scan_hugetlb_entry() compares the range against HPAGE_SIZE rather than the hstate page size, so it never write-protects gigantic hugetlb pages. 3: fs/proc/task_mmu: PAGEMAP_SCAN with PM_SCAN_WP_MATCHING over an unpopulated hugetlb range self-deadlocks -- pagemap_scan_pte_hole() calls uffd_wp_range() while walk_hugetlb_range() holds the hugetlb vma lock for read, and hugetlb_change_protection() then takes it for write. Install the marker inline instead. 4: mm/huge_memory: change_non_present_huge_pmd() drops pmd_swp_uffd_wp on a device-private PMD permission downgrade, silently losing the uffd-wp marker. 5: userfaultfd: must_wait() applies pte_write() to a locklessly read PTE without checking pte_present(), so swap/migration entries decode random offset bits and a thread can stay parked on a stale fault. 6: userfaultfd: __VMA_UFFD_FLAGS feeds VMA_UFFD_MINOR_BIT (41) to mk_vma_flags() unconditionally, an out-of-bounds write into the single-word vma_flags_t on 32-bit. Build the mask from config-gated per-mode masks so an unavailable bit is never materialised. This patch (of 6): make_uffd_wp_huge_pte() arms the UFFD_WP bit on a present HugeTLB PTE by calling huge_ptep_modify_prot_commit() with a ptent snapshot that was fetched without the corresponding huge_ptep_modify_prot_start(). The start helper is what atomically clears the entry so the kernel-owned snapshot stays consistent until the commit; without it, the hardware may set Dirty or Accessed in the live PTE between the original read and the commit, and huge_ptep_modify_prot_commit() (whose generic implementation just calls set_huge_pte_at()) then writes the stale snapshot back over the live hardware bits, losing the update. The non-hugetlb sibling make_uffd_wp_pte() does this correctly via ptep_modify_prot_start() / ptep_modify_prot_commit(). Mirror that pattern for the present-PTE branch. The migration case stays as-is -- migration entries are non-present, so there's no hardware update to race against.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: nv: Drop bogus WARN for write to ZCR_EL2 It is entirely possible for a guest to write to the ZCR_EL2 sysreg alias while in a nested context, as it is expected if FEAT_NV2 is advertised to the L1 hypervisor. Get rid of the bogus WARN which, since the hyp vectors were installed at this point, has the effect of a hyp_panic...

In the Linux kernel, the following vulnerability has been resolved: iomap: guard io_size EOF trim against concurrent truncate underflow iomap: fix zero padding data issue in concurrent append writes changed ioend accounting so that io_size tracks only valid data within EOF. This trims io_size when a writeback range extends past end_pos: ioend->io_size += map_len; if (ioend->io_offset + ioend->io_size > end_pos) ioend->io_size = end_pos - ioend->io_offset; However, if end_pos ends up below ioend->io_offset, the subtraction becomes negative and is stored in size_t io_size, causing an unsigned wrap to a huge value. This can happen when writeback continues past byte-level EOF up to a block-aligned range, or when a concurrent truncate shrinks the file after end_pos was sampled in iomap_writeback_handle_eof(). A wrapped io_size can mislead append detection and corrupt completion-time size handling, since filesystem end_io paths consume io_size for decisions such as on-disk EOF updates and unwritten/COW completion ranges. Fix this by clamping io_size to zero when EOF has moved to or before the ioend start offset. This preserves the original intent of trimming io_size to valid in-EOF data while avoiding the underflow.

In the Linux kernel, the following vulnerability has been resolved: net/liquidio: drop cached VF pci_dev LUT The PF SR-IOV enable path caches VF pci_dev pointers in dpiring_to_vfpcidev_lut[] by iterating with pci_get_device(). Those entries do not own a reference, because the iterator drops the previous device reference on each step. The cached pointer is then dereferenced later when handling OCTEON_VF_FLR_REQUEST. Replace the cached VF mapping with runtime lookup on the mailbox DPI ring: derive the VF index from q_no, resolve the VF via exported PCI IOV helpers, validate it with the PF pointer and VF ID, then issue pcie_flr() and drop the reference with pci_dev_put(). Remove the unused VF lookup table initialization and cleanup.

In the Linux kernel, the following vulnerability has been resolved: crypto: cavium/cpt - fix DMA cleanup using wrong loop index The sg_cleanup error path used list[i] instead of list[j] when unmapping DMA buffers, leaking successfully mapped entries and repeatedly unmapping the failed one.

In the Linux kernel, the following vulnerability has been resolved: gpu: host1x: Fix device reference leak in host1x_device_parse_dt() error path After device_initialize(), the embedded struct device in struct host1x_device should be released through the device core with put_device(). In host1x_device_add(), if host1x_device_parse_dt() fails, the current error path frees the object directly with kfree(device). That bypasses the normal device lifetime handling and leaks the reference held on the embedded struct device. The issue was identified by a static analysis tool I developed and confirmed by manual review. Fix this by using put_device() in the host1x_device_parse_dt() failure path.

In the Linux kernel, the following vulnerability has been resolved: ntfs: validate index entries on reading Validate index entries immediately after reading an index root or index block from disk. This eliminates repeated checks in lookup and readdir, and reduce the risk of missing checks in those paths.

In the Linux kernel, the following vulnerability has been resolved: ntfs: not change 0-byte $DATA attribute to non-resident When ntfs_resident_attr_resize() cannot grow a resident attribute in place, it retries after converting other resident attributes to non-resident to free space in the MFT recrord. Do not select zero-length resident $DATA attributes for this conversion. fsck treats 0-byte non-resident $DATA attribute as corruptions.

In the Linux kernel, the following vulnerability has been resolved: ntfs: add bounds check before accessing EA entries in ntfs_ea_lookup and ntfs_listxattr, this verifies that there is enough space in the EA entry before accessing the next_entry_offset field of the EA entry.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: 6lowpan: hold L2CAP conn across debugfs control get_l2cap_conn() looks up an LE hci_conn under hdev protection, but then drops that protection before reading hcon->l2cap_data and before lowpan_control_write() later dereferences conn->hcon. A disconnect or device close can tear down the same L2CAP connection in that window. The buggy scenario involves two paths, with each column showing the order within that path: 6LoWPAN control write: HCI disconnect/device close: 1. get_l2cap_conn() finds hcon 1. hci_disconn_cfm() dispatches and hcon->l2cap_data. the L2CAP disconnect callback. 2. get_l2cap_conn() drops hdev 2. l2cap_conn_del() clears protection and returns conn. hcon->l2cap_data and drops the L2CAP connection reference. 3. lowpan_control_write() reads 3. hci_conn_del() removes and drops conn->hcon. the HCI connection. Take a reference to the L2CAP connection with l2cap_conn_hold_unless_zero() while hdev is still locked, and drop that reference after the debugfs command's last use of conn. This mirrors the existing L2CAP ACL receive-side handoff and keeps the connection dereferenceable after leaving hdev protection. Export the existing helper so the bluetooth_6lowpan module can use the same lifetime primitive. Validation reproduced this kernel report: BUG: KASAN: slab-use-after-free in lowpan_control_write+0x374/0x520 The buggy address belongs to the object at ffff888111b9d000 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 0 bytes inside of freed 1024-byte region [ffff888111b9d000, ffff888111b9d400) Read of size 8 Call trace: dump_stack_lvl+0x66/0xa0 print_report+0xce/0x5f0 lowpan_control_write+0x374/0x520 (net/bluetooth/6lowpan.c:1131) srso_alias_return_thunk+0x5/0xfbef5 __virt_addr_valid+0x19f/0x330 kasan_report+0xe0/0x110 __debugfs_file_get+0xf7/0x400 full_proxy_write+0x9e/0xd0 vfs_write+0x1b0/0x810 ksys_write+0xd2/0x170 dnotify_flush+0x32/0x220 do_syscall_64+0x115/0x6a0 (arch/x86/entry/syscall_64.c:87) entry_SYSCALL_64_after_hwframe+0x77/0x7f Allocated by task stack: kasan_save_stack+0x33/0x60 kasan_save_track+0x17/0x60 __kasan_kmalloc+0xaa/0xb0 l2cap_conn_add+0x45/0x520 l2cap_chan_connect+0xac6/0xd90 l2cap_sock_connect+0x216/0x350 __sys_connect+0x101/0x130 __x64_sys_connect+0x40/0x50 do_syscall_64+0x115/0x6a0 (arch/x86/entry/syscall_64.c:87) entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task stack: kasan_save_stack+0x33/0x60 kasan_save_track+0x17/0x60 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x5f/0x80 kfree+0x313/0x590 hci_conn_hash_flush+0xc0/0x140 hci_dev_close_sync+0x41a/0xb00 hci_dev_close+0x12f/0x160 hci_sock_ioctl+0x157/0x570 sock_do_ioctl+0xf7/0x210 sock_ioctl+0x32f/0x490 __x64_sys_ioctl+0xc7/0x110 do_syscall_64+0x115/0x6a0 (arch/x86/entry/syscall_64.c:87) entry_SYSCALL_64_after_hwframe+0x77/0x7f kasan_record_aux_stack+0xa7/0xc0 insert_work+0x32/0x100 __queue_work+0x262/0xa60 queue_work_on+0xad/0xb0 l2cap_connect_cfm+0x4ef/0x670 hci_le_remote_feat_complete_evt+0x247/0x430 hci_event_packet+0x360/0x6f0 hci_rx_work+0x2ae/0x7a0 process_one_work+0x4fd/0xbc0 worker_thread+0x2d8/0x570 kthread+0x1ad/0x1f0 ret_from_fork+0x3c9/0x540 ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: rtc: msc313: fix NULL deref in shared IRQ handler at probe msc313_rtc_probe() calls devm_request_irq() with IRQF_SHARED and &pdev->dev as the cookie, but platform_set_drvdata() is only called later after the clock setup. With a shared IRQ line, another device on the same line can trigger the handler in that window. The handler does dev_get_drvdata() on the cookie, gets NULL, and dereferences priv->rtc_base in interrupt context. Pass priv as the cookie directly so the handler reads it from dev_id without the lookup, removing the dependency on probe order.

In the Linux kernel, the following vulnerability has been resolved: net/sched: cls_flow: Dont expose folded kernel pointers The flow classifier falls back to addr_fold() for fields that are missing from packet headers. In map mode, userspace controls mask, xor, rshift, addend and divisor, and can observe the resulting classid through class statistics. This allows a tc classifier in a user/network namespace to recover the 32-bit folded value of skb->sk, skb_dst() or skb_nfct(). Align with standard kernel practices for pointer hashing and replace the XOR folding with a keyed siphash (which is cryptographically secure)

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: use the subframe length when parsing A-MSDU TDLS frames mwifiex_11n_dispatch_amsdu_pkt() splits an A-MSDU with ieee80211_amsdu_to_8023s() and walks the resulting subframes. For each subframe it passes the subframe data pointer to mwifiex_process_tdls_action_frame(), but pairs it with skb->len, the length of the A-MSDU parent, instead of rx_skb->len: rx_skb = __skb_dequeue(&list); rx_hdr = (struct rx_packet_hdr *)rx_skb->data; if (ISSUPP_TDLS_ENABLED(priv->adapter->fw_cap_info) && ntohs(rx_hdr->eth803_hdr.h_proto) == ETH_P_TDLS) { mwifiex_process_tdls_action_frame(priv, (u8 *)rx_hdr, skb->len); } The parent is not a valid description of that buffer, and may not be valid memory at all. ieee80211_amsdu_to_8023s() ends with if (!reuse_skb) dev_kfree_skb(skb); and it only sets reuse_skb when the parent is linear, is not a head_frag, and is being consumed as the *last* subframe. So when the parent does not qualify for reuse it has already been freed, and the read of skb->len is a use-after-free. When it is reused, skb->len is the length of the last subframe, applied to every earlier subframe, which over-states the buffer whenever an earlier subframe is shorter. The callee cannot absorb a wrong length, because it derives its own ceiling from the value it is given. Each frame type computes ies_len = len - sizeof(struct ethhdr) - TDLS_*_FIX_LEN; and the element walk is then bounded entirely against that ceiling, for (end = pos + ies_len; pos + 1 < end; pos += 2 + pos[1]) { u8 ie_len = pos[1]; if (pos + 2 + ie_len > end) break; so a too-large len moves end past the end of the subframe and the walk reads and copies beyond it. The A-MSDU layout is chosen by the sender, which makes the difference between the last subframe and a shorter earlier one remotely selectable. Reaching this requires TDLS support in firmware and the TDLS ethertype on the subframe. The other caller, mwifiex_process_rx_packet(), is correct: it passes a pointer and a length that describe the same region of the RX buffer. Pass rx_skb->len, the length of the subframe actually being parsed.

In the Linux kernel, the following vulnerability has been resolved: md/raid1,raid10: fix deadlock in read error recovery path raid1d and raid10d may resubmit a split md cloned bio while handling a read error. In this case, resubmitting the bio can lead to a deadlock if the array is suspended before md_handle_request() acquires an active_io reference via percpu_ref_tryget_live(). Since the cloned bio already holds an active_io reference, trying to acquire another reference via percpu_ref_tryget_live() can lead to a deadlock while the array is suspended. Fix this by using percpu_ref_get() for md cloned bios.

In the Linux kernel, the following vulnerability has been resolved: net: macb: drop in-flight Tx SKBs on close The MACB driver has since forever leaked the outgoing SKBs that have not yet been marked as completed. They live in queue->tx_skb which gets freed without remorse nor checking. macb_free_consistent() gets called in a few codepaths, but only close will trigger the added expressions. In macb_open() and macb_alloc_consistent() failure cases, queues' tx_skb just got allocated and are empty.

In the Linux kernel, the following vulnerability has been resolved: MIPS: DEC: Ensure 32-bit stack location for o32 prom_printf() In 64-bit configurations calling any firmware entry points from a kernel thread other than the initial one will result in a situation where the stack has been placed in the XKPHYS 64-bit memory segment. Consequently the stack pointer is no longer a 32-bit value and when the 32-bit firmware code called uses 32-bit ALU operations to manipulate the stack pointer, the calculated result is incorrect (in fact in the 64-bit MIPS ISA almost all 32-bit ALU operations will produce an unpredictable result when executed on 64-bit data) and control goes astray. This may happen when no final console driver has been enabled in the configuration and consequently the initial console continues being used late into bootstrap, or with an upcoming change that will switch the zs driver to use a platform device, which in turn will make the console handover happen only after other kernel threads have already been started, and the kernel will hang at: pid_max: default: 32768 minimum: 301 or somewhat later, but always before: cblist_init_generic: Setting adjustable number of callback queues. has been printed. It seems that only the prom_printf() entry point is affected. Of all the other entry points wired only rex_slot_address() and rex_gettcinfo() are called from a kernel thread other than the initial one, specifically kernel_init(), and they are leaf functions that do no business with the stack, having worked with no issue ever since 64-bit support was added for the platform back in 2002. To address this issue then, arrange for the stack to be switched in the o32 wrapper as required for prom_printf() only, by supplying call_o32() with a pointer to a chunk of initdata space, which is placed in the CKSEG0 32-bit compatibility segment, observing that prom_printf() is only called from console output handler and therefore with the console lock held, implying no need for this code to be reentrant. Other firmware entry points may be called with interrupts enabled and no lock held, and may therefore require that call_o32() be reentrant. They trigger no issue at this point and "if it ain't broke, don't fix it," so just leave them alone.

In the Linux kernel, the following vulnerability has been resolved: selinux: avoid sk_socket dereference in selinux_sctp_bind_connect() selinux_sctp_bind_connect() dereferences sk->sk_socket to pass a struct socket * to selinux_socket_bind() and selinux_socket_connect_helper(). However, when the hook is invoked from the ASCONF softirq path (sctp_process_asconf), there is no file reference guaranteeing that sk->sk_socket is non-NULL. The setsockopt callers (bindx, connectx, set_primary, sendmsg connect) hold a file reference and are not affected. Both selinux_socket_bind() and selinux_socket_connect_helper() immediately resolve sock->sk, never using the struct socket * for anything else. Refactor the inner logic into helpers that take a struct sock * directly so that selinux_sctp_bind_connect() never needs to touch sk->sk_socket at all.

In the Linux kernel, the following vulnerability has been resolved: usb: atm: ueagle-atm: wait for pre-firmware load in .disconnect() ueagle-atm uses the asynchronous request_firmware_nowait() in .probe(), but does not wait for its completion, not even in .disconnect(); so, if the device is unplugged meanwhile, its teardown runs concurrently with that. Even though this inconsistency is worth addressing on its own, it has also triggered several bug reports in syzbot over the years (some auto-closed) where the firmware sysfs fallback mechanism (CONFIG_FW_LOADER_USER_HELPER) creates a firmware subdirectory in the device directory during its removal, which might hit unexpected conditions in kernfs, apparently, depending at which point the add and remove operations raced. (See links.) The pattern is: usb ?-?: Direct firmware load for ueagle-atm/eagle?.fw failed with error -2 usb ?-?: Falling back to sysfs fallback for: ueagle-atm/eagle?.fw <ERROR> Call trace: ... kernfs_create_dir_ns sysfs_create_dir_ns create_dir kobject_add_internal kobject_add_varg kobject_add class_dir_create_and_add get_device_parent device_add fw_load_sysfs_fallback fw_load_from_user_helper firmware_fallback_sysfs _request_firmware request_firmware_work_func ... (Some variations are observed, after fw_load_sysfs_fallback(), e.g., [1].) While the kernfs side is being looked at, the ueagle-atm side can be fixed by waiting for the pre-firmware load in the .disconnect() handler. This change has a similar approach to previous work by Andrey Tsygunka [2] (wait_for_completion() in .disconnect()), but it is relatively different in design/implementation; using the Originally-by tag for credit assignment. This has been tested with: - synthetic reproducer to check the error path; - USB gadget (virtual device) to check the firmware upload path; - QEMU device emulator to check the device ID re-enumeration path; (The latter two were written by Claude; no other code/text in this commit.) Links (year first reported): 2025 https://syzbot.org/bug?extid=ce1e5a1b4e086b43e56d 2025 https://syzbot.org/bug?extid=9af8471255ac36e34fd4 2024 https://syzbot.org/bug?extid=306212936b13e520679d 2023 https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2 2022 https://syzbot.org/bug?extid=782984d6f1701b526edb 2021 https://syzbot.org/bug?id=f3f221579f4ef7e9691281f3c6f56c05f83e8490 2021 https://syzbot.org/bug?id=84d86f0d71394829df6fc53daf6642c045983881 2021 https://syzbot.org/bug?id=3302dc1c0e2b9c94f2e8edb404eabc9267bc6f90 [1] https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2 [2] https://lore.kernel.org/lkml/[email protected]/

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: fix permanently busy scans after multiple roam iterations In order for the firmware to sleep, the driver has to confirm a previously received sleep request. The normal sequence of evets goes like this: EVENT_SLEEP -> adapter->ps_state = PS_STATE_PRE_SLEEP -> sleep-confirm -> SLEEP -> EVENT_AWAKE -> AWAKE. Before sending the sleep-confirm command, the driver must make sure there are no commands either running or waiting to be completed. mwifiex_ret_802_11_associate() unconditionally sets ps_state = PS_STATE_AWAKE when it processes the association command response, outside of the normal powersave management flow. If EVENT_SLEEP arrives while the association command is in flight, ps_state is PRE_SLEEP when the association command response is parsed, and the forced AWAKE overwrites it. The deferred sleep-confirm is never sent. A subsequent scan_start command is correctly acknowledged, but the firmware doesn't generate scan_result events. The scan request never finishes, and additional requests from userspace fail with -EBUSY. After testing on both IW412 and W8997, I could only trigger the bug on the IW412 and observed the firmwares behave differently. On the IW412 the firmware still sends EVENT_SLEEP while the authentication / association process is ongoing. A W8997 under the same conditions seems to suppress power-save for the duration of the association, so PRE_SLEEP never coincided with the association response even after extended periods of testing using the loops described below (>12hours). On the IW412, the delay between commands that triggers an EVENT_SLEEP was empirically determined to be ~20ms. This delay can naturally occur when the driver is outputting debugging information (debug_mask = 0x00000037), in which situation the busy scans issue is repeatable while running "test 1)" as described below. If the delay between commands is less than ~20ms, the firmware stays awake and the issue was not reproducible running the same test. The host_mlme=false path also behaves differently. In this case, the entire authentication / association transaction is executed by one command (HostCmd_CMD_802_11_ASSOCIATE), and the firmware doesn't emit EVENT_SLEEP while the command is running. Remove the assignment so the ps_state is only manipulated in the paths that are related to powersave event handling and on the main workqueue for correct sleep confirmation. The following loop tests were performed (with debugging output enabled): 1) force roaming between two AP's, one 5GHz and one 2.4GHz, same SSID. Use wpa_cli to trigger the roaming behavior, sleep 2s between iterations. 2) force a disconnection to AP 1 and a connection to AP 2, test scan. Use wpa_cli to trigger the connection changes, sleep 2s between iterations. Each test ran in each device for at least 3 hours.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: validate extension-frame layout before RX Extension frames only have the extension header at the regular 802.11 header offset. The generic RX path can still reach helpers and interface dispatch code that read regular header address fields before unsupported extension subtypes are dropped. mac80211 currently only handles S1G beacon extension frames. Drop other extension subtypes before they can reach regular-header RX processing. For S1G beacons, linearize the SKB with the management-frame path and require the fixed S1G beacon header, including optional fixed fields indicated by frame control, before generic RX dispatch. Route S1G beacons through the station/default-link RX path without regular-header station lookup. Avoid regular-header address reads in the mac80211 RX paths that process S1G extension beacons, including accept-frame, duplicate-detection, address-copy, and MLO address-translation paths. Also make ieee80211_get_bssid() length-safe before returning the S1G source-address pointer.

In the Linux kernel, the following vulnerability has been resolved: riscv: Prevent NULL pointer dereference in machine_kexec_prepare() A NULL pointer dereference issue is noticed in riscv's machine_kexec_prepare(), where image->segment[i].buf might be NULL and copied unchecked. The NULL buf comes from ima_add_kexec_buffer(), where kbuf is added by kexec_add_buffer(), but kbuf.buffer is NULL, then it is copied without a check in machine_kexec_prepare(): kexec_file_load -> kimage_file_alloc_init() -> kimage_file_prepare_segments() -> ima_add_kexec_buffer() -> kexec_add_buffer() -> machine_kexec_prepare() -> memcpy() Address this by adding a check before the data copy attempt.

In the Linux kernel, the following vulnerability has been resolved: powerpc/uaccess: correct check for CONFIG_PPC_E500 in mask_user_address() mask_user_address() incorrectly checks for CONFIG_E500 instead of CONFIG_PPC_E500, causing mask_user_address_isel() to not be used on E500 hardware. Fix the check to use the correct name.

In the Linux kernel, the following vulnerability has been resolved: pmdomain: imx93-blk-ctrl: Extract PHY as shared domain for DSI/CSI The MIPI DSI and CSI domains share control bits for clock and reset, which can lead to incorrect behavior if one domain disables the shared resource while the other is still active. To fix the issue, introduce a shared MIPI PHY power domain to own the common resources and make DSI and CSI its subdomains. This ensures the shared bits are properly managed and not disabled while still in use.

In the Linux kernel, the following vulnerability has been resolved: cgroup/cpuset: rebind mm mempolicy to effective_mems, not mems_allowed Creating a child cpuset where cpuset.mems is never set leads to a div/0 when a VMA mempolicy with MPOL_F_RELATIVE_NODES rebinds in response to a CPU hotplug event. Reproduction steps: 1) Create a cgroup w/ cpuset controls (do not set cpuset.mems) 2) Move the task into the child cpuset 3) Create a VMA mempolicy for that task with MPOL_F_RELATIVE_NODES 4) unplug and hotplug a cpu echo 0 > /sys/devices/system/cpu/cpu1/online echo 1 > /sys/devices/system/cpu/cpu1/online 5) mempolicy rebind does a div/0 in mpol_relative_nodemask on the call to __nodes_fold() The cpuset code passes (cs->mems_allowed) which is not guaranteed to have nodes to the rebind routine. Use cs->effective_mems instead, which is guaranteed to have a non-empty nodemask once we reach that code path. [ david: add a comment, slightly rephrase description ]