CVE Feed

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to wait dio completion It should wait all existing dio write IOs before block removal, otherwise, previous direct write IO may overwrite data in the block which may be reused by other inode.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix out-of-bounds in dbNextAG() and diAlloc() In dbNextAG() , there is no check for the case where bmp->db_numag is greater or same than MAXAG due to a polluted image, which causes an out-of-bounds. Therefore, a bounds check should be added in dbMount(). And in dbNextAG(), a check for the case where agpref is greater than bmp->db_numag should be added, so an out-of-bounds exception should be prevented. Additionally, a check for the case where agno is greater or same than MAXAG should be added in diAlloc() to prevent out-of-bounds.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: remove unused C2H event ID RTW89_MAC_C2H_FUNC_READ_WOW_CAM to prevent out-of-bounds reading The handler of firmware C2H event RTW89_MAC_C2H_FUNC_READ_WOW_CAM isn't implemented, but driver expects number of handlers is NUM_OF_RTW89_MAC_C2H_FUNC_WOW causing out-of-bounds access. Fix it by removing ID. Addresses-Coverity-ID: 1598775 ("Out-of-bounds read")

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: use hweight16 to get correct tx antenna The chainmask is u16 so using hweight8 cannot get correct tx_ant. Without this patch, the tx_ant of band 2 would be -1 and lead to the following issue: BUG: KASAN: stack-out-of-bounds in mt7996_mcu_add_sta+0x12e0/0x16e0 [mt7996e]

In the Linux kernel, the following vulnerability has been resolved: RDMA/iwcm: Fix WARNING:at_kernel/workqueue.c:#check_flush_dependency In the commit aee2424246f9 ("RDMA/iwcm: Fix a use-after-free related to destroying CM IDs"), the function flush_workqueue is invoked to flush the work queue iwcm_wq. But at that time, the work queue iwcm_wq was created via the function alloc_ordered_workqueue without the flag WQ_MEM_RECLAIM. Because the current process is trying to flush the whole iwcm_wq, if iwcm_wq doesn't have the flag WQ_MEM_RECLAIM, verify that the current process is not reclaiming memory or running on a workqueue which doesn't have the flag WQ_MEM_RECLAIM as that can break forward-progress guarantee leading to a deadlock. The call trace is as below: [ 125.350876][ T1430] Call Trace: [ 125.356281][ T1430] <TASK> [ 125.361285][ T1430] ? __warn (kernel/panic.c:693) [ 125.367640][ T1430] ? check_flush_dependency (kernel/workqueue.c:3706 (discriminator 9)) [ 125.375689][ T1430] ? report_bug (lib/bug.c:180 lib/bug.c:219) [ 125.382505][ T1430] ? handle_bug (arch/x86/kernel/traps.c:239) [ 125.388987][ T1430] ? exc_invalid_op (arch/x86/kernel/traps.c:260 (discriminator 1)) [ 125.395831][ T1430] ? asm_exc_invalid_op (arch/x86/include/asm/idtentry.h:621) [ 125.403125][ T1430] ? check_flush_dependency (kernel/workqueue.c:3706 (discriminator 9)) [ 125.410984][ T1430] ? check_flush_dependency (kernel/workqueue.c:3706 (discriminator 9)) [ 125.418764][ T1430] __flush_workqueue (kernel/workqueue.c:3970) [ 125.426021][ T1430] ? __pfx___might_resched (kernel/sched/core.c:10151) [ 125.433431][ T1430] ? destroy_cm_id (drivers/infiniband/core/iwcm.c:375) iw_cm [ 125.441209][ T1430] ? __pfx___flush_workqueue (kernel/workqueue.c:3910) [ 125.473900][ T1430] ? _raw_spin_lock_irqsave (arch/x86/include/asm/atomic.h:107 include/linux/atomic/atomic-arch-fallback.h:2170 include/linux/atomic/atomic-instrumented.h:1302 include/asm-generic/qspinlock.h:111 include/linux/spinlock.h:187 include/linux/spinlock_api_smp.h:111 kernel/locking/spinlock.c:162) [ 125.473909][ T1430] ? __pfx__raw_spin_lock_irqsave (kernel/locking/spinlock.c:161) [ 125.482537][ T1430] _destroy_id (drivers/infiniband/core/cma.c:2044) rdma_cm [ 125.495072][ T1430] nvme_rdma_free_queue (drivers/nvme/host/rdma.c:656 drivers/nvme/host/rdma.c:650) nvme_rdma [ 125.505827][ T1430] nvme_rdma_reset_ctrl_work (drivers/nvme/host/rdma.c:2180) nvme_rdma [ 125.505831][ T1430] process_one_work (kernel/workqueue.c:3231) [ 125.515122][ T1430] worker_thread (kernel/workqueue.c:3306 kernel/workqueue.c:3393) [ 125.515127][ T1430] ? __pfx_worker_thread (kernel/workqueue.c:3339) [ 125.531837][ T1430] kthread (kernel/kthread.c:389) [ 125.539864][ T1430] ? __pfx_kthread (kernel/kthread.c:342) [ 125.550628][ T1430] ret_from_fork (arch/x86/kernel/process.c:147) [ 125.558840][ T1430] ? __pfx_kthread (kernel/kthread.c:342) [ 125.558844][ T1430] ret_from_fork_asm (arch/x86/entry/entry_64.S:257) [ 125.566487][ T1430] </TASK> [ 125.566488][ T1430] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs-clt: Reset cid to con_num - 1 to stay in bounds In the function init_conns(), after the create_con() and create_cm() for loop if something fails. In the cleanup for loop after the destroy tag, we access out of bound memory because cid is set to clt_path->s.con_num. This commits resets the cid to clt_path->s.con_num - 1, to stay in bounds in the cleanup loop later.

In the Linux kernel, the following vulnerability has been resolved: f2fs: get rid of online repaire on corrupted directory syzbot reports a f2fs bug as below: kernel BUG at fs/f2fs/inode.c:896! RIP: 0010:f2fs_evict_inode+0x1598/0x15c0 fs/f2fs/inode.c:896 Call Trace: evict+0x532/0x950 fs/inode.c:704 dispose_list fs/inode.c:747 [inline] evict_inodes+0x5f9/0x690 fs/inode.c:797 generic_shutdown_super+0x9d/0x2d0 fs/super.c:627 kill_block_super+0x44/0x90 fs/super.c:1696 kill_f2fs_super+0x344/0x690 fs/f2fs/super.c:4898 deactivate_locked_super+0xc4/0x130 fs/super.c:473 cleanup_mnt+0x41f/0x4b0 fs/namespace.c:1373 task_work_run+0x24f/0x310 kernel/task_work.c:228 ptrace_notify+0x2d2/0x380 kernel/signal.c:2402 ptrace_report_syscall include/linux/ptrace.h:415 [inline] ptrace_report_syscall_exit include/linux/ptrace.h:477 [inline] syscall_exit_work+0xc6/0x190 kernel/entry/common.c:173 syscall_exit_to_user_mode_prepare kernel/entry/common.c:200 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:205 [inline] syscall_exit_to_user_mode+0x279/0x370 kernel/entry/common.c:218 do_syscall_64+0x100/0x230 arch/x86/entry/common.c:89 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0010:f2fs_evict_inode+0x1598/0x15c0 fs/f2fs/inode.c:896 Online repaire on corrupted directory in f2fs_lookup() can generate dirty data/meta while racing w/ readonly remount, it may leave dirty inode after filesystem becomes readonly, however, checkpoint() will skips flushing dirty inode in a state of readonly mode, result in above panic. Let's get rid of online repaire in f2fs_lookup(), and leave the work to fsck.f2fs.

In the Linux kernel, the following vulnerability has been resolved: scsi: sd: Fix off-by-one error in sd_read_block_characteristics() Ff the device returns page 0xb1 with length 8 (happens with qemu v2.x, for example), sd_read_block_characteristics() may attempt an out-of-bounds memory access when accessing the zoned field at offset 8.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac8021: fix possible oob access in ieee80211_get_rate_duration Fix possible out-of-bound access in ieee80211_get_rate_duration routine as reported by the following UBSAN report: UBSAN: array-index-out-of-bounds in net/mac80211/airtime.c:455:47 index 15 is out of range for type 'u16 [12]' CPU: 2 PID: 217 Comm: kworker/u32:10 Not tainted 6.1.0-060100rc3-generic Hardware name: Acer Aspire TC-281/Aspire TC-281, BIOS R01-A2 07/18/2017 Workqueue: mt76 mt76u_tx_status_data [mt76_usb] Call Trace: <TASK> show_stack+0x4e/0x61 dump_stack_lvl+0x4a/0x6f dump_stack+0x10/0x18 ubsan_epilogue+0x9/0x43 __ubsan_handle_out_of_bounds.cold+0x42/0x47 ieee80211_get_rate_duration.constprop.0+0x22f/0x2a0 [mac80211] ? ieee80211_tx_status_ext+0x32e/0x640 [mac80211] ieee80211_calc_rx_airtime+0xda/0x120 [mac80211] ieee80211_calc_tx_airtime+0xb4/0x100 [mac80211] mt76x02_send_tx_status+0x266/0x480 [mt76x02_lib] mt76x02_tx_status_data+0x52/0x80 [mt76x02_lib] mt76u_tx_status_data+0x67/0xd0 [mt76_usb] process_one_work+0x225/0x400 worker_thread+0x50/0x3e0 ? process_one_work+0x400/0x400 kthread+0xe9/0x110 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x22/0x30

In the Linux kernel, the following vulnerability has been resolved: tipc: re-fetch skb cb after tipc_msg_validate As the call trace shows, the original skb was freed in tipc_msg_validate(), and dereferencing the old skb cb would cause an use-after-free crash. BUG: KASAN: use-after-free in tipc_crypto_rcv_complete+0x1835/0x2240 [tipc] Call Trace: <IRQ> tipc_crypto_rcv_complete+0x1835/0x2240 [tipc] tipc_crypto_rcv+0xd32/0x1ec0 [tipc] tipc_rcv+0x744/0x1150 [tipc] ... Allocated by task 47078: kmem_cache_alloc_node+0x158/0x4d0 __alloc_skb+0x1c1/0x270 tipc_buf_acquire+0x1e/0xe0 [tipc] tipc_msg_create+0x33/0x1c0 [tipc] tipc_link_build_proto_msg+0x38a/0x2100 [tipc] tipc_link_timeout+0x8b8/0xef0 [tipc] tipc_node_timeout+0x2a1/0x960 [tipc] call_timer_fn+0x2d/0x1c0 ... Freed by task 47078: tipc_msg_validate+0x7b/0x440 [tipc] tipc_crypto_rcv_complete+0x4b5/0x2240 [tipc] tipc_crypto_rcv+0xd32/0x1ec0 [tipc] tipc_rcv+0x744/0x1150 [tipc] This patch fixes it by re-fetching the skb cb from the new allocated skb after calling tipc_msg_validate().

In the Linux kernel, the following vulnerability has been resolved: net: hsr: Fix potential use-after-free The skb is delivered to netif_rx() which may free it, after calling this, dereferencing skb may trigger use-after-free.

In the Linux kernel, the following vulnerability has been resolved: nvme: fix SRCU protection of nvme_ns_head list Walking the nvme_ns_head siblings list is protected by the head's srcu in nvme_ns_head_submit_bio() but not nvme_mpath_revalidate_paths(). Removing namespaces from the list also fails to synchronize the srcu. Concurrent scan work can therefore cause use-after-frees. Hold the head's srcu lock in nvme_mpath_revalidate_paths() and synchronize with the srcu, not the global RCU, in nvme_ns_remove(). Observed the following panic when making NVMe/RDMA connections with native multipath on the Rocky Linux 8.6 kernel (it seems the upstream kernel has the same race condition). Disassembly shows the faulting instruction is cmp 0x50(%rdx),%rcx; computing capacity != get_capacity(ns->disk). Address 0x50 is dereferenced because ns->disk is NULL. The NULL disk appears to be the result of concurrent scan work freeing the namespace (note the log line in the middle of the panic). [37314.206036] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050 [37314.206036] nvme0n3: detected capacity change from 0 to 11811160064 [37314.299753] PGD 0 P4D 0 [37314.299756] Oops: 0000 [#1] SMP PTI [37314.299759] CPU: 29 PID: 322046 Comm: kworker/u98:3 Kdump: loaded Tainted: G W X --------- - - 4.18.0-372.32.1.el8test86.x86_64 #1 [37314.299762] Hardware name: Dell Inc. PowerEdge R720/0JP31P, BIOS 2.7.0 05/23/2018 [37314.299763] Workqueue: nvme-wq nvme_scan_work [nvme_core] [37314.299783] RIP: 0010:nvme_mpath_revalidate_paths+0x26/0xb0 [nvme_core] [37314.299790] Code: 1f 44 00 00 66 66 66 66 90 55 53 48 8b 5f 50 48 8b 83 c8 c9 00 00 48 8b 13 48 8b 48 50 48 39 d3 74 20 48 8d 42 d0 48 8b 50 20 <48> 3b 4a 50 74 05 f0 80 60 70 ef 48 8b 50 30 48 8d 42 d0 48 39 d3 [37315.058803] RSP: 0018:ffffabe28f913d10 EFLAGS: 00010202 [37315.121316] RAX: ffff927a077da800 RBX: ffff92991dd70000 RCX: 0000000001600000 [37315.206704] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff92991b719800 [37315.292106] RBP: ffff929a6b70c000 R08: 000000010234cd4a R09: c0000000ffff7fff [37315.377501] R10: 0000000000000001 R11: ffffabe28f913a30 R12: 0000000000000000 [37315.462889] R13: ffff92992716600c R14: ffff929964e6e030 R15: ffff92991dd70000 [37315.548286] FS: 0000000000000000(0000) GS:ffff92b87fb80000(0000) knlGS:0000000000000000 [37315.645111] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [37315.713871] CR2: 0000000000000050 CR3: 0000002208810006 CR4: 00000000000606e0 [37315.799267] Call Trace: [37315.828515] nvme_update_ns_info+0x1ac/0x250 [nvme_core] [37315.892075] nvme_validate_or_alloc_ns+0x2ff/0xa00 [nvme_core] [37315.961871] ? __blk_mq_free_request+0x6b/0x90 [37316.015021] nvme_scan_work+0x151/0x240 [nvme_core] [37316.073371] process_one_work+0x1a7/0x360 [37316.121318] ? create_worker+0x1a0/0x1a0 [37316.168227] worker_thread+0x30/0x390 [37316.212024] ? create_worker+0x1a0/0x1a0 [37316.258939] kthread+0x10a/0x120 [37316.297557] ? set_kthread_struct+0x50/0x50 [37316.347590] ret_from_fork+0x35/0x40 [37316.390360] Modules linked in: nvme_rdma nvme_tcp(X) nvme_fabrics nvme_core netconsole iscsi_tcp libiscsi_tcp dm_queue_length dm_service_time nf_conntrack_netlink br_netfilter bridge stp llc overlay nft_chain_nat ipt_MASQUERADE nf_nat xt_addrtype xt_CT nft_counter xt_state xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xt_comment xt_multiport nft_compat nf_tables libcrc32c nfnetlink dm_multipath tg3 rpcrdma sunrpc rdma_ucm ib_srpt ib_isert iscsi_target_mod target_core_mod ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm intel_rapl_msr iTCO_wdt iTCO_vendor_support dcdbas intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel ipmi_ssif kvm irqbypass crct10dif_pclmul crc32_pclmul mlx5_ib ghash_clmulni_intel ib_uverbs rapl intel_cstate intel_uncore ib_core ipmi_si joydev mei_me pcspkr ipmi_devintf mei lpc_ich wmi ipmi_msghandler acpi_power_meter ex ---truncated---

In the Linux kernel, the following vulnerability has been resolved: memcg: fix possible use-after-free in memcg_write_event_control() memcg_write_event_control() accesses the dentry->d_name of the specified control fd to route the write call. As a cgroup interface file can't be renamed, it's safe to access d_name as long as the specified file is a regular cgroup file. Also, as these cgroup interface files can't be removed before the directory, it's safe to access the parent too. Prior to 347c4a874710 ("memcg: remove cgroup_event->cft"), there was a call to __file_cft() which verified that the specified file is a regular cgroupfs file before further accesses. The cftype pointer returned from __file_cft() was no longer necessary and the commit inadvertently dropped the file type check with it allowing any file to slip through. With the invarients broken, the d_name and parent accesses can now race against renames and removals of arbitrary files and cause use-after-free's. Fix the bug by resurrecting the file type check in __file_cft(). Now that cgroupfs is implemented through kernfs, checking the file operations needs to go through a layer of indirection. Instead, let's check the superblock and dentry type.

In the Linux kernel, the following vulnerability has been resolved: mm/gup: fix gup_pud_range() for dax For dax pud, pud_huge() returns true on x86. So the function works as long as hugetlb is configured. However, dax doesn't depend on hugetlb. Commit 414fd080d125 ("mm/gup: fix gup_pmd_range() for dax") fixed devmap-backed huge PMDs, but missed devmap-backed huge PUDs. Fix this as well. This fixes the below kernel panic: general protection fault, probably for non-canonical address 0x69e7c000cc478: 0000 [#1] SMP < snip > Call Trace: <TASK> get_user_pages_fast+0x1f/0x40 iov_iter_get_pages+0xc6/0x3b0 ? mempool_alloc+0x5d/0x170 bio_iov_iter_get_pages+0x82/0x4e0 ? bvec_alloc+0x91/0xc0 ? bio_alloc_bioset+0x19a/0x2a0 blkdev_direct_IO+0x282/0x480 ? __io_complete_rw_common+0xc0/0xc0 ? filemap_range_has_page+0x82/0xc0 generic_file_direct_write+0x9d/0x1a0 ? inode_update_time+0x24/0x30 __generic_file_write_iter+0xbd/0x1e0 blkdev_write_iter+0xb4/0x150 ? io_import_iovec+0x8d/0x340 io_write+0xf9/0x300 io_issue_sqe+0x3c3/0x1d30 ? sysvec_reschedule_ipi+0x6c/0x80 __io_queue_sqe+0x33/0x240 ? fget+0x76/0xa0 io_submit_sqes+0xe6a/0x18d0 ? __fget_light+0xd1/0x100 __x64_sys_io_uring_enter+0x199/0x880 ? __context_tracking_enter+0x1f/0x70 ? irqentry_exit_to_user_mode+0x24/0x30 ? irqentry_exit+0x1d/0x30 ? __context_tracking_exit+0xe/0x70 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x61/0xcb RIP: 0033:0x7fc97c11a7be < snip > </TASK> ---[ end trace 48b2e0e67debcaeb ]--- RIP: 0010:internal_get_user_pages_fast+0x340/0x990 < snip > Kernel panic - not syncing: Fatal exception Kernel Offset: disabled

In the Linux kernel, the following vulnerability has been resolved: net: mana: Fix race on per-CQ variable napi work_done After calling napi_complete_done(), the NAPIF_STATE_SCHED bit may be cleared, and another CPU can start napi thread and access per-CQ variable, cq->work_done. If the other thread (for example, from busy_poll) sets it to a value >= budget, this thread will continue to run when it should stop, and cause memory corruption and panic. To fix this issue, save the per-CQ work_done variable in a local variable before napi_complete_done(), so it won't be corrupted by a possible concurrent thread after napi_complete_done(). Also, add a flag bit to advertise to the NIC firmware: the NAPI work_done variable race is fixed, so the driver is able to reliably support features like busy_poll.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix array index out of bound error in DCN32 DML [Why&How] LinkCapacitySupport array is indexed with the number of voltage states and not the number of max DPPs. Fix the error by changing the array declaration to use the correct (larger) array size of total number of voltage states.

In the Linux kernel, the following vulnerability has been resolved: NFC: nci: Bounds check struct nfc_target arrays While running under CONFIG_FORTIFY_SOURCE=y, syzkaller reported: memcpy: detected field-spanning write (size 129) of single field "target->sensf_res" at net/nfc/nci/ntf.c:260 (size 18) This appears to be a legitimate lack of bounds checking in nci_add_new_protocol(). Add the missing checks.

In the Linux kernel, the following vulnerability has been resolved: ravb: Fix potential use-after-free in ravb_rx_gbeth() The skb is delivered to napi_gro_receive() which may free it, after calling this, dereferencing skb may trigger use-after-free.

In the Linux kernel, the following vulnerability has been resolved: net: hisilicon: Fix potential use-after-free in hix5hd2_rx() The skb is delivered to napi_gro_receive() which may free it, after calling this, dereferencing skb may trigger use-after-free.

In the Linux kernel, the following vulnerability has been resolved: s390/qeth: fix use-after-free in hsci KASAN found that addr was dereferenced after br2dev_event_work was freed. ================================================================== BUG: KASAN: use-after-free in qeth_l2_br2dev_worker+0x5ba/0x6b0 Read of size 1 at addr 00000000fdcea440 by task kworker/u760:4/540 CPU: 17 PID: 540 Comm: kworker/u760:4 Tainted: G E 6.1.0-20221128.rc7.git1.5aa3bed4ce83.300.fc36.s390x+kasan #1 Hardware name: IBM 8561 T01 703 (LPAR) Workqueue: 0.0.8000_event qeth_l2_br2dev_worker Call Trace: [<000000016944d4ce>] dump_stack_lvl+0xc6/0xf8 [<000000016942cd9c>] print_address_description.constprop.0+0x34/0x2a0 [<000000016942d118>] print_report+0x110/0x1f8 [<0000000167a7bd04>] kasan_report+0xfc/0x128 [<000000016938d79a>] qeth_l2_br2dev_worker+0x5ba/0x6b0 [<00000001673edd1e>] process_one_work+0x76e/0x1128 [<00000001673ee85c>] worker_thread+0x184/0x1098 [<000000016740718a>] kthread+0x26a/0x310 [<00000001672c606a>] __ret_from_fork+0x8a/0xe8 [<00000001694711da>] ret_from_fork+0xa/0x40 Allocated by task 108338: kasan_save_stack+0x40/0x68 kasan_set_track+0x36/0x48 __kasan_kmalloc+0xa0/0xc0 qeth_l2_switchdev_event+0x25a/0x738 atomic_notifier_call_chain+0x9c/0xf8 br_switchdev_fdb_notify+0xf4/0x110 fdb_notify+0x122/0x180 fdb_add_entry.constprop.0.isra.0+0x312/0x558 br_fdb_add+0x59e/0x858 rtnl_fdb_add+0x58a/0x928 rtnetlink_rcv_msg+0x5f8/0x8d8 netlink_rcv_skb+0x1f2/0x408 netlink_unicast+0x570/0x790 netlink_sendmsg+0x752/0xbe0 sock_sendmsg+0xca/0x110 ____sys_sendmsg+0x510/0x6a8 ___sys_sendmsg+0x12a/0x180 __sys_sendmsg+0xe6/0x168 __do_sys_socketcall+0x3c8/0x468 do_syscall+0x22c/0x328 __do_syscall+0x94/0xf0 system_call+0x82/0xb0 Freed by task 540: kasan_save_stack+0x40/0x68 kasan_set_track+0x36/0x48 kasan_save_free_info+0x4c/0x68 ____kasan_slab_free+0x14e/0x1a8 __kasan_slab_free+0x24/0x30 __kmem_cache_free+0x168/0x338 qeth_l2_br2dev_worker+0x154/0x6b0 process_one_work+0x76e/0x1128 worker_thread+0x184/0x1098 kthread+0x26a/0x310 __ret_from_fork+0x8a/0xe8 ret_from_fork+0xa/0x40 Last potentially related work creation: kasan_save_stack+0x40/0x68 __kasan_record_aux_stack+0xbe/0xd0 insert_work+0x56/0x2e8 __queue_work+0x4ce/0xd10 queue_work_on+0xf4/0x100 qeth_l2_switchdev_event+0x520/0x738 atomic_notifier_call_chain+0x9c/0xf8 br_switchdev_fdb_notify+0xf4/0x110 fdb_notify+0x122/0x180 fdb_add_entry.constprop.0.isra.0+0x312/0x558 br_fdb_add+0x59e/0x858 rtnl_fdb_add+0x58a/0x928 rtnetlink_rcv_msg+0x5f8/0x8d8 netlink_rcv_skb+0x1f2/0x408 netlink_unicast+0x570/0x790 netlink_sendmsg+0x752/0xbe0 sock_sendmsg+0xca/0x110 ____sys_sendmsg+0x510/0x6a8 ___sys_sendmsg+0x12a/0x180 __sys_sendmsg+0xe6/0x168 __do_sys_socketcall+0x3c8/0x468 do_syscall+0x22c/0x328 __do_syscall+0x94/0xf0 system_call+0x82/0xb0 Second to last potentially related work creation: kasan_save_stack+0x40/0x68 __kasan_record_aux_stack+0xbe/0xd0 kvfree_call_rcu+0xb2/0x760 kernfs_unlink_open_file+0x348/0x430 kernfs_fop_release+0xc2/0x320 __fput+0x1ae/0x768 task_work_run+0x1bc/0x298 exit_to_user_mode_prepare+0x1a0/0x1a8 __do_syscall+0x94/0xf0 system_call+0x82/0xb0 The buggy address belongs to the object at 00000000fdcea400 which belongs to the cache kmalloc-96 of size 96 The buggy address is located 64 bytes inside of 96-byte region [00000000fdcea400, 00000000fdcea460) The buggy address belongs to the physical page: page:000000005a9c26e8 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0xfdcea flags: 0x3ffff00000000200(slab|node=0|zone=1|lastcpupid=0x1ffff) raw: 3ffff00000000200 0000000000000000 0000000100000122 000000008008cc00 raw: 0000000000000000 0020004100000000 ffffffff00000001 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: 00000000fdcea300: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc 00000000fdcea380: fb fb fb fb fb fb f ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ALSA: asihpi: Fix potential OOB array access ASIHPI driver stores some values in the static array upon a response from the driver, and its index depends on the firmware. We shouldn't trust it blindly. This patch adds a sanity check of the array index to fit in the array size.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: amdkfd_free_gtt_mem clear the correct pointer Pass pointer reference to amdgpu_bo_unref to clear the correct pointer, otherwise amdgpu_bo_unref clear the local variable, the original pointer not set to NULL, this could cause use-after-free bug.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix double free issue during amdgpu module unload Flexible endpoints use DIGs from available inflexible endpoints, so only the encoders of inflexible links need to be freed. Otherwise, a double free issue may occur when unloading the amdgpu module. [ 279.190523] RIP: 0010:__slab_free+0x152/0x2f0 [ 279.190577] Call Trace: [ 279.190580] <TASK> [ 279.190582] ? show_regs+0x69/0x80 [ 279.190590] ? die+0x3b/0x90 [ 279.190595] ? do_trap+0xc8/0xe0 [ 279.190601] ? do_error_trap+0x73/0xa0 [ 279.190605] ? __slab_free+0x152/0x2f0 [ 279.190609] ? exc_invalid_op+0x56/0x70 [ 279.190616] ? __slab_free+0x152/0x2f0 [ 279.190642] ? asm_exc_invalid_op+0x1f/0x30 [ 279.190648] ? dcn10_link_encoder_destroy+0x19/0x30 [amdgpu] [ 279.191096] ? __slab_free+0x152/0x2f0 [ 279.191102] ? dcn10_link_encoder_destroy+0x19/0x30 [amdgpu] [ 279.191469] kfree+0x260/0x2b0 [ 279.191474] dcn10_link_encoder_destroy+0x19/0x30 [amdgpu] [ 279.191821] link_destroy+0xd7/0x130 [amdgpu] [ 279.192248] dc_destruct+0x90/0x270 [amdgpu] [ 279.192666] dc_destroy+0x19/0x40 [amdgpu] [ 279.193020] amdgpu_dm_fini+0x16e/0x200 [amdgpu] [ 279.193432] dm_hw_fini+0x26/0x40 [amdgpu] [ 279.193795] amdgpu_device_fini_hw+0x24c/0x400 [amdgpu] [ 279.194108] amdgpu_driver_unload_kms+0x4f/0x70 [amdgpu] [ 279.194436] amdgpu_pci_remove+0x40/0x80 [amdgpu] [ 279.194632] pci_device_remove+0x3a/0xa0 [ 279.194638] device_remove+0x40/0x70 [ 279.194642] device_release_driver_internal+0x1ad/0x210 [ 279.194647] driver_detach+0x4e/0xa0 [ 279.194650] bus_remove_driver+0x6f/0xf0 [ 279.194653] driver_unregister+0x33/0x60 [ 279.194657] pci_unregister_driver+0x44/0x90 [ 279.194662] amdgpu_exit+0x19/0x1f0 [amdgpu] [ 279.194939] __do_sys_delete_module.isra.0+0x198/0x2f0 [ 279.194946] __x64_sys_delete_module+0x16/0x20 [ 279.194950] do_syscall_64+0x58/0x120 [ 279.194954] entry_SYSCALL_64_after_hwframe+0x6e/0x76 [ 279.194980] </TASK>

In the Linux kernel, the following vulnerability has been resolved: platform/x86: x86-android-tablets: Fix use after free on platform_device_register() errors x86_android_tablet_remove() frees the pdevs[] array, so it should not be used after calling x86_android_tablet_remove(). When platform_device_register() fails, store the pdevs[x] PTR_ERR() value into the local ret variable before calling x86_android_tablet_remove() to avoid using pdevs[] after it has been freed.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: cancel dqi_sync_work before freeing oinfo ocfs2_global_read_info() will initialize and schedule dqi_sync_work at the end, if error occurs after successfully reading global quota, it will trigger the following warning with CONFIG_DEBUG_OBJECTS_* enabled: ODEBUG: free active (active state 0) object: 00000000d8b0ce28 object type: timer_list hint: qsync_work_fn+0x0/0x16c This reports that there is an active delayed work when freeing oinfo in error handling, so cancel dqi_sync_work first. BTW, return status instead of -1 when .read_file_info fails.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: Avoid a bad reference count on CPU node In the parse_perf_domain function, if the call to of_parse_phandle_with_args returns an error, then the reference to the CPU device node that was acquired at the start of the function would not be properly decremented. Address this by declaring the variable with the __free(device_node) cleanup attribute.

A Buffer Overflow vulnerability in the local_app_set_router_wan function of Vilo 5 Mesh WiFi System <= 5.16.1.33 allows remote, unauthenticated attackers to execute arbitrary code via pppoe_username and pppoe_password fields being larger than 128 bytes in length.

Buffer Overflow vulnerability in IrfanView 32bit v.4.66 allows a local attacker to cause a denial of service via a crafted file. Affected component is IrfanView 32bit 4.66 with plugin formats.dll.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: improve shutdown sequence Alexander Sverdlin presents 2 problems during shutdown with the lan9303 driver. One is specific to lan9303 and the other just happens to reproduce there. The first problem is that lan9303 is unique among DSA drivers in that it calls dev_get_drvdata() at "arbitrary runtime" (not probe, not shutdown, not remove): phy_state_machine() -> ... -> dsa_user_phy_read() -> ds->ops->phy_read() -> lan9303_phy_read() -> chip->ops->phy_read() -> lan9303_mdio_phy_read() -> dev_get_drvdata() But we never stop the phy_state_machine(), so it may continue to run after dsa_switch_shutdown(). Our common pattern in all DSA drivers is to set drvdata to NULL to suppress the remove() method that may come afterwards. But in this case it will result in an NPD. The second problem is that the way in which we set dp->conduit->dsa_ptr = NULL; is concurrent with receive packet processing. dsa_switch_rcv() checks once whether dev->dsa_ptr is NULL, but afterwards, rather than continuing to use that non-NULL value, dev->dsa_ptr is dereferenced again and again without NULL checks: dsa_conduit_find_user() and many other places. In between dereferences, there is no locking to ensure that what was valid once continues to be valid. Both problems have the common aspect that closing the conduit interface solves them. In the first case, dev_close(conduit) triggers the NETDEV_GOING_DOWN event in dsa_user_netdevice_event() which closes user ports as well. dsa_port_disable_rt() calls phylink_stop(), which synchronously stops the phylink state machine, and ds->ops->phy_read() will thus no longer call into the driver after this point. In the second case, dev_close(conduit) should do this, as per Documentation/networking/driver.rst: | Quiescence | ---------- | | After the ndo_stop routine has been called, the hardware must | not receive or transmit any data. All in flight packets must | be aborted. If necessary, poll or wait for completion of | any reset commands. So it should be sufficient to ensure that later, when we zeroize conduit->dsa_ptr, there will be no concurrent dsa_switch_rcv() call on this conduit. The addition of the netif_device_detach() function is to ensure that ioctls, rtnetlinks and ethtool requests on the user ports no longer propagate down to the driver - we're no longer prepared to handle them. The race condition actually did not exist when commit 0650bf52b31f ("net: dsa: be compatible with masters which unregister on shutdown") first introduced dsa_switch_shutdown(). It was created later, when we stopped unregistering the user interfaces from a bad spot, and we just replaced that sequence with a racy zeroization of conduit->dsa_ptr (one which doesn't ensure that the interfaces aren't up).

In the Linux kernel, the following vulnerability has been resolved: gpiolib: Fix potential NULL pointer dereference in gpiod_get_label() In `gpiod_get_label()`, it is possible that `srcu_dereference_check()` may return a NULL pointer, leading to a scenario where `label->str` is accessed without verifying if `label` itself is NULL. This patch adds a proper NULL check for `label` before accessing `label->str`. The check for `label->str != NULL` is removed because `label->str` can never be NULL if `label` is not NULL. This fixes the issue where the label name was being printed as `(efault)` when dumping the sysfs GPIO file when `label == NULL`.

In the Linux kernel, the following vulnerability has been resolved: ext4: aovid use-after-free in ext4_ext_insert_extent() As Ojaswin mentioned in Link, in ext4_ext_insert_extent(), if the path is reallocated in ext4_ext_create_new_leaf(), we'll use the stale path and cause UAF. Below is a sample trace with dummy values: ext4_ext_insert_extent path = *ppath = 2000 ext4_ext_create_new_leaf(ppath) ext4_find_extent(ppath) path = *ppath = 2000 if (depth > path[0].p_maxdepth) kfree(path = 2000); *ppath = path = NULL; path = kcalloc() = 3000 *ppath = 3000; return path; /* here path is still 2000, UAF! */ eh = path[depth].p_hdr ================================================================== BUG: KASAN: slab-use-after-free in ext4_ext_insert_extent+0x26d4/0x3330 Read of size 8 at addr ffff8881027bf7d0 by task kworker/u36:1/179 CPU: 3 UID: 0 PID: 179 Comm: kworker/u6:1 Not tainted 6.11.0-rc2-dirty #866 Call Trace: <TASK> ext4_ext_insert_extent+0x26d4/0x3330 ext4_ext_map_blocks+0xe22/0x2d40 ext4_map_blocks+0x71e/0x1700 ext4_do_writepages+0x1290/0x2800 [...] Allocated by task 179: ext4_find_extent+0x81c/0x1f70 ext4_ext_map_blocks+0x146/0x2d40 ext4_map_blocks+0x71e/0x1700 ext4_do_writepages+0x1290/0x2800 ext4_writepages+0x26d/0x4e0 do_writepages+0x175/0x700 [...] Freed by task 179: kfree+0xcb/0x240 ext4_find_extent+0x7c0/0x1f70 ext4_ext_insert_extent+0xa26/0x3330 ext4_ext_map_blocks+0xe22/0x2d40 ext4_map_blocks+0x71e/0x1700 ext4_do_writepages+0x1290/0x2800 ext4_writepages+0x26d/0x4e0 do_writepages+0x175/0x700 [...] ================================================================== So use *ppath to update the path to avoid the above problem.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix double brelse() the buffer of the extents path In ext4_ext_try_to_merge_up(), set path[1].p_bh to NULL after it has been released, otherwise it may be released twice. An example of what triggers this is as follows: split2 map split1 |--------|-------|--------| ext4_ext_map_blocks ext4_ext_handle_unwritten_extents ext4_split_convert_extents // path->p_depth == 0 ext4_split_extent // 1. do split1 ext4_split_extent_at |ext4_ext_insert_extent | ext4_ext_create_new_leaf | ext4_ext_grow_indepth | le16_add_cpu(&neh->eh_depth, 1) | ext4_find_extent | // return -ENOMEM |// get error and try zeroout |path = ext4_find_extent | path->p_depth = 1 |ext4_ext_try_to_merge | ext4_ext_try_to_merge_up | path->p_depth = 0 | brelse(path[1].p_bh) ---> not set to NULL here |// zeroout success // 2. update path ext4_find_extent // 3. do split2 ext4_split_extent_at ext4_ext_insert_extent ext4_ext_create_new_leaf ext4_ext_grow_indepth le16_add_cpu(&neh->eh_depth, 1) ext4_find_extent path[0].p_bh = NULL; path->p_depth = 1 read_extent_tree_block ---> return err // path[1].p_bh is still the old value ext4_free_ext_path ext4_ext_drop_refs // path->p_depth == 1 brelse(path[1].p_bh) ---> brelse a buffer twice Finally got the following WARRNING when removing the buffer from lru: ============================================ VFS: brelse: Trying to free free buffer WARNING: CPU: 2 PID: 72 at fs/buffer.c:1241 __brelse+0x58/0x90 CPU: 2 PID: 72 Comm: kworker/u19:1 Not tainted 6.9.0-dirty #716 RIP: 0010:__brelse+0x58/0x90 Call Trace: <TASK> __find_get_block+0x6e7/0x810 bdev_getblk+0x2b/0x480 __ext4_get_inode_loc+0x48a/0x1240 ext4_get_inode_loc+0xb2/0x150 ext4_reserve_inode_write+0xb7/0x230 __ext4_mark_inode_dirty+0x144/0x6a0 ext4_ext_insert_extent+0x9c8/0x3230 ext4_ext_map_blocks+0xf45/0x2dc0 ext4_map_blocks+0x724/0x1700 ext4_do_writepages+0x12d6/0x2a70 [...] ============================================

In the Linux kernel, the following vulnerability has been resolved: firmware_loader: Block path traversal Most firmware names are hardcoded strings, or are constructed from fairly constrained format strings where the dynamic parts are just some hex numbers or such. However, there are a couple codepaths in the kernel where firmware file names contain string components that are passed through from a device or semi-privileged userspace; the ones I could find (not counting interfaces that require root privileges) are: - lpfc_sli4_request_firmware_update() seems to construct the firmware filename from "ModelName", a string that was previously parsed out of some descriptor ("Vital Product Data") in lpfc_fill_vpd() - nfp_net_fw_find() seems to construct a firmware filename from a model name coming from nfp_hwinfo_lookup(pf->hwinfo, "nffw.partno"), which I think parses some descriptor that was read from the device. (But this case likely isn't exploitable because the format string looks like "netronome/nic_%s", and there shouldn't be any *folders* starting with "netronome/nic_". The previous case was different because there, the "%s" is *at the start* of the format string.) - module_flash_fw_schedule() is reachable from the ETHTOOL_MSG_MODULE_FW_FLASH_ACT netlink command, which is marked as GENL_UNS_ADMIN_PERM (meaning CAP_NET_ADMIN inside a user namespace is enough to pass the privilege check), and takes a userspace-provided firmware name. (But I think to reach this case, you need to have CAP_NET_ADMIN over a network namespace that a special kind of ethernet device is mapped into, so I think this is not a viable attack path in practice.) Fix it by rejecting any firmware names containing ".." path components. For what it's worth, I went looking and haven't found any USB device drivers that use the firmware loader dangerously.

In the Linux kernel, the following vulnerability has been resolved: serial: protect uart_port_dtr_rts() in uart_shutdown() too Commit af224ca2df29 (serial: core: Prevent unsafe uart port access, part 3) added few uport == NULL checks. It added one to uart_shutdown(), so the commit assumes, uport can be NULL in there. But right after that protection, there is an unprotected "uart_port_dtr_rts(uport, false);" call. That is invoked only if HUPCL is set, so I assume that is the reason why we do not see lots of these reports. Or it cannot be NULL at this point at all for some reason :P. Until the above is investigated, stay on the safe side and move this dereference to the if too. I got this inconsistency from Coverity under CID 1585130. Thanks.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: FIX possible deadlock in rfcomm_sk_state_change rfcomm_sk_state_change attempts to use sock_lock so it must never be called with it locked but rfcomm_sock_ioctl always attempt to lock it causing the following trace: ====================================================== WARNING: possible circular locking dependency detected 6.8.0-syzkaller-08951-gfe46a7dd189e #0 Not tainted ------------------------------------------------------ syz-executor386/5093 is trying to acquire lock: ffff88807c396258 (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1671 [inline] ffff88807c396258 (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+.}-{0:0}, at: rfcomm_sk_state_change+0x5b/0x310 net/bluetooth/rfcomm/sock.c:73 but task is already holding lock: ffff88807badfd28 (&d->lock){+.+.}-{3:3}, at: __rfcomm_dlc_close+0x226/0x6a0 net/bluetooth/rfcomm/core.c:491

In the Linux kernel, the following vulnerability has been resolved: igb: Do not bring the device up after non-fatal error Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal") changed igb_io_error_detected() to ignore non-fatal pcie errors in order to avoid hung task that can happen when igb_down() is called multiple times. This caused an issue when processing transient non-fatal errors. igb_io_resume(), which is called after igb_io_error_detected(), assumes that device is brought down by igb_io_error_detected() if the interface is up. This resulted in panic with stacktrace below. [ T3256] igb 0000:09:00.0 haeth0: igb: haeth0 NIC Link is Down [ T292] pcieport 0000:00:1c.5: AER: Uncorrected (Non-Fatal) error received: 0000:09:00.0 [ T292] igb 0000:09:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID) [ T292] igb 0000:09:00.0: device [8086:1537] error status/mask=00004000/00000000 [ T292] igb 0000:09:00.0: [14] CmpltTO [ 200.105524,009][ T292] igb 0000:09:00.0: AER: TLP Header: 00000000 00000000 00000000 00000000 [ T292] pcieport 0000:00:1c.5: AER: broadcast error_detected message [ T292] igb 0000:09:00.0: Non-correctable non-fatal error reported. [ T292] pcieport 0000:00:1c.5: AER: broadcast mmio_enabled message [ T292] pcieport 0000:00:1c.5: AER: broadcast resume message [ T292] ------------[ cut here ]------------ [ T292] kernel BUG at net/core/dev.c:6539! [ T292] invalid opcode: 0000 [#1] PREEMPT SMP [ T292] RIP: 0010:napi_enable+0x37/0x40 [ T292] Call Trace: [ T292] <TASK> [ T292] ? die+0x33/0x90 [ T292] ? do_trap+0xdc/0x110 [ T292] ? napi_enable+0x37/0x40 [ T292] ? do_error_trap+0x70/0xb0 [ T292] ? napi_enable+0x37/0x40 [ T292] ? napi_enable+0x37/0x40 [ T292] ? exc_invalid_op+0x4e/0x70 [ T292] ? napi_enable+0x37/0x40 [ T292] ? asm_exc_invalid_op+0x16/0x20 [ T292] ? napi_enable+0x37/0x40 [ T292] igb_up+0x41/0x150 [ T292] igb_io_resume+0x25/0x70 [ T292] report_resume+0x54/0x70 [ T292] ? report_frozen_detected+0x20/0x20 [ T292] pci_walk_bus+0x6c/0x90 [ T292] ? aer_print_port_info+0xa0/0xa0 [ T292] pcie_do_recovery+0x22f/0x380 [ T292] aer_process_err_devices+0x110/0x160 [ T292] aer_isr+0x1c1/0x1e0 [ T292] ? disable_irq_nosync+0x10/0x10 [ T292] irq_thread_fn+0x1a/0x60 [ T292] irq_thread+0xe3/0x1a0 [ T292] ? irq_set_affinity_notifier+0x120/0x120 [ T292] ? irq_affinity_notify+0x100/0x100 [ T292] kthread+0xe2/0x110 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork+0x2d/0x50 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork_asm+0x11/0x20 [ T292] </TASK> To fix this issue igb_io_resume() checks if the interface is running and the device is not down this means igb_io_error_detected() did not bring the device down and there is no need to bring it up.

In the Linux kernel, the following vulnerability has been resolved: exec: don't WARN for racy path_noexec check Both i_mode and noexec checks wrapped in WARN_ON stem from an artifact of the previous implementation. They used to legitimately check for the condition, but that got moved up in two commits: 633fb6ac3980 ("exec: move S_ISREG() check earlier") 0fd338b2d2cd ("exec: move path_noexec() check earlier") Instead of being removed said checks are WARN_ON'ed instead, which has some debug value. However, the spurious path_noexec check is racy, resulting in unwarranted warnings should someone race with setting the noexec flag. One can note there is more to perm-checking whether execve is allowed and none of the conditions are guaranteed to still hold after they were tested for. Additionally this does not validate whether the code path did any perm checking to begin with -- it will pass if the inode happens to be regular. Keep the redundant path_noexec() check even though it's mindless nonsense checking for guarantee that isn't given so drop the WARN. Reword the commentary and do small tidy ups while here. [brauner: keep redundant path_noexec() check]

In the Linux kernel, the following vulnerability has been resolved: ext4: fix i_data_sem unlock order in ext4_ind_migrate() Fuzzing reports a possible deadlock in jbd2_log_wait_commit. This issue is triggered when an EXT4_IOC_MIGRATE ioctl is set to require synchronous updates because the file descriptor is opened with O_SYNC. This can lead to the jbd2_journal_stop() function calling jbd2_might_wait_for_commit(), potentially causing a deadlock if the EXT4_IOC_MIGRATE call races with a write(2) system call. This problem only arises when CONFIG_PROVE_LOCKING is enabled. In this case, the jbd2_might_wait_for_commit macro locks jbd2_handle in the jbd2_journal_stop function while i_data_sem is locked. This triggers lockdep because the jbd2_journal_start function might also lock the same jbd2_handle simultaneously. Found by Linux Verification Center (linuxtesting.org) with syzkaller. Rule: add

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: Fix zero-division error when disabling tc cbs The commit b8c43360f6e4 ("net: stmmac: No need to calculate speed divider when offload is disabled") allows the "port_transmit_rate_kbps" to be set to a value of 0, which is then passed to the "div_s64" function when tc-cbs is disabled. This leads to a zero-division error. When tc-cbs is disabled, the idleslope, sendslope, and credit values the credit values are not required to be configured. Therefore, adding a return statement after setting the txQ mode to DCB when tc-cbs is disabled would prevent a zero-division error.

In the Linux kernel, the following vulnerability has been resolved: ACPI: battery: Fix possible crash when unregistering a battery hook When a battery hook returns an error when adding a new battery, then the battery hook is automatically unregistered. However the battery hook provider cannot know that, so it will later call battery_hook_unregister() on the already unregistered battery hook, resulting in a crash. Fix this by using the list head to mark already unregistered battery hooks as already being unregistered so that they can be ignored by battery_hook_unregister().

In the Linux kernel, the following vulnerability has been resolved: net: avoid potential underflow in qdisc_pkt_len_init() with UFO After commit 7c6d2ecbda83 ("net: be more gentle about silly gso requests coming from user") virtio_net_hdr_to_skb() had sanity check to detect malicious attempts from user space to cook a bad GSO packet. Then commit cf9acc90c80ec ("net: virtio_net_hdr_to_skb: count transport header in UFO") while fixing one issue, allowed user space to cook a GSO packet with the following characteristic : IPv4 SKB_GSO_UDP, gso_size=3, skb->len = 28. When this packet arrives in qdisc_pkt_len_init(), we end up with hdr_len = 28 (IPv4 header + UDP header), matching skb->len Then the following sets gso_segs to 0 : gso_segs = DIV_ROUND_UP(skb->len - hdr_len, shinfo->gso_size); Then later we set qdisc_skb_cb(skb)->pkt_len to back to zero :/ qdisc_skb_cb(skb)->pkt_len += (gso_segs - 1) * hdr_len; This leads to the following crash in fq_codel [1] qdisc_pkt_len_init() is best effort, we only want an estimation of the bytes sent on the wire, not crashing the kernel. This patch is fixing this particular issue, a following one adds more sanity checks for another potential bug. [1] [ 70.724101] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 70.724561] #PF: supervisor read access in kernel mode [ 70.724561] #PF: error_code(0x0000) - not-present page [ 70.724561] PGD 10ac61067 P4D 10ac61067 PUD 107ee2067 PMD 0 [ 70.724561] Oops: Oops: 0000 [#1] SMP NOPTI [ 70.724561] CPU: 11 UID: 0 PID: 2163 Comm: b358537762 Not tainted 6.11.0-virtme #991 [ 70.724561] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 70.724561] RIP: 0010:fq_codel_enqueue (net/sched/sch_fq_codel.c:120 net/sched/sch_fq_codel.c:168 net/sched/sch_fq_codel.c:230) sch_fq_codel [ 70.724561] Code: 24 08 49 c1 e1 06 44 89 7c 24 18 45 31 ed 45 31 c0 31 ff 89 44 24 14 4c 03 8b 90 01 00 00 eb 04 39 ca 73 37 4d 8b 39 83 c7 01 <49> 8b 17 49 89 11 41 8b 57 28 45 8b 5f 34 49 c7 07 00 00 00 00 49 All code ======== 0: 24 08 and $0x8,%al 2: 49 c1 e1 06 shl $0x6,%r9 6: 44 89 7c 24 18 mov %r15d,0x18(%rsp) b: 45 31 ed xor %r13d,%r13d e: 45 31 c0 xor %r8d,%r8d 11: 31 ff xor %edi,%edi 13: 89 44 24 14 mov %eax,0x14(%rsp) 17: 4c 03 8b 90 01 00 00 add 0x190(%rbx),%r9 1e: eb 04 jmp 0x24 20: 39 ca cmp %ecx,%edx 22: 73 37 jae 0x5b 24: 4d 8b 39 mov (%r9),%r15 27: 83 c7 01 add $0x1,%edi 2a:* 49 8b 17 mov (%r15),%rdx <-- trapping instruction 2d: 49 89 11 mov %rdx,(%r9) 30: 41 8b 57 28 mov 0x28(%r15),%edx 34: 45 8b 5f 34 mov 0x34(%r15),%r11d 38: 49 c7 07 00 00 00 00 movq $0x0,(%r15) 3f: 49 rex.WB Code starting with the faulting instruction =========================================== 0: 49 8b 17 mov (%r15),%rdx 3: 49 89 11 mov %rdx,(%r9) 6: 41 8b 57 28 mov 0x28(%r15),%edx a: 45 8b 5f 34 mov 0x34(%r15),%r11d e: 49 c7 07 00 00 00 00 movq $0x0,(%r15) 15: 49 rex.WB [ 70.724561] RSP: 0018:ffff95ae85e6fb90 EFLAGS: 00000202 [ 70.724561] RAX: 0000000002000000 RBX: ffff95ae841de000 RCX: 0000000000000000 [ 70.724561] RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000001 [ 70.724561] RBP: ffff95ae85e6fbf8 R08: 0000000000000000 R09: ffff95b710a30000 [ 70.724561] R10: 0000000000000000 R11: bdf289445ce31881 R12: ffff95ae85e6fc58 [ 70.724561] R13: 0000000000000000 R14: 0000000000000040 R15: 0000000000000000 [ 70.724561] FS: 000000002c5c1380(0000) GS:ffff95bd7fcc0000(0000) knlGS:0000000000000000 [ 70.724561] CS: 0010 DS: 0000 ES: 0000 C ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Initialize get_bytes_per_element's default to 1 Variables, used as denominators and maybe not assigned to other values, should not be 0. bytes_per_element_y & bytes_per_element_c are initialized by get_bytes_per_element() which should never return 0. This fixes 10 DIVIDE_BY_ZERO issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: ext4: avoid use-after-free in ext4_ext_show_leaf() In ext4_find_extent(), path may be freed by error or be reallocated, so using a previously saved *ppath may have been freed and thus may trigger use-after-free, as follows: ext4_split_extent path = *ppath; ext4_split_extent_at(ppath) path = ext4_find_extent(ppath) ext4_split_extent_at(ppath) // ext4_find_extent fails to free path // but zeroout succeeds ext4_ext_show_leaf(inode, path) eh = path[depth].p_hdr // path use-after-free !!! Similar to ext4_split_extent_at(), we use *ppath directly as an input to ext4_ext_show_leaf(). Fix a spelling error by the way. Same problem in ext4_ext_handle_unwritten_extents(). Since 'path' is only used in ext4_ext_show_leaf(), remove 'path' and use *ppath directly. This issue is triggered only when EXT_DEBUG is defined and therefore does not affect functionality.

In the Linux kernel, the following vulnerability has been resolved: tpm: Clean up TPM space after command failure tpm_dev_transmit prepares the TPM space before attempting command transmission. However if the command fails no rollback of this preparation is done. This can result in transient handles being leaked if the device is subsequently closed with no further commands performed. Fix this by flushing the space in the event of command transmission failure.

In the Linux kernel, the following vulnerability has been resolved: nfsd: call cache_put if xdr_reserve_space returns NULL If not enough buffer space available, but idmap_lookup has triggered lookup_fn which calls cache_get and returns successfully. Then we missed to call cache_put here which pairs with cache_get. Reviwed-by: Jeff Layton <[email protected]>

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix spin_unlock_irqrestore() called with IRQs enabled Fix missuse of spin_lock_irq()/spin_unlock_irq() when spin_lock_irqsave()/spin_lock_irqrestore() was hold. This was discovered through the lock debugging, and the corresponding log is as follows: raw_local_irq_restore() called with IRQs enabled WARNING: CPU: 96 PID: 2074 at kernel/locking/irqflag-debug.c:10 warn_bogus_irq_restore+0x30/0x40 ... Call trace: warn_bogus_irq_restore+0x30/0x40 _raw_spin_unlock_irqrestore+0x84/0xc8 add_qp_to_list+0x11c/0x148 [hns_roce_hw_v2] hns_roce_create_qp_common.constprop.0+0x240/0x780 [hns_roce_hw_v2] hns_roce_create_qp+0x98/0x160 [hns_roce_hw_v2] create_qp+0x138/0x258 ib_create_qp_kernel+0x50/0xe8 create_mad_qp+0xa8/0x128 ib_mad_port_open+0x218/0x448 ib_mad_init_device+0x70/0x1f8 add_client_context+0xfc/0x220 enable_device_and_get+0xd0/0x140 ib_register_device.part.0+0xf4/0x1c8 ib_register_device+0x34/0x50 hns_roce_register_device+0x174/0x3d0 [hns_roce_hw_v2] hns_roce_init+0xfc/0x2c0 [hns_roce_hw_v2] __hns_roce_hw_v2_init_instance+0x7c/0x1d0 [hns_roce_hw_v2] hns_roce_hw_v2_init_instance+0x9c/0x180 [hns_roce_hw_v2]

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: always wait for both firmware loading attempts In 'rtw_wait_firmware_completion()', always wait for both (regular and wowlan) firmware loading attempts. Otherwise if 'rtw_usb_intf_init()' has failed in 'rtw_usb_probe()', 'rtw_usb_disconnect()' may issue 'ieee80211_free_hw()' when one of 'rtw_load_firmware_cb()' (usually the wowlan one) is still in progress, causing UAF detected by KASAN.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: use two-phase skb reclamation in ieee80211_do_stop() Since '__dev_queue_xmit()' should be called with interrupts enabled, the following backtrace: ieee80211_do_stop() ... spin_lock_irqsave(&local->queue_stop_reason_lock, flags) ... ieee80211_free_txskb() ieee80211_report_used_skb() ieee80211_report_ack_skb() cfg80211_mgmt_tx_status_ext() nl80211_frame_tx_status() genlmsg_multicast_netns() genlmsg_multicast_netns_filtered() nlmsg_multicast_filtered() netlink_broadcast_filtered() do_one_broadcast() netlink_broadcast_deliver() __netlink_sendskb() netlink_deliver_tap() __netlink_deliver_tap_skb() dev_queue_xmit() __dev_queue_xmit() ; with IRQS disabled ... spin_unlock_irqrestore(&local->queue_stop_reason_lock, flags) issues the warning (as reported by syzbot reproducer): WARNING: CPU: 2 PID: 5128 at kernel/softirq.c:362 __local_bh_enable_ip+0xc3/0x120 Fix this by implementing a two-phase skb reclamation in 'ieee80211_do_stop()', where actual work is performed outside of a section with interrupts disabled.

In the Linux kernel, the following vulnerability has been resolved: ipv6: avoid possible NULL deref in rt6_uncached_list_flush_dev() Blamed commit accidentally removed a check for rt->rt6i_idev being NULL, as spotted by syzbot: Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] CPU: 1 UID: 0 PID: 10998 Comm: syz-executor Not tainted 6.11.0-rc6-syzkaller-00208-g625403177711 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024 RIP: 0010:rt6_uncached_list_flush_dev net/ipv6/route.c:177 [inline] RIP: 0010:rt6_disable_ip+0x33e/0x7e0 net/ipv6/route.c:4914 Code: 41 80 3c 04 00 74 0a e8 90 d0 9b f7 48 8b 7c 24 08 48 8b 07 48 89 44 24 10 4c 89 f0 48 c1 e8 03 48 b9 00 00 00 00 00 fc ff df <80> 3c 08 00 74 08 4c 89 f7 e8 64 d0 9b f7 48 8b 44 24 18 49 39 06 RSP: 0018:ffffc900047374e0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 1ffff1100fdf8f33 RCX: dffffc0000000000 RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffff88807efc78c0 RBP: ffffc900047375d0 R08: 0000000000000003 R09: fffff520008e6e8c R10: dffffc0000000000 R11: fffff520008e6e8c R12: 1ffff1100fdf8f18 R13: ffff88807efc7998 R14: 0000000000000000 R15: ffff88807efc7930 FS: 0000000000000000(0000) GS:ffff8880b8900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020002a80 CR3: 0000000022f62000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> addrconf_ifdown+0x15d/0x1bd0 net/ipv6/addrconf.c:3856 addrconf_notify+0x3cb/0x1020 notifier_call_chain+0x19f/0x3e0 kernel/notifier.c:93 call_netdevice_notifiers_extack net/core/dev.c:2032 [inline] call_netdevice_notifiers net/core/dev.c:2046 [inline] unregister_netdevice_many_notify+0xd81/0x1c40 net/core/dev.c:11352 unregister_netdevice_many net/core/dev.c:11414 [inline] unregister_netdevice_queue+0x303/0x370 net/core/dev.c:11289 unregister_netdevice include/linux/netdevice.h:3129 [inline] __tun_detach+0x6b9/0x1600 drivers/net/tun.c:685 tun_detach drivers/net/tun.c:701 [inline] tun_chr_close+0x108/0x1b0 drivers/net/tun.c:3510 __fput+0x24a/0x8a0 fs/file_table.c:422 task_work_run+0x24f/0x310 kernel/task_work.c:228 exit_task_work include/linux/task_work.h:40 [inline] do_exit+0xa2f/0x27f0 kernel/exit.c:882 do_group_exit+0x207/0x2c0 kernel/exit.c:1031 __do_sys_exit_group kernel/exit.c:1042 [inline] __se_sys_exit_group kernel/exit.c:1040 [inline] __x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1040 x64_sys_call+0x2634/0x2640 arch/x86/include/generated/asm/syscalls_64.h:232 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f1acc77def9 Code: Unable to access opcode bytes at 0x7f1acc77decf. RSP: 002b:00007ffeb26fa738 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1acc77def9 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000043 RBP: 00007f1acc7dd508 R08: 00007ffeb26f84d7 R09: 0000000000000003 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000001 R13: 0000000000000003 R14: 00000000ffffffff R15: 00007ffeb26fa8e0 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010:rt6_uncached_list_flush_dev net/ipv6/route.c:177 [inline] RIP: 0010:rt6_disable_ip+0x33e/0x7e0 net/ipv6/route.c:4914 Code: 41 80 3c 04 00 74 0a e8 90 d0 9b f7 48 8b 7c 24 08 48 8b 07 48 89 44 24 10 4c 89 f0 48 c1 e8 03 48 b9 00 00 00 00 00 fc ff df <80> 3c 08 00 74 08 4c 89 f7 e8 64 d0 9b f7 48 8b 44 24 18 49 39 06 RSP: 0018:ffffc900047374e0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 1ffff1100fdf8f33 RCX: dffffc0000000000 RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffff88807efc78c0 R ---truncated---

In the Linux kernel, the following vulnerability has been resolved: block: fix potential invalid pointer dereference in blk_add_partition The blk_add_partition() function initially used a single if-condition (IS_ERR(part)) to check for errors when adding a partition. This was modified to handle the specific case of -ENXIO separately, allowing the function to proceed without logging the error in this case. However, this change unintentionally left a path where md_autodetect_dev() could be called without confirming that part is a valid pointer. This commit separates the error handling logic by splitting the initial if-condition, improving code readability and handling specific error scenarios explicitly. The function now distinguishes the general error case from -ENXIO without altering the existing behavior of md_autodetect_dev() calls.