CVE Feed

In the Linux kernel, the following vulnerability has been resolved: hwmon: (corsair-psu) Stop device IO before calling hid_hw_stop hid_hw_stop() does not stop the device IO. This results in a race condition between hid_input_report() and the point immediately following the execution of hid_device_io_start() within corsairpsu_probe(). If the probe operation fails after "io start" has been initiated, this race condition will result in a uaf vulnerability [1]. CPU0 CPU1 ==== ==== corsairpsu_probe() hid_device_io_start() ... unlock driver_input_lock hid_hw_stop() kfree(hidraw) __hid_input_report() ... acquire driver_input_lock hid_report_raw_event() hidraw_report_event() ... access hidraw's list_lock // trigger uaf Consequently, when corsairpsu_probe() fails and hid_hw_stop() needs to be executed, the io_started flag is first cleared while holding the driver_input_lock to prevent potential race conditions involving input reports. [1] BUG: KASAN: slab-use-after-free in rt_spin_lock+0x83/0x400 kernel/locking/spinlock_rt.c:56 Call Trace: hidraw_report_event+0x5d/0x3a0 drivers/hid/hidraw.c:577 hid_report_raw_event+0x311/0x1730 drivers/hid/hid-core.c:2076 __hid_input_report drivers/hid/hid-core.c:2152 [inline] hid_input_report+0x44e/0x580 drivers/hid/hid-core.c:2174 hid_irq_in+0x47e/0x6d0 drivers/hid/usbhid/hid-core.c:286 __usb_hcd_giveback_urb+0x3b3/0x5e0 drivers/usb/core/hcd.c:1657 dummy_timer+0x8a9/0x47d0 drivers/usb/gadget/udc/dummy_hcd.c:2005 Allocated by task 10: hidraw_connect+0x57/0x430 drivers/hid/hidraw.c:606 hid_connect+0x5bf/0x19d0 drivers/hid/hid-core.c:2277 hid_hw_start+0xa8/0x120 drivers/hid/hid-core.c:2387 corsairpsu_probe+0xd9/0x3c0 drivers/hwmon/corsair-psu.c:782 Freed by task 10: hidraw_disconnect+0x4f/0x60 drivers/hid/hidraw.c:662 hid_disconnect drivers/hid/hid-core.c:2362 [inline] hid_hw_stop+0x101/0x1e0 drivers/hid/hid-core.c:2407 corsairpsu_probe+0x327/0x3c0 drivers/hwmon/corsair-psu.c:826 Fix the problem by calling hid_device_io_stop() before calling hid_hw_stop(). [groeck: Updated subject and description; call hid_device_io_stop() only if IO has been started]

In the Linux kernel, the following vulnerability has been resolved: wan: wanxl: Only reset hardware after BAR mapping wanxl_pci_init_one() stores the freshly allocated card in driver data before the PLX BAR is mapped. Several early probe failures then unwind through wanxl_pci_remove_one(), including failure to allocate the coherent status area or to restore the DMA mask. wanxl_pci_remove_one() unconditionally calls wanxl_reset(), and wanxl_reset() dereferences card->plx. On those early failures card->plx is still NULL, so the error path can dereference a NULL MMIO pointer. Only issue the hardware reset once the BAR mapping exists. The remaining cleanup in wanxl_pci_remove_one() already checks whether later resources were allocated. This issue was found by a static analysis checker and confirmed by manual source review.

In the Linux kernel, the following vulnerability has been resolved: tipc: fix u16 MTU truncation in media and bearer MTU validation Both TIPC_NL_MEDIA_SET and TIPC_NL_BEARER_SET accept user-supplied MTU values but only enforce a minimum bound, not a maximum. When a user sets the MTU to a value exceeding U16_MAX (65535), it passes validation but is silently truncated when assigned to u16 fields l->mtu and l->advertised_mtu in tipc_link_create(). Values like 65536 (0x10000) truncate to 0, causing a division by zero in tipc_link_set_queue_limits() which computes TIPC_MAX_PUBL / (l->mtu / ITEM_SIZE). Other overflowing values (e.g. 65537-131071) produce small incorrect MTU values, resulting in link malfunction behaviors. Crash stack (triggered as unprivileged user via user namespace): tipc_link_set_queue_limits net/tipc/link.c:2531 tipc_link_create net/tipc/link.c:520 tipc_node_check_dest net/tipc/node.c:1279 tipc_disc_rcv net/tipc/discover.c:252 tipc_rcv net/tipc/node.c:2129 tipc_udp_recv net/tipc/udp_media.c:392 Two independent paths lack the upper bound check: 1. tipc_udp_mtu_bad() -- called from __tipc_nl_media_set() (MEDIA_SET) 2. inline check in __tipc_nl_bearer_set() at bearer.c:1160 (BEARER_SET) Fix both by rejecting MTU values above U16_MAX.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Check bounds in allocate_event_notification_slot The valid event ids go from 0 to KFD_SIGNAL_EVENT_LIMIT allocate_event_notification_slot has an option to specify an event id to allocate at, used by CRIU. We weren't checking the bounds on that value. Check them. v2: Lower bounds check is unecessary because of idr_alloc already rejecting negative numbers. Upper bounds check should be KFD_SIGNAL_EVENT_LIMIT since the signal mode mappings might not yet exist (cherry picked from commit 6853f1f6cbbeb3f53ebbbd7286536aeb2c5d5f50)

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix bo->pin leaking in amdgpu_bo_create_reserved amdgpu_bo_create_reserved() only allocates a new BO when *bo_ptr (struct amdgpu_bo **bo_ptr as input parameter) is NULL, it simply skips creation when *bo_ptr is non-NULL. But it unconditionally reserves, pins, gart allocates and maps the BO afterwards. When the same non-NULL BO pointer is passed in again, for example firmware buffers that live in adev and are re-loaded on every resume / cp_resume / start under AMDGPU_FW_LOAD_DIRECT, amdgpu_bo_pin() just increases pin_count unconditionally, however the matching teardown only unpins once, so pin_count never drops to zero, so TTM is not able to move, swap or evict a BO, causing BO leaks. This commit fixes this issue by only pinning the bo once at creation, and repeated calls no longer take additional pin references. (cherry picked from commit 3ddc0ae76202c447b6aec61e907b852bc94671cf)

In the Linux kernel, the following vulnerability has been resolved: media: cx231xx: fix devres lifetime USB drivers bind to USB interfaces and any device managed resources should have their lifetime tied to the interface rather than parent USB device. This avoids issues like memory leaks when drivers are unbound without their devices being physically disconnected (e.g. on probe deferral or configuration changes). Fix the driver state lifetime so that it is released on driver unbind.

In the Linux kernel, the following vulnerability has been resolved: media: cx23885: add ioremap return check and cleanup Add a check for the return value of pci_ioremap_bar() in cx23885_dev_setup(). If ioremap for BAR0 fails, release the already allocated PCI memory region, decrement the device count, and return -ENODEV. This prevents a potential null pointer dereference and ensures proper cleanup on memory mapping failure.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath6kl: fix OOB access from firmware ADDBA window size aggr_recv_addba_req_evt() logs a debug message when the firmware-supplied win_sz is outside [AGGR_WIN_SZ_MIN, AGGR_WIN_SZ_MAX] but does not return. The out-of-range win_sz is then used in TID_WINDOW_SZ() to compute a kzalloc size and stored in rxtid->hold_q_sz, leading to zero-size or overflowed allocations and subsequent out-of-bounds access. Clean up any previously active aggregation session for the TID first, then return early when win_sz is out of the valid range, instead of proceeding with a broken allocation size.

In the Linux kernel, the following vulnerability has been resolved: libceph: Fix multiplication overflow in decode_new_up_state_weight() If a message of type CEPH_MSG_OSD_MAP contains a (maliciously) corrupted osdmap, out-of-bounds memory accesses may occur in decode_new_up_state_weight(). This happens because the bounds check for the new_state part is based on calculating its length depending on a len value read from the incoming message. This calculation may overflow leading to an incorrect bounds check. Subsequently, out-of-bounds reads may occur when decoding this part. This patch switches the multiplication to use check_mul_overflow() to abort processing the osdmap if an overflow occurred. Therefore, osdmaps/messages containing large values for len that result in a multiplication overflow are treated as invalid. [ idryomov: rename new_state_len -> new_state_item_size, formatting ]

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix lifetime issue of amdgpu_vm_get_task_info_pasid() The vm pointer returned from amdgpu_vm_get_vm_from_pasid() is only valid while the lock is still being held. Once xa_unlock_irqrestore is called and returned, the pointer is no longer under lock and is subject to modification. Since, the caller still dereferences vm->task_info in amdgpu_vm_get_task_info_vm() after the lock is removed, this causes a use after unlock problem. Remove the lifetime issue present in amdgpu_vm_get_task_info_pasid() through removing the amdgpu_vm_get_vm_from_pasid() function from amdgpu_vm.c and making the relevant code inline to hold the lock while it is still in use. (cherry picked from commit 9d01579f3f868b333acc901815972685989092c7)

In the Linux kernel, the following vulnerability has been resolved: fscrypt: Avoid dynamic allocation in fscrypt_get_devices() When a blk_crypto_key starts being used or is evicted, fs/crypto/ calls fscrypt_get_devices() to get the filesystem's list of block devices, then iterates over them and calls blk_crypto_config_supported(), blk_crypto_start_using_key(), or blk_crypto_evict_key() on each one. Currently, the block device pointers are placed in a dynamically allocated array. This dynamic allocation is problematic because: - It can fail, especially at the fscrypt_destroy_inline_crypt_key() call site when it's invoked for inode eviction under direct reclaim. - fscrypt_destroy_inline_crypt_key() doesn't handle the failure. It just zeroizes and frees the blk_crypto_key without calling blk_crypto_evict_key(). That causes a use-after-free. For now, let's fix this in the straightforward and easily-backportable way by switching to an on-stack array. Currently the fscrypt multi-device functionality is used only by f2fs, which has a hardcoded limit of 8 block devices. An on-stack array works fine for that. (Of course, this solution won't scale up to large number of block devices. For that we'd need a different solution, like moving the block device iteration into the filesystem. Or in the case of btrfs, which will only support blk-crypto-fallback, we should make it just call blk-crypto-fallback directly, so the block devices won't be needed.)

In the Linux kernel, the following vulnerability has been resolved: mctp: serial: handle zero-length frames to prevent rx buffer overflow The MCTP serial receive state machine reads a frame length byte in mctp_serial_push_header() case 2 and validates it upper-bound-only: if (c > MCTP_SERIAL_FRAME_MTU) { dev->rxstate = STATE_ERR; } else { dev->rxlen = c; dev->rxpos = 0; dev->rxstate = STATE_DATA; ... } A length of zero passes this check, so rxlen is set to 0 and the state machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the incoming byte is stored and rxpos incremented before the terminator is dev->rxbuf[dev->rxpos] = c; dev->rxpos++; dev->rxstate = STATE_DATA; if (dev->rxpos == dev->rxlen) { dev->rxpos = 0; dev->rxstate = STATE_TRAILER; } With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is already 1 on the first data byte), so subsequent bytes are written past the end of the fixed 74-byte rxbuf, which is the last member of the netdev private area. Every following data byte is an attacker-controlled 1-byte out-of-bounds heap write, and the overflow continues until a frame (0x7e) or escape byte resets the parser -- effectively unbounded. Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line discipline and bring the resulting mctpserialN netdev up, after which the bytes arrive via the tty receive path. Route a zero-length frame straight to STATE_TRAILER instead of STATE_DATA. The trailer/framing bytes are still consumed, and the frame resolves to a zero-length skb that the MCTP core rejects; the parser never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can no longer occur. KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this change): UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370 index 74 is out of range for type 'u8 [74]' BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf Write of size 1 at addr ... by task kworker/u16:0 mctp_serial_tty_receive_buf tty_ldisc_receive_buf flush_to_ldisc Allocated by task 152: alloc_netdev_mqs mctp_serial_open v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so the trailer/framing bytes are still consumed (Jeremy Kerr). Found by 0sec automated security-research tooling (https://0sec.ai).

In the Linux kernel, the following vulnerability has been resolved: openvswitch: fix GSO userspace truncation underflow OVS_ACTION_ATTR_TRUNC currently stores a delta from the original skb length in OVS_CB(skb)->cutlen. When a later userspace action segments a GSO skb, queue_gso_packets() reuses that delta for each smaller segment. A segment can then reach queue_userspace_packet() with cutlen greater than skb->len, underflowing the length passed to skb_zerocopy(). Store the maximum preserved length instead and bound each consumer against the current skb length. Use U32_MAX as the no-truncation sentinel so the value remains valid if skb geometry changes before a consumer handles it.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: cancel sched scan results work on unregister cfg80211_sched_scan_results() can queue rdev->sched_scan_res_wk from a driver result notification while a scheduled scan request is present. The work callback recovers the containing cfg80211_registered_device and then locks the wiphy and walks the scheduled-scan request list. wiphy_unregister() already makes the wiphy unreachable and drains rdev work items before cfg80211_dev_free() can release the object, but it does not drain sched_scan_res_wk. A queued or running result work item can therefore cross the unregister/free boundary and access freed rdev state. The buggy scenario involves two paths, with each column showing the order within that path: scheduled-scan result path: unregister/free path: 1. cfg80211_sched_scan_results() 1. interface teardown stops and queues rdev->sched_scan_res_wk. removes the scheduled scan request. 2. cfg80211_wq starts the work 2. wiphy_unregister() drains other item and recovers rdev. rdev work items. 3. The worker locks rdev->wiphy 3. cfg80211_dev_free() destroys and and walks rdev state. frees rdev. Cancel sched_scan_res_wk in wiphy_unregister() alongside the other rdev work items. cancel_work_sync() removes a pending result notification and waits for an already running callback, so cfg80211_dev_free() cannot free rdev while this work item is still active. Validation reproduced this kernel report: BUG: KASAN: use-after-free in cfg80211_sched_scan_results_wk+0x4a6/0x530 Workqueue: cfg80211 cfg80211_sched_scan_results_wk [cfg80211] Read of size 8 Call trace: dump_stack_lvl+0x66/0xa0 print_report+0xce/0x630 cfg80211_sched_scan_results_wk+0x4a6/0x530 srso_alias_return_thunk+0x5/0xfbef5 __virt_addr_valid+0x224/0x430 kasan_report+0xac/0xe0 lockdep_hardirqs_on_prepare+0xea/0x1a0 process_one_work+0x8d0/0x18f0 (kernel/workqueue.c:3212) lock_is_held_type+0x8f/0x100 worker_thread+0x5ad/0xfd0 __kthread_parkme+0xc6/0x200 kthread+0x31e/0x410 trace_hardirqs_on+0x1a/0x170 ret_from_fork+0x576/0x810 __switch_to+0x57e/0xe20 __switch_to_asm+0x33/0x70 ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: dummy_hcd: prevent fifo_req reuse during giveback dummy_hcd embeds a single shared usb_request (dum->fifo_req) that the "emulated single-request FIFO" fast-path in dummy_queue() reuses for small IN transfers: it copies the caller's request into it (req->req = *_req) and queues it, treating list_empty(&fifo_req.queue) as "the slot is free". The completion side (dummy_timer/transfer/nuke/dummy_dequeue) follows the standard pattern: list_del_init(&req->queue) unlinks the request, then the lock is dropped and usb_gadget_giveback_request() invokes req->complete(). But list_del_init() makes fifo_req.queue look empty *before* the completion callback returns, so a concurrent dummy_queue() on another CPU sees the slot as free, reuses fifo_req and runs req->req = *_req -- overwriting req->complete while dummy_timer is mid-calling it. The indirect call then jumps to a clobbered pointer, causing a general protection fault / page fault in dummy_timer (syzkaller extid faf3a6cf579fc65591ca). The clobbering write is an in-bounds memcpy on a live shared object, so KASAN cannot flag it. Add a fifo_req_busy bit covering the shared request's whole lifetime: set it in dummy_queue() when the FIFO fast-path takes fifo_req (making it the fast-path guard, replacing the list_empty(&fifo_req.queue) test), and clear it after the completion callback has returned, via a dummy_giveback() helper used at all four gadget-request giveback sites. The shared slot can no longer be reused until its completion callback has finished.

In the Linux kernel, the following vulnerability has been resolved: hwmon: occ: validate poll response sensor blocks The OCC poll response parser walks a counted list of sensor data blocks. It used the static backing-array capacity as the parse boundary, but a transport response makes only data_length bytes current and valid. A truncated response can therefore make the parser consume a block header or block extent outside the current response. Use data_length as the parent boundary, prove the fixed poll header and each current block header before reading them, and prove the complete block before advancing. Keep parsed sensor metadata local until the complete response has passed validation, then publish it. Propagate malformed-response errors before publishing the OCC as active.

In the Linux kernel, the following vulnerability has been resolved: net: mctp i3c: clean up notifier and buses if driver register fails mctp_i3c_mod_init() registers the I3C bus notifier and then walks the existing buses with i3c_for_each_bus_locked(mctp_i3c_bus_add_new, NULL) before registering the I3C device driver. If i3c_driver_register() fails, the function returns the error directly, leaving the notifier registered and every mctp_i3c_bus object created for the existing buses allocated. The notifier is left pointing into the module that failed to load and the bus list is leaked. Mirror the module exit path on this failure: unregister the notifier and tear down the buses that were added before returning the error. This issue was identified during our ongoing static-analysis research while reviewing kernel code.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/vm: Fix SVM leak on resv obj alloc failure in xe_vm_create() Commit 9e9787414882 ("drm/xe/userptr: replace xe_hmm with gpusvm") made xe_svm_init() unconditional in xe_vm_create() and extended it to also initialize a "simple" gpusvm state for non-fault-mode VMs. The matching xe_svm_fini() call in xe_vm_close_and_put() was updated to run unconditionally, but the error unwind path in xe_vm_create() was not. On the drm_gpuvm_resv_object_alloc() failure path, xe_svm_init() has already succeeded but xe_svm_fini() is only called when XE_VM_FLAG_FAULT_MODE is set. For non-fault-mode VMs this leaves vm->svm.gpusvm partially initialized and leaks the resources allocated by drm_gpusvm_init(). For fault-mode VMs, xe_svm_init() additionally acquires the pagemap owner via drm_pagemap_acquire_owner() and the pagemaps via xe_svm_get_pagemaps(). Those resources are released by xe_svm_close(), not xe_svm_fini(). On the same error path, xe_svm_close() is not called either, so fault-mode VMs leak the pagemap owner and pagemaps. Fix both leaks: - Call xe_svm_fini() unconditionally on the err_svm_fini path, matching the unconditional xe_svm_init() call. Move the vm->size = 0 assignment out of the conditional so the xe_vm_is_closed() assert in xe_svm_fini() (and xe_svm_close()) holds for both modes. - Call xe_svm_close() for fault-mode VMs before xe_svm_fini(), matching the ordering used in xe_vm_close_and_put(). (cherry picked from commit ca2a3587d577ba764e0fe628fb676244fc33ddd4)

In the Linux kernel, the following vulnerability has been resolved: media: v4l2-ctrls: validate HEVC active reference counts HEVC slice parameters are shared stateless V4L2 controls, but the common validation path does not verify the active L0/L1 reference counts before driver-specific code consumes them. The original report came from Cedrus, but the active count bounds are not Cedrus-specific. Validate them in the common HEVC slice control path so stateless HEVC drivers get the same basic guarantees as soon as the control is queued. Do not reject ref_idx_l0/ref_idx_l1 entries here. Existing userspace may use out-of-range sentinel values such as 0xff for missing references, and some hardware can use that information for concealment. Keep this common check limited to the active reference counts.

In the Linux kernel, the following vulnerability has been resolved: ALSA: timer: drain a slave's callback before its master detaches it snd_timer_close_locked() drains the closing instance's own in-flight callback (IFLG_CALLBACK) before freeing it, but not its slaves'. When a master instance is closed, remove_slave_links() clears each slave's ->timer; the slave's own close then reads timer == NULL and takes the branch that skips the drain entirely (snd_timer_stop_slave() also no-ops on a NULL timer). So a slave whose callback is still running when the master is closed is freed underneath the live callback, leading to use-after-free. Drain the slaves too before remove_slave_links() severs them. snd_timer_stop() has already taken this instance off the active list, so no new slave callback can be queued. Take the slaves off the ack list so a pending one can't fire either, then wait for any that is already in flight.

In the Linux kernel, the following vulnerability has been resolved: misc: nsm: only unlock nsm_dev on post-lock error paths nsm_dev_ioctl() jumps to the common out label even when the initial copy_from_user() fails before nsm->lock has been taken. The error path then blindly unlocks a mutex that was never acquired. This issue was found by our static analysis tool and then manually reviewed against the current tree. The grounded PoC kept the miscdevice ioctl entry and the pre-lock copy_from_user(&raw, argp, _IOC_SIZE(cmd)) failure path by issuing NSM_IOCTL_RAW with an invalid user pointer. That failure reaches the shared out label before mutex_lock(&nsm->lock). Lockdep reported: WARNING: bad unlock balance detected! exploit/193 is trying to release lock (&global_nsm.lock) at: nsm_dev_ioctl+0x5f/0xcf [vuln_msv] but there are no more locks to release! no locks held by exploit/193. Return immediately on the pre-lock copy_from_user() failure and keep the common unlock label for the post-lock paths only.

In the Linux kernel, the following vulnerability has been resolved: libceph: remove debugfs files before client teardown ceph_destroy_client() tears down the monitor client before removing the per-client debugfs files. A concurrent read of the monmap debugfs file can enter monmap_show() after ceph_monc_stop() has freed monc->monmap, triggering a use-after-free. Remove the debugfs files before stopping the OSD and monitor clients. debugfs_remove() drains active handlers and prevents new accesses, so the debugfs callbacks can no longer race the rest of client teardown.

In the Linux kernel, the following vulnerability has been resolved: media: amlogic-c3: Add validations for ae and awb config Avoid invalid memory access if the zones_num is bigger than zone_weight. This patch fixes the following smatch errors: drivers/media/platform/amlogic/c3/isp/c3-isp-params.c:111 c3_isp_params_awb_wt() error: buffer overflow 'cfg->zone_weight' 768 <= u32max drivers/media/platform/amlogic/c3/isp/c3-isp-params.c:111 c3_isp_params_awb_wt() error: buffer overflow 'cfg->zone_weight' 768 <= u32max drivers/media/platform/amlogic/c3/isp/c3-isp-params.c:227 c3_isp_params_ae_wt() error: buffer overflow 'cfg->zone_weight' 255 <= u32max drivers/media/platform/amlogic/c3/isp/c3-isp-params.c:227 c3_isp_params_ae_wt() error: buffer overflow 'cfg->zone_weight' 255 <= u32max

In the Linux kernel, the following vulnerability has been resolved: rtase: Workaround for TX hang caused by hardware packet parsing The hardware performs packet parsing before packet transmission. Parsing incomplete IPv4, IPv6, TCP, or UDP headers may trigger a TX hang because the hardware parser expects additional protocol header data that is not present in the packet. The hardware performs additional PTP parsing on UDP packets identified by destination ports 319/320 at the expected UDP destination port offset. If such a packet has transport data smaller than RTASE_MIN_PAD_LEN, the hardware parser expects additional packet data and may trigger a TX hang. To avoid these hardware issues, the driver applies the following workarounds. Drop malformed packets that may trigger this hardware issue before transmission. For IPv4 non-initial fragments, the hardware does not check the fragment offset before parsing the expected transport header location. As a result, these packets are still subject to transport header parsing even though they do not contain a transport header. If the transport data is shorter than the minimum transport header required by the hardware parser, pad the transport data to the minimum transport header length required by the hardware parser. Packets that also match the hardware PTP parsing conditions continue to follow the corresponding workaround. For IPv6 fragmented packets, neither of the above hardware issues occurs because the hardware only continues packet parsing when the IPv6 Base Header Next Header field directly indicates UDP. Packets carrying a Fragment Header do not continue through the subsequent packet parsing stages. For packets identified for hardware PTP parsing, pad the transport data so it reaches RTASE_MIN_PAD_LEN before transmission.

In the Linux kernel, the following vulnerability has been resolved: vxlan: mdb: Fix source list corruption on a failed replace When replacing the source list of an MDB remote entry, all existing sources are first marked for deletion and vxlan_mdb_remote_srcs_add() is then called to add the new source list. Sources present in the new list have their deletion mark cleared, and any sources left marked afterwards are removed. If vxlan_mdb_remote_srcs_add() fails partway through, its error path deletes all entries on the remote's source list. That rollback is only correct for its other caller, vxlan_mdb_remote_add(), where the remote was just allocated and the list contains solely entries added during the call. On the replace path the list also holds pre-existing sources, so a failed replace tears them down together with their (S, G) forwarding entries instead of leaving the entry unchanged. This is reachable from an existing (*, G) remote. An EXCLUDE filter that loses sources starts forwarding traffic that should be blocked, while an INCLUDE filter that loses sources drops traffic that should be forwarded. Mark entries created during the current pass with a new VXLAN_SGRP_F_NEW flag. On failure, delete only those entries and clear the deletion mark on the pre-existing ones, so a failed replace leaves the source list untouched. Retain the flag until the whole operation succeeds and then clear it. Also stop vxlan_mdb_remote_src_add() from deleting a pre-existing entry it only looked up when adding that entry's forwarding entry fails.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/vcn4: avoid rereading IB param length Reuse the parameter length returned by vcn_v4_0_enc_find_ib_param() instead of rereading it from the IB. This avoids a potential TOCTOU issue if the IB contents change between reads. (cherry picked from commit dbb02b4755f8c1f3773263f2d779872c1c0c073a)

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: reject mapping a reserved doorbell to a new queue When creating an user-queue, the user space provides a doorbell BO handle and an offset within the bo to obtain a doorbell. However current implementation using xa_store_irq() to store a doorbell, which allows a later queue created with the same BO and offset parameters to overwrite an existing queue and doorbell mapping. This can cause problems like misrouting fence IRQ processing to a wrong queue, and mislead the cleanup process of one queue erasing the mapping of another queue. This commit fixes this issue by replacing xa_store_irq with xa_insert_irq, which rejects mapping a reserved doorbell to a newly created queue (cherry picked from commit 6244eae22966350db52faf9c1369d3b2ffc5de4e)

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix context pstate override handling There are several problems in the context pstate handling code. The most serious ones are potential use-after-free and NULL pointer dereferences at context initialization time. Both are due amdgpu_ctx_init() not holding the adev->pm.stable_pstate_ctx_lock, which is otherwise used from both sysfs and the context code itself for modifying and clearing the stored context pointer. Second issue is that context fini can trample over the pstate configuration set via sysfs. This is due the restore state (ctx->stable_pstate) being saved at context init time, and not if, or when the context actually changes the pstate. As the context exits it will therefore incorrectly restore to what was set before the sysfs override was requested. The simplest fix is to drastically simplify how the state is tracked, by clearly defining the points at which pstate ownership is taken and released, and to handle all transitions under the correct lock. Instead of at context init time, the previous state is saved only at the point the context overrides the current state, and is restored on context exit only if the context is still the owner of the current override state. (cherry picked from commit 1b5e413713c0a93bc1818394d0ce49aaad21bd27)

In the Linux kernel, the following vulnerability has been resolved: media: meson: vdec: Fix memory leak in error path of vdec_open The vdec_open() function previously jumped directly to err_m2m_release when vdec_init_ctrls() failed, skipping release of the m2m context. This caused a resource leak. Fix it by introducing a proper err_m2m_ctx_release label that calls v4l2_m2m_ctx_release(sess->m2m_ctx) before releasing the m2m device. This was identified via kmemleak: unreferenced object 0xffff0000205d6878 (size 8): comm "v4l_id", pid 5289, jiffies 4294938580 hex dump (first 8 bytes): 40 d2 49 18 00 00 ff ff @.I..... backtrace (crc d3204599): kmemleak_alloc+0xc8/0xf0 __kvmalloc_node_noprof+0x60c/0x850 v4l2_ctrl_handler_init_class+0x1b4/0x2e8 [videodev] vdec_open+0x1f4/0x788 [meson_vdec] v4l2_open+0x144/0x460 [videodev] chrdev_open+0x1ac/0x500 do_dentry_open+0x3f0/0xfe8 vfs_open+0x68/0x320 do_open+0x2d8/0x9a8 path_openat+0x1d0/0x4f0 do_filp_open+0x190/0x380 do_sys_openat2+0xf8/0x1b0 __arm64_sys_openat+0x13c/0x1e8 invoke_syscall+0xdc/0x268 el0_svc_common.constprop.0+0x178/0x258 do_el0_svc+0x4c/0x70

In the Linux kernel, the following vulnerability has been resolved: media: nuvoton: npcm-video: fix memory leaks in probe and remove npcm_video_probe() allocates the npcm_video structure with kzalloc_obj() but never frees it on any probe error path or in npcm_video_remove(), leaking the allocation on every failed probe and every normal unbind. Additionally, when npcm_video_setup_video() fails, the reserved memory association established by of_reserved_mem_device_init() in npcm_video_init() is not released, leaking the rmem_assigned_device entry on the global list. Fix both by adding kfree(video) to all probe error paths and to npcm_video_remove(), and adding the missing of_reserved_mem_device_release() call when npcm_video_setup_video() fails.

In the Linux kernel, the following vulnerability has been resolved: media: nxp: imx8-isi: Add missing v4l2_subdev_cleanup() in crossbar and pipe Both mxc_isi_crossbar_init() and mxc_isi_pipe_init() call v4l2_subdev_init_finalize() which allocates the subdev active state, but neither mxc_isi_crossbar_cleanup() nor mxc_isi_pipe_cleanup() calls v4l2_subdev_cleanup() to free it. This causes a memory leak on every rmmod, reported by kmemleak: unreferenced object 0xffff0000d06fc800 (size 192): comm "(udev-worker)", pid 254, jiffies 4294913455 backtrace (crc 36eeae58): kmemleak_alloc+0x34/0x40 __kvmalloc_node_noprof+0x5f8/0x7d8 __v4l2_subdev_state_alloc+0x1fc/0x30c __v4l2_subdev_init_finalize+0x178/0x368 Add the missing v4l2_subdev_cleanup() calls before media_entity_cleanup() in both crossbar and pipe cleanup paths.

In the Linux kernel, the following vulnerability has been resolved: media: saa7134: Fix a possible memory leak in saa7134_video_init1 In saa7134_video_init1(), the return value of the first saa7134_pgtable_alloc() is not checked. If it fails, the function continues as if successful, leaving the driver with an invalid page table. Additionally, if vb2_queue_init() for the VBI queue fails after the video queue page table has been allocated, the allocated memory is not freed before returning. The second saa7134_pgtable_alloc() also lacks a return value check. Errors occur during device probing before the device is fully registered, the normal cleanup path in saa7134_finidev() is not executed, leading to memory leaks and potential use of uninitialized DMA resources. Check the return value of both saa7134_pgtable_alloc() calls and propagate errors. On failure of any later step, free allocated page tables to avoid memory leaks. Ensure control handlers are also released on error to prevent further resource leakage. Found by code review.

In the Linux kernel, the following vulnerability has been resolved: mei: bus: access mei_device under device_lock on cleanup Fix couple of problems in mei_cl_bus_dev_release(): mei_cl_flush_queues() is running without lock. bus->file_list access after mei_dev_bus_put(bus) can become a use-after-free if this was the last reference to bus. Protect queues cleanup and WARN traversal by device lock there to avoid the concurrent access problems. Move WARN traversal before mei_dev_bus_put(bus). This file uses bus variable name for mei_device, adjust code of mei_cl_bus_dev_release() to use bus variable too.

In the Linux kernel, the following vulnerability has been resolved: amt: re-read skb header pointers after every pull Several AMT receive and transmit paths cache a pointer into the skb head (ip_hdr(), ipv6_hdr(), eth_hdr() or the AMT message header) and then call a helper that can reallocate that head before the cached pointer is used again. pskb_may_pull(), ip_mc_may_pull(), ipv6_mc_may_pull(), iptunnel_pull_header(), ip_mc_check_igmp() and ipv6_mc_check_mld() can all free the old head and move the data, so a pointer taken before the call dangles afterwards and the later access is a use-after-free of the freed head. The affected sites are: amt_rcv() caches ip_hdr() before amt_parse_type() pulls, then reads iph->saddr. amt_dev_xmit() caches ip_hdr()/ipv6_hdr() before ip_mc_check_igmp()/ ipv6_mc_check_mld() and pskb_may_pull(), then reads the group address. amt_multicast_data_handler() caches eth_hdr() before pskb_may_pull(), then writes the L2 header. amt_membership_query_handler() caches the AMT header, the outer and inner eth_hdr() and ip_hdr() before iptunnel_pull_header() and several pulls, then reads and writes them. amt_igmpv3_report_handler() and amt_mldv2_report_handler() cache ip_hdr()/ipv6_hdr() and the current group record and read the record count from the report header inside the record loop, across the *_mc_may_pull() calls. amt_update_handler() caches ip_hdr() and the AMT membership-update header before pskb_may_pull(), iptunnel_pull_header(), ip_mc_check_igmp() and the report handler, then reads iph->daddr and amtmu->nonce / amtmu->response_mac. Fix each site by either snapshotting the scalar that is used after the pull before the first pull runs, or re-deriving the header pointer from the skb after the last pull that can move the head. Values that are stable across the pull (source and group address, the response MAC and nonce, the record count, the outer source MAC) are snapshotted; pointers that are written through or read repeatedly are re-derived.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/rtp: Add RING_FORCE_TO_NONPRIV_DENY to OA whitelists Unconditionally whitelisting OA registers is a security violation. Set RING_FORCE_TO_NONPRIV_DENY bit in OA nonpriv slots, so that OA registers don't get whitelisted by default after probe, gt reset, resume and engine reset. (cherry picked from commit 90511bdcfda97211c01f1d945d4ea616578d8fca)

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_ffa: Fix Endpoint Memory Access Descriptor offset calculation Use the descriptor's `ep_mem_offset` to calculate the start of the endpoint memory access array and to comply with the FF-A spec instead of defaulting to `sizeof(struct ffa_mem_region)`. This requires moving `ffa_mem_region_additional_setup()` earlier in the setup flow. Also, add sanity checks to ensure the calculated descriptor offsets do not exceed `max_fragsize`.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: hold hdev->lock for hci_conn_params lookups hci_conn_params_lookup requires hdev->lock be held, otherwise the list iteration or param access is not safe. Hold hdev->lock for params lookups in hci_sync.

In the Linux kernel, the following vulnerability has been resolved: mtd: fix double free and WARN_ON in add_mtd_device() error paths When device_register() or mtd_nvmem_add() fails inside add_mtd_device() for a partition, the error handling triggers mtd_release() via put_device() or device_unregister(). mtd_release() calls release_mtd_partition() which frees the mtd_info structure. However, callers such as mtd_add_partition() and add_mtd_partitions() also call free_partition() in their error paths, resulting in a double free. Additionally, release_mtd_partition() hits WARN_ON(!list_empty( &mtd->part.node)) because the partition node is still linked in the parent's partitions list when the release callback fires from the add_mtd_device() error path. Fix this by overriding dev->type and dev->release before put_device() in the error paths, so that device_release() invokes a no-op function instead of mtd_release(). For the mtd_nvmem_add() failure case, device_unregister() is replaced with device_del() to separate the device removal from the final kobject reference drop, allowing the override to take effect before put_device() is called. The callers' error paths (list_del + free_partition) remain the sole owners of mtd_info lifetime on add_mtd_device() failure, which is the expected contract. The normal partition teardown path is not affected: del_mtd_device() goes through kref_put() -> mtd_device_release() -> device_unregister() with dev->type still set to &mtd_devtype, so mtd_release() -> release_mtd_partition() continues to work correctly for the regular removal case.

In the Linux kernel, the following vulnerability has been resolved: watchdog: pretimeout: Fix UAF in watchdog_unregister_governor() When a watchdog governor is unregistered, it updates existing watchdog devices that were using this governor by falling back to `default_gov`. If the governor being unregistered is currently set as `default_gov`, the `default_gov` is never cleared. This leads to 2 use-after-free issues: 1. New watchdog devices registered after this point will inherit the dangling `default_gov`. 2. Existing watchdog devices using the unregistered governor will have their `wdd->gov` reassigned to the dangling `default_gov`. Fix the UAF by clearing `default_gov` if it matches the governor being unregistered.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211_hwsim: clamp virtio RX length before skb_put hwsim_virtio_rx_work() passes the virtqueue used-ring length reported by the device straight to skb_put() on a fixed-size receive skb. A backend reporting a length larger than the skb tailroom drives skb_put() past the buffer end and hits skb_over_panic() -- a host-triggerable guest panic (denial of service). Clamp the length to the skb's available room before skb_put(). A conforming device never reports more than the posted buffer size, so valid frames are unaffected; a truncated over-report then fails the length/header checks in hwsim_virtio_handle_cmd() and is dropped, so truncating rather than dropping here cannot be turned into a parsing problem.

In the Linux kernel, the following vulnerability has been resolved: smb/client: handle overlapping allocated ranges in fallocate smb3_simple_fallocate_range() can skip holes when an allocated range returned by the server starts before the current fallocate offset. The skipped hole is not zero-filled, but fallocate still returns success. A later write to that hole may therefore fail with ENOSPC. The function queries allocated ranges so that it can preserve existing contents and write zeroes only into holes. However, the server may return a range that starts before the current fallocate offset. For example, assume the fallocate request is [100, 400) and the only allocated range returned by the server is [0, 200): Request: [100, 400) Server range: [ 0, 200) allocated Correct: [100, 200) allocated data, skip [200, 400) hole, zero-fill Current: [100, 300) skipped [300, 400) zero-filled afterwards The current code adds the full server range length, 200, to the current offset 100 and moves to 300. As a result, the hole in [200, 300) is skipped without being zero-filled. Fix this by advancing only over the part of the allocated range that overlaps the current fallocate offset. Ignore ranges that end before the current offset and reject ranges whose end offset overflows. This also prevents a malformed range length from causing an out-of-bounds zero-buffer read.

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Prevent rereg_mr for non-mem regions When a QP/CQ/SRQ is created, a two step process is used where the buffer is allocated in userspace and explicitly registered with the normal reg_mr mechanism prior to creating the actual QP/CQ/SRQ object. These special registrations are indicated via an ABI field so the driver knows that they do not have a valid mkey and to skip the actual CQP command submission. Since these are real MR objects from the core's perspective, it is possible for a user application to invoke rereg_mr on them and cause a real CQP op to be emitted with the zero-initialized mkey value of 0. Fix this by preventing rereg_mr on these special regions.

In the Linux kernel, the following vulnerability has been resolved: usb: atm: ueagle-atm: reject descriptors that confuse probe and disconnect uea_probe() distinguishes a pre-firmware device from a post-firmware one using the USB id (UEA_IS_PREFIRM()), and stores a different object as the interface data in each case: a 'struct completion' for a pre-firmware device (to be waited on in .disconnect()), or a 'struct usbatm_data' for a post-firmware one. uea_disconnect() instead tells the two apart by the number of interfaces of the active configuration (a pre-firmware device exposes a single interface, ADI930 has 2 and eagle has 3), and casts the interface data accordingly. Because the two handlers use different criteria, a crafted device that advertises a pre-firmware id together with a multi-interface descriptor (or a post-firmware id with a single interface) makes them disagree: the small 'struct completion' stored by uea_probe() is then passed to usbatm_usb_disconnect(), which casts it to 'struct usbatm_data' and takes instance->serialize, reading past the end of the allocation: BUG: KASAN: slab-out-of-bounds in __mutex_lock+0x152a/0x1b80 Read of size 8 at addr ffff8880470e2c60 by task kworker/1:2/982 ... __mutex_lock+0x152a/0x1b80 usbatm_usb_disconnect+0x70/0x820 uea_disconnect+0x133/0x2c0 usb_unbind_interface+0x1dd/0x9e0 ... which belongs to the cache kmalloc-96 of size 96 The buggy address is located 0 bytes to the right of allocated 96-byte region [ffff8880470e2c00, ffff8880470e2c60) Reject such inconsistent descriptors in uea_probe() so that both handlers always make the same pre/post-firmware decision.

In the Linux kernel, the following vulnerability has been resolved: sctp: auth: verify auth requirement when auth_chunk is NULL sctp_auth_chunk_verify() returns true unconditionally when chunk->auth_chunk is NULL, silently skipping authentication. This is incorrect when: 1. skb_clone() failed in the BH receive path, leaving auth_chunk NULL. In sctp_endpoint_bh_rcv() asoc is NULL for new connections, so the early sctp_auth_recv_cid() check cannot catch this. 2. No AUTH chunk precedes COOKIE-ECHO, so skb_clone() is never called and auth_chunk remains NULL. Fix by checking sctp_auth_recv_cid() when auth_chunk is NULL: if authentication is required, return false to drop the chunk; otherwise continue normally.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix MCIA register buffer overflow on 32 dword reads The MCIA register can return up to 32 dwords (128 bytes) when the device advertises the mcia_32dwords capability, but struct mlx5_ifc_mcia_reg_bits only defines dword_0..11, leaving room for just 12 dwords (48 bytes) of data. mlx5_query_mcia() clamps the read size to mlx5_mcia_max_bytes() and then memcpy()s that many bytes out of the register, potentially reading past the end of the 'out' buffer. On kernels built with FORTIFY_SOURCE this is caught as a buffer overflow while reading the module EEPROM via ethtool: detected buffer overflow in memcpy kernel BUG at lib/string_helpers.c:1048! RIP: 0010:fortify_panic+0x13/0x20 Call Trace: mlx5_query_mcia.isra.0+0x200/0x210 [mlx5_core] mlx5_query_module_eeprom_by_page+0x4a/0xa0 [mlx5_core] mlx5e_get_module_eeprom_by_page+0xbb/0x120 [mlx5_core] eeprom_prepare_data+0xf3/0x170 ethnl_default_doit+0xf1/0x3b0 Extend the mcia_reg layout to 32 dwords.

In the Linux kernel, the following vulnerability has been resolved: ice: prevent tstamp ring allocation for non-PF VSI types The pf->txtime_txqs bitmap tracks which Tx queues have ETF (Earliest TxTime First) offload enabled. This bitmap is indexed by queue number and is set by ice_offload_txtime(), which only operates on PF VSI queues. However, ice_is_txtime_ena() does not check the VSI type before consulting the bitmap. When ETF offload is enabled on PF Tx queue 0, bit 0 is set in pf->txtime_txqs. During a subsequent PCI reset rebuild, the CTRL VSI's Tx queue 0 is reconfigured and ice_is_txtime_ena() is called for that ring. Since it only checks pf->txtime_txqs by queue index without distinguishing VSI type, it finds bit 0 set and returns true, matching the PF VSI's ETF queue, not the CTRL VSI's. This causes ice_vsi_cfg_txq() to spuriously allocate a tstamp_ring for the CTRL VSI ring. Since CTRL VSI rings have no associated netdev, ice_clean_tx_ring() takes an early return at the !netdev check before reaching ice_free_tx_tstamp_ring(), leaking the allocation. Each PCI reset leaks one 64-byte tstamp_ring. Fix this by restricting ice_is_txtime_ena() to return true only for PF VSI rings, since txtime_txqs is only meaningful for PF VSI queues.

In the Linux kernel, the following vulnerability has been resolved: drm/bridge: cdns-dsi: Replace deprecated UNIVERSAL_DEV_PM_OPS() The deprecated UNIVERSAL_DEV_PM_OPS() macro uses the provided callbacks for both runtime PM and system sleep. This causes the DSI clocks to be disabled twice: once during runtime suspend and again during system suspend, resulting in a WARN message from the clock framework when attempting to disable already-disabled clocks. [ 84.384540] clk:231:5 already disabled [ 84.388314] WARNING: CPU: 2 PID: 531 at /drivers/clk/clk.c:1181 clk_core_disable+0xa4/0xac ... [ 84.579183] Call trace: [ 84.581624] clk_core_disable+0xa4/0xac [ 84.585457] clk_disable+0x30/0x4c [ 84.588857] cdns_dsi_suspend+0x20/0x58 [cdns_dsi] [ 84.593651] pm_generic_suspend+0x2c/0x44 [ 84.597661] ti_sci_pd_suspend+0xbc/0x15c [ 84.601670] dpm_run_callback+0x8c/0x14c [ 84.605588] __device_suspend+0x1a0/0x56c [ 84.609594] dpm_suspend+0x17c/0x21c [ 84.613165] dpm_suspend_start+0xa0/0xa8 [ 84.617083] suspend_devices_and_enter+0x12c/0x634 [ 84.621872] pm_suspend+0x1fc/0x368 To address this issue, replace UNIVERSAL_DEV_PM_OPS() with RUNTIME_PM_OPS(). Bridge and panel drivers should only deal with runtime PM, as the DRM framework manages system-wide power transitions through the bridge enable() and disable() hooks.

In the Linux kernel, the following vulnerability has been resolved: media: i2c: alvium: fix critical pointer access in alvium_ctrl_init The current implementation of alvium_ctrl_init creates several controls in function alvium_ctrl_init and uses the returned pointer without check. That can cause write access over NULL-pointer for several controls. The reworked code checks the pointers before adding flags.

In the Linux kernel, the following vulnerability has been resolved: media: rtl2832_sdr: Return queued buffers on start_streaming() failure The vb2 framework hands buffers to the driver via buf_queue() before calling start_streaming(). If start_streaming() returns an error without first returning those buffers via vb2_buffer_done(), vb2_start_streaming() fires WARN_ON(owned_by_drv_count) and the queued buffers leak. rtl2832_sdr_start_streaming() had multiple error paths that hit this trap: two direct early returns (-ENODEV, -ERESTARTSYS), plus six `goto err` paths covering subdev s_power, tuner setup, ADC setup, stream-buffer allocation, urb allocation, and urb submission failures. None of them returned the queued buffers. The original function had no distinct success exit and fell straight through into the err label, which previously only did mutex_unlock and "return ret". Adding queued-buffer cleanup at err must therefore be paired with an explicit success return; otherwise every successful start would also drain the buffer queue and kill streaming. Add that success return, then add rtl2832_sdr_cleanup_queued_bufs() at the err label and before each early return. The cleanup helper takes a vb2_buffer_state argument so that the start_streaming error paths can pass VB2_BUF_STATE_QUEUED (as expected by userspace on start_streaming failure) while stop_streaming keeps its existing VB2_BUF_STATE_ERROR semantics. This mirrors the uvcvideo fix in commit 4cf3b6fd54eb ("media: uvcvideo: Return queued buffers on start_streaming() failure"). The err label still does not roll back power_ctrl(), frontend_ctrl(), the POWER_ON flag, or stream/URB allocations that may have happened before the failing step. Those are pre-existing leaks of a different class and are not addressed here.

In the Linux kernel, the following vulnerability has been resolved: media: vivid: fix cleanup bugs in vivid_init() When platform_device_register() fails in vivid_init(), the embedded struct device in vivid_pdev has already been initialized by device_initialize(), but the failure path jumps to free_output_strings without dropping the device reference for the current platform device: vivid_init() -> platform_device_register(&vivid_pdev) -> device_initialize(&vivid_pdev.dev) -> setup_pdev_dma_masks(&vivid_pdev) -> platform_device_add(&vivid_pdev) This leads to a reference leak when platform_device_register() fails. Fix this by calling platform_device_put() before jumping to the common cleanup path. Also, the unreg_driver label incorrectly calls platform_driver_register() instead of platform_driver_unregister(), which breaks cleanup when workqueue creation fails after successful driver registration. Fix that as well. The reference leak was identified by a static analysis tool I developed and confirmed by manual review. The incorrect cleanup call was found during code inspection.