CVE Feed

In the Linux kernel, the following vulnerability has been resolved: ASoC: tas2562: Validate values for volume writes tas2562_volume_control_put() does not do any validation of the control value written by userspace, it uses it to look up a value in a fixed size array which can easily be overflowed and then writes whatever value it gets back to the device. Add validation that we are loading a value we have in the array.

In the Linux kernel, the following vulnerability has been resolved: ipvs: revalidate ihl to prevent out-of-bounds access While the outer IP header is already pulled into the skb head, we must be careful and revalidate the embedded headers after reading them from the skb frags to prevent out-of-bounds access. One such place reported by Sashiko is ip_vs_nat_icmp() where local process can change the ihl field and after skb_ensure_writable() we can see larger value which is a problem for the ip_send_check(cih) calls. Add check to drop the packet if the ihl field is changed.

In the Linux kernel, the following vulnerability has been resolved: net/sched: cls_u32: skip hash tables in u32_bind_class() u32_walk() enumerates both struct tc_u_hnode and struct tc_u_knode through the walker callback. u32_bind_class() unconditionally casts the passed fh to tc_u_knode and accesses &n->res, so when fh is actually a tc_u_hnode, which has no tcf_result member, this results in a slab-out-of-bounds read of res->classid in tc_cls_bind_class(). The issue can be reproduced with the following commands: tc qdisc add dev lo root handle 1: hfsc tc class add dev lo parent 1: classid 1:1 hfsc sc rate 1000kbit tc filter add dev lo parent 1:1 protocol ip prio 1 u32 match u32 0 0 flowid 1:1 tc class add dev lo parent 1: classid 1:2 hfsc sc rate 2000kbit Fix this by skipping hash tables via the TC_U32_KEY(handle) check.

In the Linux kernel, the following vulnerability has been resolved: l2tp: fix tunnel and session refcount leak on seq_file release In pppol2tp_proc_open() and l2tp_dfs_seq_open(), iteration state (pd->tunnel and pd->session) is kept in seq_file private data to allow iteration across multiple read() system calls. However, if userspace closes /proc/net/pppol2tp or /sys/kernel/debug/l2tp/tunnels before reading to end-of-file (EOF), any tunnel or session reference stored in pd->tunnel / pd->session is left un-dropped when seq_file private data is freed. Fix this by dropping any remaining pd->tunnel and pd->session references in pppol2tp_proc_release() and l2tp_dfs_seq_release() when closing the file.

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: ipc4-pcm: Continue the pipeline trigger in case of IPC timeout Ignore IPC errors for pipeline state change if the firmware state is crashed or the IPC has timed out. If the firmware has crashed the kernel still needs to go through the state changes to reset its internal to be able to correctly work the next time the DSP is booted up. The case with IPC timeout is a bit more problematic, but it has been rootcaused to be the result of system scheduling blockage and the firmware did actually received and handled the message, but the reply handling got blocked by issues outside of the SOF stack. So far the best way to handle this is to continue with setting the state.

In the Linux kernel, the following vulnerability has been resolved: mptcp: reclaim forward-allocated memory on RX path errors After commit 9db5b3cec4ec ("mptcp: borrow forward memory from subflow"), errors in the receive path prior to queueing skbs into the receive queue do not trigger forward-allocated memory reclaiming. Prevent forward memory from growing unboundedly in pathological drop scenarios by explicitly reclaiming memory when skbs are dropped.

In the Linux kernel, the following vulnerability has been resolved: s390/qeth: validate user buffer length in SNMP and ARP query ioctls qeth_snmp_command() and qeth_l3_arp_query() allocate a buffer sized by a user-supplied length (udata_len) without checking a lower bound, then set udata_offset to a fixed non-zero value and pass both to a reply callback. The callback bounds-checks the copy with if ((udata_len - udata_offset) < len) Both fields are u32, so a udata_len smaller than udata_offset makes the subtraction wrap and the check pass, and the following memcpy() writes past the allocation. A udata_len of 0 also yields ZERO_SIZE_PTR from kzalloc(), which the existing NULL check does not catch. Reject buffers smaller than udata_offset before allocating, so the callback subtraction can no longer underflow.

In the Linux kernel, the following vulnerability has been resolved: fbdev: clear fb_info->mode before deleting a videomode fb_set_var() can delete a mode from info->modelist when userspace passes FB_ACTIVATE_INV_MODE through FBIOPUT_VSCREENINFO. The code checks that the mode being deleted is not the current info->var and that fbcon is not using it, but it does not check fb_info->mode. fb_info->mode may still point into the modelist entry being deleted. If the entry is freed, later mode sysfs reads through show_mode() can dereference a stale pointer. Clear fb_info->mode before calling fb_delete_videomode() when it matches the mode being removed.

In the Linux kernel, the following vulnerability has been resolved: libceph: Avoid using invalid osd indices from primary_temp A corrupted osdmap received from a Ceph monitor or OSD may contain osd indices in its pg_temp, primary_temp, pg_upmap, and pg_upmap_items parts that don't exist, i.e., that are greater than max_osd or smaller than CEPH_HOMELESS_OSD (-1). These indices are used to create the up and acting set in ceph_pg_to_up_acting_osds(), called from calc_target(). While most of these osd indices are checked, the one from primary_temp is not. Subsequently, this may lead to calc_target() returning this (potentially invalid) index as target osd for a (linger) request. Because the osd_state, osd_weight, and osd_addr arrays only contain max_osd entries (with indices 0 to max_osd -1), this leads to out-of-bounds accesses when trying to read values from these arrays. This patch fixes the issue by adding a check to get_temp_osds(), so that only valid osd indices from primary_temp are used, and it falls back to using the primary from pg_temp or the up set if it is invalid. [ idryomov: changelog ]

In the Linux kernel, the following vulnerability has been resolved: s390/vfio_ccw: Cancel existing workqueues The initialization of the io_work and crw_work workqueues begs the question of whether they should be un-initialized. Add the corresponding cleanup tags in _release_dev to ensure work isn't dispatched after the private struct is free'd.

In the Linux kernel, the following vulnerability has been resolved: s390/vfio_ccw: Fix out of bounds check on CCW array The routine ccwchain_calc_length() counts the number of channel command words (CCWs) that are chained together in a single channel program, and rejects anything larger than CCWCHAIN_LEN_MAX (256) CCWs. The loop itself is "do..while (count < 257)", and while the logic in is_cpa_within_range() correctly adjusts between the 0-index array of CCWs and the count of CCWs starting at 1, this means it would look at a possible 257th CCW before ending the loop and (correctly) returning an error. Fix this by restructuring the loop to break as soon as 256 CCWs (thus indexes 0-255) are examined, without looking at memory outside the range.

In the Linux kernel, the following vulnerability has been resolved: s390/vfio_ccw: Move cp cleanup out of not operational The fsm_notoper() routine is called when the device has been lost, and is (by definition) no longer operational. Since this can happen asynchronously from the normal behavior of the driver, the cleanup may happen when holding other locks in the calling sequence (notably, the cio subchannel lock). Push the cleanup of the private->cp resources to a workqueue, where it can be done out from under that lock sequence and a future patch can safely manage the locking requirements.

In the Linux kernel, the following vulnerability has been resolved: s390/vfio_ccw: Selectively expand io_mutex The io_mutex was defined to serialize the io_regions, but then has also sort of been associated with the I/O themselves because of the close relationship they share. With the handful of races that are possible, the choices are either to: A) expand the scope of io_mutex to close these remaining windows, or B) reduce the scope of io_mutex to just io_region, and introduce a new lock mechanism for the remaining I/O resources This patch implements A, since B brings with it a lot more interactions that would need to be tracked and kept in a correct hierarchy. It also takes advantage of the workqueue element for cp_free() that now gets called out of fsm_notoper(), which could be invoked out of an interrupt context and thus cannot acquire a mutex itself.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: validate GEM_CREATE domain combinations AMDGPU_GEM_CREATE checked domain bits against AMDGPU_GEM_DOMAIN_MASK, but did not validate domain combinations. Userspace could combine CPU|GTT|VRAM with DOORBELL, GDS, GWS, or OA, making amdgpu_bo_placement_from_domain() exceed AMDGPU_BO_MAX_PLACEMENTS and hit BUG_ON(). Allow combinations only within CPU/GTT/VRAM, and require non-CPU/GTT/ VRAM domains to be specified one at a time. Return -EINVAL for invalid combinations in amdgpu_gem_create_ioctl(). v2: Rename helper from amdgpu_gem_domain_valid() to amdgpu_gem_are_domains_valid() (Christian) (cherry picked from commit db39852d0c39843cb02048dfb47e4b8c703e9080)

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix UVD decode image min size calculation This needs to use pitch instead of width. Also reject pitch over 4096 to avoid overflow. (cherry picked from commit b41c8cb12e202b220353332ab87dc01a11f69304)

In the Linux kernel, the following vulnerability has been resolved: xfs: bounds-check buffer log item's dirty bitmap xlog_recover_do_reg_buffer() replays each dirty region described by a buffer log item's bitmap into the buffer read for that item: memcpy(xfs_buf_offset(bp, (uint)bit << XFS_BLF_SHIFT), item->ri_buf[i].iov_base, nbits << XFS_BLF_SHIFT); The destination offset (bit/nbits, from the logged dirty bitmap) and the buffer size (from the logged blf_len) are both attacker-controlled and otherwise unrelated, yet the only thing bounding the copy is an ASSERT(), which compiles away on production kernels. A crafted image logging a small blf_len together with a bitmap bit past the end of that buffer drives the memcpy() past the buffer's allocation, corrupting adjacent kernel heap during mount-time log recovery. This is reachable by anyone who can get a crafted image mounted -- the malicious-filesystem threat model XFS already guards against elsewhere. Turn the ASSERT() into a real XFS_IS_CORRUPT() check that aborts recovery of the buffer with -EFSCORRUPTED, consistent with the validate-and-fail idiom already used in xlog_recover_do_inode_buffer() and xfs_dquot_item_recover.c. xlog_recover_do_reg_buffer() therefore becomes STATIC int and its three callers propagate the error. Found and confirmed with KASAN on a CONFIG_XFS_DEBUG=n build: the crafted image trips a slab-out-of-bounds write before this change and fails recovery cleanly with -EFSCORRUPTED after it.

In the Linux kernel, the following vulnerability has been resolved: ceph: fix hanging __ceph_get_caps() with stale mds_wanted A reader can hang forever in __ceph_get_caps() when the client no longer holds `FILE_RD`, but local cap state still says that the capability is already wanted (via `mds_wanted`). One way to trigger this is through MDS cap revocation. If another client performs a conflicting operation, the MDS can revoke `FILE_RD` from the reader; the next read then has to reacquire `FILE_RD`. If the cap update that should request `FILE_RD` never reaches the MDS after `cap->mds_wanted` was raised, the reader is left holding only non-file caps while local `mds_wanted` still includes the file read caps. In that state, try_get_cap_refs() sees `need <= mds_wanted` and returns 0, so __ceph_get_caps() just waits on `i_cap_wq`. If the cap update that was supposed to request `FILE_RD never reaches the MDS after `cap->mds_wanted was` raised, no further request is sent and the waiter can sleep indefinitely until unrelated cap traffic happens to wake it up. The ordering issue is that `cap->mds_wanted` is updated in __prep_cap() before the `CEPH_MSG_CLIENT_CAPS message` is actually queued for send. That makes one field serve two different meanings at once: what this client wants, and what the client believes the MDS already knows it wants. A proper fix would be to split those states and track whether a cap update is actually in flight or has been observed by the MDS. However, simply moving the `cap->mds_wanted assignment` later would not be sufficient: queueing the message in the messenger does not guarantee that the MDS processed that specific wanted set, and reconnect or message loss can still invalidate that assumption. Fixing that properly would require a larger rework of the cap state machine. To allow simpler backports to stable kernels, this patch implements a simpler workaround: - stop waiting forever in __ceph_get_caps(); after a bounded wait, fall back to the renew path - make ceph_renew_caps() issue a synchronous `OPEN` request whenever the inode still does not actually hold the wanted caps, instead of only calling ceph_check_caps() The extra issued-vs-wanted check in ceph_renew_caps() is necessary because the previous test only checked whether the inode still had any real caps at all. That is not enough after revocation: the client can still hold something like `pLs` and yet be missing `FILE_RD` completely. In that case, falling back to ceph_check_caps() is not sufficient, because it still trusts `cap->mds_wanted` and may resend nothing. By requiring `(issued & wanted) == wanted` before taking the asynchronous path, the code only uses ceph_check_caps() when the `wanted caps` are already actually issued. Otherwise, it sends the synchronous `OPEN` renew. This preserves the existing asynchronous fast path when the wanted caps are already issued, avoids changing cap-state semantics, and fixes the hang by guaranteeing that a stalled waiter eventually retries through a path that does not rely on the stale `mds_wanted` state. [ idryomov: move CEPH_GET_CAPS_WAIT_TIMEOUT from libceph.h to mds_client.h, formatting ]

In the Linux kernel, the following vulnerability has been resolved: ipvlan: inherit needed_headroom and needed_tailroom from phy_dev ipvlan devices inherit hard_header_len from phy_dev during ipvlan_init(), but leave needed_headroom and needed_tailroom set to 0. When the underlying phy_dev (or stacked lower device) requires extra headroom or tailroom for headers/trailers (e.g. macsec, ipsec, wireguard, tunnels, or veth with rx headroom), upper layers calculating packet headroom and tailroom fail to reserve sufficient space. This can result in reallocation overhead, skb headroom underflows, or KASAN slab-use-after-free crashes when dev_hard_header() / ipvlan_hard_header() prepends header data or when lower devices append tailroom. Fix this by: 1. Inheriting needed_headroom and needed_tailroom from phy_dev in ipvlan_init(). 2. Propagating needed_headroom and needed_tailroom updates to attached ipvlans in ipvlan_device_event() when receiving NETDEV_FEAT_CHANGE events.

In the Linux kernel, the following vulnerability has been resolved: net/sched: cls_bpf: reject dev-bound programs bound to a different device cls_bpf_prog_from_efd() obtained a SCHED_CLS program via bpf_prog_get_type_dev() but never verified that a device-bound (offloaded) program's bound netdev matches the TC netdev the classifier is being attached to. This let a program loaded with prog_ifindex for device A be attached via cls_bpf + skip_sw to device B; deleting device A then destroyed the program's offload state while it was still attached to device B, triggering a netdevsim WARN (panic with panic_on_warn=1). Mirror the XDP attach path (net/core/dev.c) and reject the attach with -EINVAL when a dev-bound program's bound device does not match the target device.

In the Linux kernel, the following vulnerability has been resolved: ovpn: defer key slot crypto freeing to workqueue Key slots are released through a kref and the existing release path frees the AEAD transforms from an RCU callback. That is not safe for all crypto implementations: crypto_free_aead can sleep, for example when an async or hardware implementation has teardown work to complete. Use queue_rcu_work for key-slot release. This keeps the RCU grace period needed by lockless key-slot readers, but runs the actual crypto teardown from workqueue context where sleeping is allowed. Once the rcu_work callback runs, pre-existing RCU readers are gone, and the final kref put already proves that no transform user remains, so the worker can release the AEAD transforms and free the slot directly. The previous patch drains ovpn_wq during module exit, so queued key-slot teardown work cannot outlive module text.

In the Linux kernel, the following vulnerability has been resolved: xfs: fix exchange-range reflink flag clearing issue with INO1_WRITTEN When exchanging two full-file ranges, xmi_can_exchange_reflink_flags() can move the reflink inode flag from the file that currently has it to the other file, as long as exactly one side is marked. This assumes that the file contents, and therefore all shared extents, are exchanged. That assumption is not true when XFS_EXCHMAPS_INO1_WRITTEN is set. xfs_exchmaps_can_skip_mapping() can skip hole and unwritten mappings from file1, so an exchange can complete without moving every mapping that the earlier flag-swap decision accounted for. In that case the post-operation cleanup can clear the reflink flag from an inode that still owns shared written extents. Later writes then take the non-reflink write path and may update blocks that should still have been protected by CoW, which shows up as data corruption between reflink-related files. Fix this by disabling the reflink flag exchange whenever XFS_EXCHMAPS_INO1_WRITTEN is requested. The contents exchange can still proceed; the conservative outcome is that both inodes keep the reflink flag. The regular reflink flag cleanup path can drop the extra flag later once the inode no longer has shared extents.

stomper 5e2741e is vulnerable to Denial of Service. A malicious client can send partial STOMP frames and keep the TCP connections open, which, combined with the broker s use of edge-triggered epoll (EPOLLET) and MSG_PEEK in recv(), causes sockets to enter a permanent half-read state. When enough such connections accumulate, the broker stops receiving any further epoll events for those sockets and eventually hangs in epoll_wait, effectively refusing to process new messages.

AntFlow V2.0.0 is vulnerable to Incorrect Access Control. JiMuMDCCommonsRequestLoggingFilter.java retrieves the userid from the request header as the core of the identity verification mechanism, allowing attackers to forge any user identity credential information, thereby causing sensitive information leakage.

JeecgBoot v3.9.2 is vulnerable to Remote command execution. The CodeNode component of the AI Flow module supports Groovy script execution. While the `SecurityCheck` class employs a blacklist mechanism to intercept dangerous calls, the dynamic nature of Groovy allows this blacklist to be completely bypassed through string concatenation and reflection.

A Broken Access Control vulnerability exists in ThingsBoard Professional Edition (PE) 4.21 and below, within the Alarms comments functionality. An authenticated customer user can manipulate the respective API request parameters to create or modify system-generated alarm comments. This allows unauthorized impersonation of system messages and modification of trusted system-owned data, resulting in vertical privilege escalation and potential integrity violations.

An issue was discovered in Denx U-Boot before 2026.04. An integer overflow vulnerability exists in function ext4fs_get_bgdtable, the size calculation can lead to under allocation and this underallocated buffer will be used in memcpy() which could lead to arbitrary code execution, a denial of service, or other unspecified impacts.

Bird Home Automation GmbH D1101V-F 000140 is vulnerable to Incorrect Access Control via the Key derivation process, password validation process.

In AntFlow V2.0.0, ActivitiTest.java enables users to execute JUEL expressions without filtering the user input, which leads to a command execution vulnerability.

DocSys V2.02.80 is vulnerable to Any File Download. An attacker does not need to go through authentication to utilize the downloadDocEx.do interface and download any file via the parameter targetPath.

An issue in Comfast CF-WR630AX v.2.7.0.2 allows a remote attacker to execute arbitrary code via the /usr/bin/webmgnt, /cgi-bin/mbox-config, and the parameters timestr, display_n.

Stomper 5e2741e is vulnerable to Use-After-Free. When a single client repeatedly issues SUBSCRIBE commands for the same destination over one connection and then closes that connection, the broker performs incorrect cleanup of its internal subscription structures. This results in a heap use-after-free during StompClient destruction, causing the broker process to crash. An unauthenticated client can exploit this to reliably trigger a denial of service.

In the Linux kernel, the following vulnerability has been resolved: s390/vfio_ccw: Implement a crw lock Unlike the channel_program struct, which covers synchronous I/O submissions and asynchronous interrupts, the CRW region relies exclusively on asynchronous events coming from hardware. Implement a lock to manage the list of those payloads, to ensure they are read cohesively.

In the Linux kernel, the following vulnerability has been resolved: ovpn: finish crypto callback cleanup before peer release Crypto completion callbacks hold both key-slot and peer references. The peer reference pins the netdev, and dropping the last peer reference can let netdev unregistration and module removal make progress. Do not release that peer reference before the callback has finished its own cleanup. If ovpn_crypto_key_slot_put runs after ovpn_peer_put, it can schedule an RCU callback backed by module text after ovpn_cleanup rcu_barrier has already run. The TX error path also freed the remaining skb after ovpn_peer_put, leaving callback cleanup outside the peer/netdev lifetime window. Release the key slot and free any remaining skb first, then drop the peer reference as the last callback action.

An issue in TokTok qTox v1.18.4 allows a local attacker to cause a denial of service via the src/persistence/serialize.cpp component

In the Linux kernel, the following vulnerability has been resolved: drm/shmem_helper: Check VMA boundaries for PMD mappings In the ->huge_fault handler do not install a PMD huge page mapping if the huge page exceeds the boundaries of the VMA. All other ->huge_fault handlers have similar checks and the resulting mapping will trigger a VM_BUG_ON_VMA() if it ever reaches copy_pmd_range().

In the Linux kernel, the following vulnerability has been resolved: Input: synaptics-rmi4 - zero report size on F54 work error In rmi_f54_work(), if an error occurs during report request or command verification, the code jumped directly to the 'error' label, bypassing the 'abort' label where f54->report_size was normally zeroed out. This left f54->report_size containing its previous successful payload size. If a user then altered the V4L2 format to a smaller size, and a subsequent run failed, rmi_f54_buffer_queue() would copy the stale, larger payload size into the shrunken V4L2 buffer, causing a heap buffer overflow. Fix this by merging the 'abort' and 'error' labels into a single 'out' exit path, and ensuring that f54->report_size is always set to 0 on failure by checking for error and zeroing the local report_size first.

In the Linux kernel, the following vulnerability has been resolved: Input: synaptics-rmi4 - propagate F54 worker errors to V4L2 queue Previously, rmi_f54_buffer_queue() waited for the worker thread to finish but ignored whether it succeeded. If the worker failed (e.g., due to a timeout or register read failure), the queue thread would silently return success, delivering stale or uninitialized memory to userspace. Add a 'report_error' field to struct f54_data to store the worker's exit status. Check this field in rmi_f54_buffer_queue() after the worker finishes, and mark the buffer as VB2_BUF_STATE_ERROR if an error occurred.

In the Linux kernel, the following vulnerability has been resolved: Input: hynitron_cstxxx - validate touch count and finger IDs The driver allocates max_touch_num input slots, which are indexed from zero through max_touch_num - 1. The current check allows a finger ID equal to max_touch_num to reach cst3xx_report_contact(). While the input core ignores out-of-range slot indices, reporting touch data without a valid slot change corrupts the touch state of the previously active slot. The touch count is read from the controller's report and is used to index the fixed-size report buffer without first checking its range. Reject counts larger than the supported number of touch slots before checking the trailing byte or parsing touch data. Reject finger IDs equal to or greater than max_touch_num, and return immediately when an invalid finger ID is encountered so that corrupt touch frames are discarded instead of reporting partial contact state. The V821 Avaota F1 board configures the vendor driver with one touch slot, so finger ID 1 is already invalid on that device.

The device metadata import interface /device/instance/{productId}/property-metadata/import of jetlinks community 2.11 is vulnerable to Server-side request forgery (SSRF).

In the Linux kernel, the following vulnerability has been resolved: openrisc: signal: do not restore privileged SR bits on sigreturn restore_sigcontext() copies the whole supervision register (SR) from the signal frame and only clears SPR_SR_SM before the value is reloaded into the hardware SR (through ESR and l.rfe) on the return to user space. All other SR bits are left under user control. An unprivileged task can thus return from a signal handler through a crafted sigframe that clears SPR_SR_DME. With the data MMU disabled the CPU performs no translation or protection on data accesses, so the task gains read and write access to arbitrary physical memory, a local privilege escalation. SPR_SR_IME, SPR_SR_SUMRA, SPR_SR_LEE, SPR_SR_EPH and the cache-enable bits are exposed the same way. The ptrace GPR regset already refuses any change to SR for exactly this reason. Restore only the arithmetic flag bits (F, CY, OV) from the signal frame and take every privileged control bit from the SR the kernel saved on signal entry. Verified with qemu-system-or1k -M or1k-sim: before this change an unprivileged PoC clears SPR_SR_DME in rt_sigreturn and writes a marker to physical address 0x03000000 (beyond the kernel's mem=32M); afterwards the same PoC receives SIGSEGV and physical memory is unchanged.

In the Linux kernel, the following vulnerability has been resolved: scsi: core: pair EH runtime PM get and put shost->eh_noresume is currently consulted twice in one error handling iteration: once before scsi_autopm_get_host() and once again before scsi_autopm_put_host(). That is racy when a PM-triggered error path flips shost->eh_noresume while the SCSI EH thread is still running. The problem flow looks like this: PM path ufshcd_set_dev_pwr_mode() shost->eh_noresume = 1 ufshcd_execute_start_stop <-- trigger EH ... shost->eh_noresume = 0 EH path scsi_error_handler() if (!shost->eh_noresume) scsi_autopm_get_host() <-- skipped ... if (!shost->eh_noresume) scsi_autopm_put_host() <-- executed later In that case one EH iteration can skip autoresume on entry and still drop a runtime PM reference on exit. That leaves an unmatched runtime PM put and can trigger a runtime PM usage count underflow. Fix this by making eh_noresume a regular bool so it can be accessed with READ_ONCE() and WRITE_ONCE(). Snapshot it once per EH iteration and use that snapshot for both runtime PM get and put decisions.

In the Linux kernel, the following vulnerability has been resolved: perf: Reject exited events as group leaders perf_event_remove_on_exec() sets remove-on-exec events to the EXIT state and detaches their group relationships. The event's file descriptor can remain open, however, and perf_event_open() currently accepts that event as a group leader because its early validation rejects only REVOKED and DEAD events. A new sibling can consequently be linked to the detached leader. When the leader is closed, perf_group_detach() observes that its PERF_ATTACH_GROUP bit is already clear and skips the new sibling. The sibling then retains a group_leader pointer to the freed event. Reject group leaders in the EXIT state. Perform the check while holding the shared context mutex so that an exec in the target task cannot detach the leader between validation and group attachment. [peterz: make the earlier test fully consistent]

In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: fix refcount race between list:set GC and swap __ip_set_put_byindex() resolved the index to a set pointer under RCU, then took ip_set_ref_lock in __ip_set_put() to decrement set->ref. ip_set_swap() holds that same lock while swapping both the ip_set_list slots and the two sets' ref counters, so it can interleave between the dereference and the lock acquisition, leaving the caller to decrement a set whose reference already moved to the other index and hit BUG_ON(set->ref == 0). list_set_gc() reaches this from timer softirq, which the nfnl mutex does not serialize against swap: an expiring list:set member calls list_set_del() -> ip_set_put_byindex() while IPSET_CMD_SWAP runs on the referenced sets. Resolve the index and decrement under ip_set_ref_lock, as ip_set_swap() already does, keeping the refcount tied to the index rather than to a stale set pointer. kernel BUG at net/netfilter/ipset/ip_set_core.c:685! Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI RIP: 0010:ip_set_put_byindex (net/netfilter/ipset/ip_set_core.c:870) Call Trace: <IRQ> list_set_del (net/netfilter/ipset/ip_set_list_set.c:159) set_cleanup_entries (net/netfilter/ipset/ip_set_list_set.c:181) list_set_gc (net/netfilter/ipset/ip_set_list_set.c:578) call_timer_fn (kernel/time/timer.c:1748) __run_timers (kernel/time/timer.c:1799 kernel/time/timer.c:2374) run_timer_softirq (kernel/time/timer.c:2405) </IRQ> Kernel panic - not syncing: Fatal exception in interrupt

Stomper 5e2741e is vulnerable to Use-After-Free. When a client sends multiple CONNECT frames on the same TCP connection, and subsequently another client (or a later connection) sends SEND frames to a destination previously subscribed on that connection, the broker may dereference a pointer to a StompStreamSocket object that has already been freed. This results in a heap use-after-free and process crash. Because the protocol does not authenticate or restrict such sequences by default.

An issue was discovered in openRISC OR1200 commit 83ac6b. An inaccurate update of program counter (PC) values when SPR changes can lead to a Denial of Service (DoS).

In the Linux kernel, the following vulnerability has been resolved: gpio: ml-ioh: use raw_spinlock_t for the register lock ioh_irq_type() is registered as the irq_chip .irq_set_type callback and takes chip->spinlock with spin_lock_irqsave(). This callback is reached from __setup_irq() -> __irq_set_trigger() -> chip->irq_set_type() while the caller holds desc->lock, a raw_spinlock_t, with hardirqs disabled. That context is not sleepable, but on PREEMPT_RT a regular spinlock_t is an rtmutex-backed sleeping lock, so acquiring it there is invalid. ioh_irq_enable() and ioh_irq_disable() take the same lock from the .irq_enable/.irq_disable callbacks, which are likewise invoked with desc->lock held. Convert the register lock to raw_spinlock_t. The same lock also serializes the GPIO direction/value callbacks and the suspend/resume register save/restore, and those critical sections only perform short sequences of MMIO register accesses (ioread32()/iowrite32()); the .irq_set_type callback additionally emits a dev_warn() on an unsupported type. None of these are sleepable operations, so keeping this register lock non-sleeping is appropriate for the irqchip callbacks and does not change the GPIO-side locking contract. This is the same fix as commit a02b8950d619 ("gpio: pch: use raw_spinlock_t for the register lock"); this driver shares the same structure as gpio-pch.

In the Linux kernel, the following vulnerability has been resolved: Input: sur40 - fix input device registration ordering In sur40_probe(), input_register_device() was previously called early before the V4L2 video device and vb2_queue components were fully initialized. If userspace opened the input device immediately upon registration, sur40_open() would trigger and start the sur40_poll() worker thread. This worker thread invokes sur40_process_video() and accesses the uninitialized vb2_queue structure, leading to a data race and potential system crash. Furthermore, if V4L2 or video registration failed after input_register_device() succeeded, the error path fell through to calling input_free_device() on a successfully registered device instead of input_unregister_device(), corrupting input core state. Move input_register_device() to the very end of sur40_probe(). This ensures the V4L2 and video queue structures are fully initialized before polling can start, and naturally resolves the error path bug since input_free_device() is now only called when input registration has not yet occurred. To maintain strict LIFO (Last-In, First-Out) teardown ordering, also move input_unregister_device() to the very beginning of sur40_disconnect(). This guarantees that the input polling worker thread is stopped before V4L2 video components or control handlers are unregistered.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix NULL pointer dereference in amdgpu_dm_crtc_set_vblank() amdgpu_dm_crtc_set_vblank() dereferences acrtc_state->stream when vblank is enabled/queried from DRM_IOCTL_MODE_CRTC_GET_SEQUENCE before a stream is attached to it. BUG: kernel NULL pointer dereference, address: 0000000000000008 RIP: amdgpu_dm_crtc_set_vblank+0x6b/0x4d0 [amdgpu] Call Trace: drm_vblank_enable drm_vblank_get drm_crtc_get_sequence_ioctl drm_ioctl_kernel drm_ioctl Reproduced by running VKCTS with WSI tests enabled on RADV. Guard the enable path on acrtc_state->stream being non-NULL, matching the existing checks in this function. (cherry picked from commit 7b1b31bf6942e6f43509b48da23f8e27269aac39)

DWSurvey v6.14.0 is is vulnerable to authentication bypass via the '/api/dwsurvey/none/' and '/api/dwsurvey/up/**' parameters.

In DocSys-master V2.02.85, the downloadDocEx interface in src/com/DocSystem/controller/DocController.java has an arbitrary file read vulnerability: