CVE Feed

In the Linux kernel, the following vulnerability has been resolved: xfrm: always flush state and policy upon NETDEV_UNREGISTER event syzbot is reporting that "struct xfrm_state" refcount is leaking. unregister_netdevice: waiting for netdevsim0 to become free. Usage count = 2 ref_tracker: netdev@ffff888052f24618 has 1/1 users at __netdev_tracker_alloc include/linux/netdevice.h:4400 [inline] netdev_tracker_alloc include/linux/netdevice.h:4412 [inline] xfrm_dev_state_add+0x3a5/0x1080 net/xfrm/xfrm_device.c:316 xfrm_state_construct net/xfrm/xfrm_user.c:986 [inline] xfrm_add_sa+0x34ff/0x5fa0 net/xfrm/xfrm_user.c:1022 xfrm_user_rcv_msg+0x58e/0xc00 net/xfrm/xfrm_user.c:3507 netlink_rcv_skb+0x158/0x420 net/netlink/af_netlink.c:2550 xfrm_netlink_rcv+0x71/0x90 net/xfrm/xfrm_user.c:3529 netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline] netlink_unicast+0x5aa/0x870 net/netlink/af_netlink.c:1344 netlink_sendmsg+0x8c8/0xdd0 net/netlink/af_netlink.c:1894 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg net/socket.c:742 [inline] ____sys_sendmsg+0xa5d/0xc30 net/socket.c:2592 ___sys_sendmsg+0x134/0x1d0 net/socket.c:2646 __sys_sendmsg+0x16d/0x220 net/socket.c:2678 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xcd/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f This is because commit d77e38e612a0 ("xfrm: Add an IPsec hardware offloading API") implemented xfrm_dev_unregister() as no-op despite xfrm_dev_state_add() from xfrm_state_construct() acquires a reference to "struct net_device". I guess that that commit expected that NETDEV_DOWN event is fired before NETDEV_UNREGISTER event fires, and also assumed that xfrm_dev_state_add() is called only if (dev->features & NETIF_F_HW_ESP) != 0. Sabrina Dubroca identified steps to reproduce the same symptoms as below. echo 0 > /sys/bus/netdevsim/new_device dev=$(ls -1 /sys/bus/netdevsim/devices/netdevsim0/net/) ip xfrm state add src 192.168.13.1 dst 192.168.13.2 proto esp \ spi 0x1000 mode tunnel aead 'rfc4106(gcm(aes))' $key 128 \ offload crypto dev $dev dir out ethtool -K $dev esp-hw-offload off echo 0 > /sys/bus/netdevsim/del_device Like these steps indicate, the NETIF_F_HW_ESP bit can be cleared after xfrm_dev_state_add() acquired a reference to "struct net_device". Also, xfrm_dev_state_add() does not check for the NETIF_F_HW_ESP bit when acquiring a reference to "struct net_device". Commit 03891f820c21 ("xfrm: handle NETDEV_UNREGISTER for xfrm device") re-introduced the NETDEV_UNREGISTER event to xfrm_dev_event(), but that commit for unknown reason chose to share xfrm_dev_down() between the NETDEV_DOWN event and the NETDEV_UNREGISTER event. I guess that that commit missed the behavior in the previous paragraph. Therefore, we need to re-introduce xfrm_dev_unregister() in order to release the reference to "struct net_device" by unconditionally flushing state and policy.

In the Linux kernel, the following vulnerability has been resolved: fbdev: vt8500lcdfb: fix missing dma_free_coherent() fbi->fb.screen_buffer is allocated with dma_alloc_coherent() but is not freed if the error path is reached.

In the Linux kernel, the following vulnerability has been resolved: net: do not pass flow_id to set_rps_cpu() Blamed commit made the assumption that the RPS table for each receive queue would have the same size, and that it would not change. Compute flow_id in set_rps_cpu(), do not assume we can use the value computed by get_rps_cpu(). Otherwise we risk out-of-bound access and/or crashes.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conntrack_h323: fix OOB read in decode_choice() In decode_choice(), the boundary check before get_len() uses the variable `len`, which is still 0 from its initialization at the top of the function: unsigned int type, ext, len = 0; ... if (ext || (son->attr & OPEN)) { BYTE_ALIGN(bs); if (nf_h323_error_boundary(bs, len, 0)) /* len is 0 here */ return H323_ERROR_BOUND; len = get_len(bs); /* OOB read */ When the bitstream is exactly consumed (bs->cur == bs->end), the check nf_h323_error_boundary(bs, 0, 0) evaluates to (bs->cur + 0 > bs->end), which is false. The subsequent get_len() call then dereferences *bs->cur++, reading 1 byte past the end of the buffer. If that byte has bit 7 set, get_len() reads a second byte as well. This can be triggered remotely by sending a crafted Q.931 SETUP message with a User-User Information Element containing exactly 2 bytes of PER-encoded data ({0x08, 0x00}) to port 1720 through a firewall with the nf_conntrack_h323 helper active. The decoder fully consumes the PER buffer before reaching this code path, resulting in a 1-2 byte heap-buffer-overflow read confirmed by AddressSanitizer. Fix this by checking for 2 bytes (the maximum that get_len() may read) instead of the uninitialized `len`. This matches the pattern used at every other get_len() call site in the same file, where the caller checks for 2 bytes of available data before calling get_len().

In the Linux kernel, the following vulnerability has been resolved: ntb: ntb_hw_switchtec: Fix array-index-out-of-bounds access Number of MW LUTs depends on NTB configuration and can be set to MAX_MWS, This patch protects against invalid index out of bounds access to mw_sizes When invalid access print message to user that configuration is not valid.

In the Linux kernel, the following vulnerability has been resolved: kcm: fix zero-frag skb in frag_list on partial sendmsg error Syzkaller reported a warning in kcm_write_msgs() when processing a message with a zero-fragment skb in the frag_list. When kcm_sendmsg() fills MAX_SKB_FRAGS fragments in the current skb, it allocates a new skb (tskb) and links it into the frag_list before copying data. If the copy subsequently fails (e.g. -EFAULT from user memory), tskb remains in the frag_list with zero fragments: head skb (msg being assembled, NOT yet in sk_write_queue) +-----------+ | frags[17] | (MAX_SKB_FRAGS, all filled with data) | frag_list-+--> tskb +-----------+ +----------+ | frags[0] | (empty! copy failed before filling) +----------+ For SOCK_SEQPACKET with partial data already copied, the error path saves this message via partial_message for later completion. For SOCK_SEQPACKET, sock_write_iter() automatically sets MSG_EOR, so a subsequent zero-length write(fd, NULL, 0) completes the message and queues it to sk_write_queue. kcm_write_msgs() then walks the frag_list and hits: WARN_ON(!skb_shinfo(skb)->nr_frags) TCP has a similar pattern where skbs are enqueued before data copy and cleaned up on failure via tcp_remove_empty_skb(). KCM was missing the equivalent cleanup. Fix this by tracking the predecessor skb (frag_prev) when allocating a new frag_list entry. On error, if the tail skb has zero frags, use frag_prev to unlink and free it in O(1) without walking the singly-linked frag_list. frag_prev is safe to dereference because the entire message chain is only held locally (or in kcm->seq_skb) and is not added to sk_write_queue until MSG_EOR, so the send path cannot free it underneath us. Also change the WARN_ON to WARN_ON_ONCE to avoid flooding the log if the condition is somehow hit repeatedly. There are currently no KCM selftests in the kernel tree; a simple reproducer is available at [1]. [1] https://gist.github.com/mrpre/a94d431c757e8d6f168f4dd1a3749daa

In the Linux kernel, the following vulnerability has been resolved: 9p/xen: protect xen_9pfs_front_free against concurrent calls The xenwatch thread can race with other back-end change notifications and call xen_9pfs_front_free() twice, hitting the observed general protection fault due to a double-free. Guard the teardown path so only one caller can release the front-end state at a time, preventing the crash. This is a fix for the following double-free: [ 27.052347] Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC NOPTI [ 27.052357] CPU: 0 UID: 0 PID: 32 Comm: xenwatch Not tainted 6.18.0-02087-g51ab33fc0a8b-dirty #60 PREEMPT(none) [ 27.052363] RIP: e030:xen_9pfs_front_free+0x1d/0x150 [ 27.052368] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 41 55 41 54 55 48 89 fd 48 c7 c7 48 d0 92 85 53 e8 cb cb 05 00 48 8b 45 08 48 8b 55 00 <48> 3b 28 0f 85 f9 28 35 fe 48 3b 6a 08 0f 85 ef 28 35 fe 48 89 42 [ 27.052377] RSP: e02b:ffffc9004016fdd0 EFLAGS: 00010246 [ 27.052381] RAX: 6b6b6b6b6b6b6b6b RBX: ffff88800d66e400 RCX: 0000000000000000 [ 27.052385] RDX: 6b6b6b6b6b6b6b6b RSI: 0000000000000000 RDI: 0000000000000000 [ 27.052389] RBP: ffff88800a887040 R08: 0000000000000000 R09: 0000000000000000 [ 27.052393] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888009e46b68 [ 27.052397] R13: 0000000000000200 R14: 0000000000000000 R15: ffff88800a887040 [ 27.052404] FS: 0000000000000000(0000) GS:ffff88808ca57000(0000) knlGS:0000000000000000 [ 27.052408] CS: e030 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 27.052412] CR2: 00007f9714004360 CR3: 0000000004834000 CR4: 0000000000050660 [ 27.052418] Call Trace: [ 27.052420] <TASK> [ 27.052422] xen_9pfs_front_changed+0x5d5/0x720 [ 27.052426] ? xenbus_otherend_changed+0x72/0x140 [ 27.052430] ? __pfx_xenwatch_thread+0x10/0x10 [ 27.052434] xenwatch_thread+0x94/0x1c0 [ 27.052438] ? __pfx_autoremove_wake_function+0x10/0x10 [ 27.052442] kthread+0xf8/0x240 [ 27.052445] ? __pfx_kthread+0x10/0x10 [ 27.052449] ? __pfx_kthread+0x10/0x10 [ 27.052452] ret_from_fork+0x16b/0x1a0 [ 27.052456] ? __pfx_kthread+0x10/0x10 [ 27.052459] ret_from_fork_asm+0x1a/0x30 [ 27.052463] </TASK> [ 27.052465] Modules linked in: [ 27.052471] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: ovpn: tcp - fix packet extraction from stream When processing TCP stream data in ovpn_tcp_recv, we receive large cloned skbs from __strp_rcv that may contain multiple coalesced packets. The current implementation has two bugs: 1. Header offset overflow: Using pskb_pull with large offsets on coalesced skbs causes skb->data - skb->head to exceed the u16 storage of skb->network_header. This causes skb_reset_network_header to fail on the inner decapsulated packet, resulting in packet drops. 2. Unaligned protocol headers: Extracting packets from arbitrary positions within the coalesced TCP stream provides no alignment guarantees for the packet data causing performance penalties on architectures without efficient unaligned access. Additionally, openvpn's 2-byte length prefix on TCP packets causes the subsequent 4-byte opcode and packet ID fields to be inherently misaligned. Fix both issues by allocating a new skb for each openvpn packet and using skb_copy_bits to extract only the packet content into the new buffer, skipping the 2-byte length prefix. Also, check the length before invoking the function that performs the allocation to avoid creating an invalid skb. If the packet has to be forwarded to userspace the 2-byte prefix can be pushed to the head safely, without misalignment. As a side effect, this approach also avoids the expensive linearization that pskb_pull triggers on cloned skbs with page fragments. In testing, this resulted in TCP throughput improvements of up to 74%.

In the Linux kernel, the following vulnerability has been resolved: media: cx88: Add missing unmap in snd_cx88_hw_params() In error path, add cx88_alsa_dma_unmap() to release resource acquired by cx88_alsa_dma_map().

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Ignore -EBUSY when checking nested events from vcpu_block() Ignore -EBUSY when checking nested events after exiting a blocking state while L2 is active, as exiting to userspace will generate a spurious userspace exit, usually with KVM_EXIT_UNKNOWN, and likely lead to the VM's demise. Continuing with the wakeup isn't perfect either, as *something* has gone sideways if a vCPU is awakened in L2 with an injected event (or worse, a nested run pending), but continuing on gives the VM a decent chance of surviving without any major side effects. As explained in the Fixes commits, it _should_ be impossible for a vCPU to be put into a blocking state with an already-injected event (exception, IRQ, or NMI). Unfortunately, userspace can stuff MP_STATE and/or injected events, and thus put the vCPU into what should be an impossible state. Don't bother trying to preserve the WARN, e.g. with an anti-syzkaller Kconfig, as WARNs can (hopefully) be added in paths where _KVM_ would be violating x86 architecture, e.g. by WARNing if KVM attempts to inject an exception or interrupt while the vCPU isn't running.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: fix 22000 series SMEM parsing If the firmware were to report three LMACs (which doesn't exist in hardware) then using "fwrt->smem_cfg.lmac[2]" is an overrun of the array. Reject such and use IWL_FW_CHECK instead of WARN_ON in this function.

In the Linux kernel, the following vulnerability has been resolved: media: ipu6: Fix RPM reference leak in probe error paths Several error paths in ipu6_pci_probe() were jumping directly to out_ipu6_bus_del_devices without releasing the runtime PM reference. Add pm_runtime_put_sync() before cleaning up other resources.

In the Linux kernel, the following vulnerability has been resolved: xfs: delete attr leaf freemap entries when empty Back in commit 2a2b5932db6758 ("xfs: fix attr leaf header freemap.size underflow"), Brian Foster observed that it's possible for a small freemap at the end of the end of the xattr entries array to experience a size underflow when subtracting the space consumed by an expansion of the entries array. There are only three freemap entries, which means that it is not a complete index of all free space in the leaf block. This code can leave behind a zero-length freemap entry with a nonzero base. Subsequent setxattr operations can increase the base up to the point that it overlaps with another freemap entry. This isn't in and of itself a problem because the code in _leaf_add that finds free space ignores any freemap entry with zero size. However, there's another bug in the freemap update code in _leaf_add, which is that it fails to update a freemap entry that begins midway through the xattr entry that was just appended to the array. That can result in the freemap containing two entries with the same base but different sizes (0 for the "pushed-up" entry, nonzero for the entry that's actually tracking free space). A subsequent _leaf_add can then allocate xattr namevalue entries on top of the entries array, leading to data loss. But fixing that is for later. For now, eliminate the possibility of confusion by zeroing out the base of any freemap entry that has zero size. Because the freemap is not intended to be a complete index of free space, a subsequent failure to find any free space for a new xattr will trigger block compaction, which regenerates the freemap. It looks like this bug has been in the codebase for quite a long time.

In the Linux kernel, the following vulnerability has been resolved: APEI/GHES: ARM processor Error: don't go past allocated memory If the BIOS generates a very small ARM Processor Error, or an incomplete one, the current logic will fail to deferrence err->section_length and ctx_info->size Add checks to avoid that. With such changes, such GHESv2 records won't cause OOPSes like this: [ 1.492129] Internal error: Oops: 0000000096000005 [#1] SMP [ 1.495449] Modules linked in: [ 1.495820] CPU: 0 UID: 0 PID: 9 Comm: kworker/0:0 Not tainted 6.18.0-rc1-00017-gabadcc3553dd-dirty #18 PREEMPT [ 1.496125] Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 02/02/2022 [ 1.496433] Workqueue: kacpi_notify acpi_os_execute_deferred [ 1.496967] pstate: 814000c5 (Nzcv daIF +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 1.497199] pc : log_arm_hw_error+0x5c/0x200 [ 1.497380] lr : ghes_handle_arm_hw_error+0x94/0x220 0xffff8000811c5324 is in log_arm_hw_error (../drivers/ras/ras.c:75). 70 err_info = (struct cper_arm_err_info *)(err + 1); 71 ctx_info = (struct cper_arm_ctx_info *)(err_info + err->err_info_num); 72 ctx_err = (u8 *)ctx_info; 73 74 for (n = 0; n < err->context_info_num; n++) { 75 sz = sizeof(struct cper_arm_ctx_info) + ctx_info->size; 76 ctx_info = (struct cper_arm_ctx_info *)((long)ctx_info + sz); 77 ctx_len += sz; 78 } 79 and similar ones while trying to access section_length on an error dump with too small size. [ rjw: Subject tweaks ]

In the Linux kernel, the following vulnerability has been resolved: media: radio-keene: fix memory leak in error path Fix a memory leak in usb_keene_probe(). The v4l2 control handler is initialized and controls are added, but if v4l2_device_register() or video_register_device() fails afterward, the handler was never freed, leaking memory. Add v4l2_ctrl_handler_free() call in the err_v4l2 error path to ensure the control handler is properly freed for all error paths after it is initialized.

In the Linux kernel, the following vulnerability has been resolved: media: chips-media: wave5: Fix SError of kernel panic when closed SError of kernel panic rarely happened while testing fluster. The root cause was to enter suspend mode because timeout of autosuspend delay happened. [ 48.834439] SError Interrupt on CPU0, code 0x00000000bf000000 -- SError [ 48.834455] CPU: 0 UID: 0 PID: 1067 Comm: v4l2h265dec0:sr Not tainted 6.12.9-gc9e21a1ebd75-dirty #7 [ 48.834461] Hardware name: ti Texas Instruments J721S2 EVM/Texas Instruments J721S2 EVM, BIOS 2025.01-00345-gbaf3aaa8ecfa 01/01/2025 [ 48.834464] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 48.834468] pc : wave5_dec_clr_disp_flag+0x40/0x80 [wave5] [ 48.834488] lr : wave5_dec_clr_disp_flag+0x40/0x80 [wave5] [ 48.834495] sp : ffff8000856e3a30 [ 48.834497] x29: ffff8000856e3a30 x28: ffff0008093f6010 x27: ffff000809158130 [ 48.834504] x26: 0000000000000000 x25: ffff00080b625000 x24: ffff000804a9ba80 [ 48.834509] x23: ffff000802343028 x22: ffff000809158150 x21: ffff000802218000 [ 48.834513] x20: ffff0008093f6000 x19: ffff0008093f6000 x18: 0000000000000000 [ 48.834518] x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffff74009618 [ 48.834523] x14: 000000010000000c x13: 0000000000000000 x12: 0000000000000000 [ 48.834527] x11: ffffffffffffffff x10: ffffffffffffffff x9 : ffff000802343028 [ 48.834532] x8 : ffff00080b6252a0 x7 : 0000000000000038 x6 : 0000000000000000 [ 48.834536] x5 : ffff00080b625060 x4 : 0000000000000000 x3 : 0000000000000000 [ 48.834541] x2 : 0000000000000000 x1 : ffff800084bf0118 x0 : ffff800084bf0000 [ 48.834547] Kernel panic - not syncing: Asynchronous SError Interrupt [ 48.834549] CPU: 0 UID: 0 PID: 1067 Comm: v4l2h265dec0:sr Not tainted 6.12.9-gc9e21a1ebd75-dirty #7 [ 48.834554] Hardware name: ti Texas Instruments J721S2 EVM/Texas Instruments J721S2 EVM, BIOS 2025.01-00345-gbaf3aaa8ecfa 01/01/2025 [ 48.834556] Call trace: [ 48.834559] dump_backtrace+0x94/0xec [ 48.834574] show_stack+0x18/0x24 [ 48.834579] dump_stack_lvl+0x38/0x90 [ 48.834585] dump_stack+0x18/0x24 [ 48.834588] panic+0x35c/0x3e0 [ 48.834592] nmi_panic+0x40/0x8c [ 48.834595] arm64_serror_panic+0x64/0x70 [ 48.834598] do_serror+0x3c/0x78 [ 48.834601] el1h_64_error_handler+0x34/0x4c [ 48.834605] el1h_64_error+0x64/0x68 [ 48.834608] wave5_dec_clr_disp_flag+0x40/0x80 [wave5] [ 48.834615] wave5_vpu_dec_clr_disp_flag+0x54/0x80 [wave5] [ 48.834622] wave5_vpu_dec_buf_queue+0x19c/0x1a0 [wave5] [ 48.834628] __enqueue_in_driver+0x3c/0x74 [videobuf2_common] [ 48.834639] vb2_core_qbuf+0x508/0x61c [videobuf2_common] [ 48.834646] vb2_qbuf+0xa4/0x168 [videobuf2_v4l2] [ 48.834656] v4l2_m2m_qbuf+0x80/0x238 [v4l2_mem2mem] [ 48.834666] v4l2_m2m_ioctl_qbuf+0x18/0x24 [v4l2_mem2mem] [ 48.834673] v4l_qbuf+0x48/0x5c [videodev] [ 48.834704] __video_do_ioctl+0x180/0x3f0 [videodev] [ 48.834725] video_usercopy+0x2ec/0x68c [videodev] [ 48.834745] video_ioctl2+0x18/0x24 [videodev] [ 48.834766] v4l2_ioctl+0x40/0x60 [videodev] [ 48.834786] __arm64_sys_ioctl+0xa8/0xec [ 48.834793] invoke_syscall+0x44/0x100 [ 48.834800] el0_svc_common.constprop.0+0xc0/0xe0 [ 48.834804] do_el0_svc+0x1c/0x28 [ 48.834809] el0_svc+0x30/0xd0 [ 48.834813] el0t_64_sync_handler+0xc0/0xc4 [ 48.834816] el0t_64_sync+0x190/0x194 [ 48.834820] SMP: stopping secondary CPUs [ 48.834831] Kernel Offset: disabled [ 48.834833] CPU features: 0x08,00002002,80200000,4200421b [ 48.834837] Memory Limit: none [ 49.161404] ---[ end Kernel panic - not syncing: Asynchronous SError Interrupt ]---

In the Linux kernel, the following vulnerability has been resolved: md-cluster: fix NULL pointer dereference in process_metadata_update The function process_metadata_update() blindly dereferences the 'thread' pointer (acquired via rcu_dereference_protected) within the wait_event() macro. While the code comment states "daemon thread must exist", there is a valid race condition window during the MD array startup sequence (md_run): 1. bitmap_load() is called, which invokes md_cluster_ops->join(). 2. join() starts the "cluster_recv" thread (recv_daemon). 3. At this point, recv_daemon is active and processing messages. 4. However, mddev->thread (the main MD thread) is not initialized until later in md_run(). If a METADATA_UPDATED message is received from a remote node during this specific window, process_metadata_update() will be called while mddev->thread is still NULL, leading to a kernel panic. To fix this, we must validate the 'thread' pointer. If it is NULL, we release the held lock (no_new_dev_lockres) and return early, safely ignoring the update request as the array is not yet fully ready to process it.

In the Linux kernel, the following vulnerability has been resolved: xfs: fix freemap adjustments when adding xattrs to leaf blocks xfs/592 and xfs/794 both trip this assertion in the leaf block freemap adjustment code after ~20 minutes of running on my test VMs: ASSERT(ichdr->firstused >= ichdr->count * sizeof(xfs_attr_leaf_entry_t) + xfs_attr3_leaf_hdr_size(leaf)); Upon enabling quite a lot more debugging code, I narrowed this down to fsstress trying to set a local extended attribute with namelen=3 and valuelen=71. This results in an entry size of 80 bytes. At the start of xfs_attr3_leaf_add_work, the freemap looks like this: i 0 base 448 size 0 rhs 448 count 46 i 1 base 388 size 132 rhs 448 count 46 i 2 base 2120 size 4 rhs 448 count 46 firstused = 520 where "rhs" is the first byte past the end of the leaf entry array. This is inconsistent -- the entries array ends at byte 448, but freemap[1] says there's free space starting at byte 388! By the end of the function, the freemap is in worse shape: i 0 base 456 size 0 rhs 456 count 47 i 1 base 388 size 52 rhs 456 count 47 i 2 base 2120 size 4 rhs 456 count 47 firstused = 440 Important note: 388 is not aligned with the entries array element size of 8 bytes. Based on the incorrect freemap, the name area starts at byte 440, which is below the end of the entries array! That's why the assertion triggers and the filesystem shuts down. How did we end up here? First, recall from the previous patch that the freemap array in an xattr leaf block is not intended to be a comprehensive map of all free space in the leaf block. In other words, it's perfectly legal to have a leaf block with: * 376 bytes in use by the entries array * freemap[0] has [base = 376, size = 8] * freemap[1] has [base = 388, size = 1500] * the space between 376 and 388 is free, but the freemap stopped tracking that some time ago If we add one xattr, the entries array grows to 384 bytes, and freemap[0] becomes [base = 384, size = 0]. So far, so good. But if we add a second xattr, the entries array grows to 392 bytes, and freemap[0] gets pushed up to [base = 392, size = 0]. This is bad, because freemap[1] hasn't been updated, and now the entries array and the free space claim the same space. The fix here is to adjust all freemap entries so that none of them collide with the entries array. Note that this fix relies on commit 2a2b5932db6758 ("xfs: fix attr leaf header freemap.size underflow") and the previous patch that resets zero length freemap entries to have base = 0.

Cross Site Scripting vulnerability in Juzaweb CMS v.5.0.0 allows a remote attacker via execute arbitrary code via a crafted script to the Add Banner Ads function

In the Linux kernel, the following vulnerability has been resolved: memory: mtk-smi: fix device leaks on common probe Make sure to drop the reference taken when looking up the SMI device during common probe on late probe failure (e.g. probe deferral) and on driver unbind.

In the Linux kernel, the following vulnerability has been resolved: fs/buffer: add alert in try_to_free_buffers() for folios without buffers try_to_free_buffers() can be called on folios with no buffers attached when filemap_release_folio() is invoked on a folio belonging to a mapping with AS_RELEASE_ALWAYS set but no release_folio operation defined. In such cases, folio_needs_release() returns true because of the AS_RELEASE_ALWAYS flag, but the folio has no private buffer data. This causes try_to_free_buffers() to call drop_buffers() on a folio with no buffers, leading to a null pointer dereference. Adding a check in try_to_free_buffers() to return early if the folio has no buffers attached, with WARN_ON_ONCE() to alert about the misconfiguration. This provides defensive hardening.

In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel/uncore: Skip discovery table for offline dies This warning can be triggered if NUMA is disabled and the system boots with fewer CPUs than the number of CPUs in die 0. WARNING: CPU: 9 PID: 7257 at uncore.c:1157 uncore_pci_pmu_register+0x136/0x160 [intel_uncore] Currently, the discovery table continues to be parsed even if all CPUs in the associated die are offline. This can lead to an array overflow at "pmu->boxes[die] = box" in uncore_pci_pmu_register(), which may trigger the warning above or cause other issues.

In the Linux kernel, the following vulnerability has been resolved: l2tp: Drop large packets with UDP encap syzbot reported a WARN on my patch series [1]. The actual issue is an overflow of 16-bit UDP length field, and it exists in the upstream code. My series added a debug WARN with an overflow check that exposed the issue, that's why syzbot tripped on my patches, rather than on upstream code. syzbot's repro: r0 = socket$pppl2tp(0x18, 0x1, 0x1) r1 = socket$inet6_udp(0xa, 0x2, 0x0) connect$inet6(r1, &(0x7f00000000c0)={0xa, 0x0, 0x0, @loopback, 0xfffffffc}, 0x1c) connect$pppl2tp(r0, &(0x7f0000000240)=@pppol2tpin6={0x18, 0x1, {0x0, r1, 0x4, 0x0, 0x0, 0x0, {0xa, 0x4e22, 0xffff, @ipv4={'\x00', '\xff\xff', @empty}}}}, 0x32) writev(r0, &(0x7f0000000080)=[{&(0x7f0000000000)="ee", 0x34000}], 0x1) It basically sends an oversized (0x34000 bytes) PPPoL2TP packet with UDP encapsulation, and l2tp_xmit_core doesn't check for overflows when it assigns the UDP length field. The value gets trimmed to 16 bites. Add an overflow check that drops oversized packets and avoids sending packets with trimmed UDP length to the wire. syzbot's stack trace (with my patch applied): len >= 65536u WARNING: ./include/linux/udp.h:38 at udp_set_len_short include/linux/udp.h:38 [inline], CPU#1: syz.0.17/5957 WARNING: ./include/linux/udp.h:38 at l2tp_xmit_core net/l2tp/l2tp_core.c:1293 [inline], CPU#1: syz.0.17/5957 WARNING: ./include/linux/udp.h:38 at l2tp_xmit_skb+0x1204/0x18d0 net/l2tp/l2tp_core.c:1327, CPU#1: syz.0.17/5957 Modules linked in: CPU: 1 UID: 0 PID: 5957 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 RIP: 0010:udp_set_len_short include/linux/udp.h:38 [inline] RIP: 0010:l2tp_xmit_core net/l2tp/l2tp_core.c:1293 [inline] RIP: 0010:l2tp_xmit_skb+0x1204/0x18d0 net/l2tp/l2tp_core.c:1327 Code: 0f 0b 90 e9 21 f9 ff ff e8 e9 05 ec f6 90 0f 0b 90 e9 8d f9 ff ff e8 db 05 ec f6 90 0f 0b 90 e9 cc f9 ff ff e8 cd 05 ec f6 90 <0f> 0b 90 e9 de fa ff ff 44 89 f1 80 e1 07 80 c1 03 38 c1 0f 8c 4f RSP: 0018:ffffc90003d67878 EFLAGS: 00010293 RAX: ffffffff8ad985e3 RBX: ffff8881a6400090 RCX: ffff8881697f0000 RDX: 0000000000000000 RSI: 0000000000034010 RDI: 000000000000ffff RBP: dffffc0000000000 R08: 0000000000000003 R09: 0000000000000004 R10: dffffc0000000000 R11: fffff520007acf00 R12: ffff8881baf20900 R13: 0000000000034010 R14: ffff8881a640008e R15: ffff8881760f7000 FS: 000055557e81f500(0000) GS:ffff8882a9467000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000200000033000 CR3: 00000001612f4000 CR4: 00000000000006f0 Call Trace: <TASK> pppol2tp_sendmsg+0x40a/0x5f0 net/l2tp/l2tp_ppp.c:302 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg net/socket.c:742 [inline] sock_write_iter+0x503/0x550 net/socket.c:1195 do_iter_readv_writev+0x619/0x8c0 fs/read_write.c:-1 vfs_writev+0x33c/0x990 fs/read_write.c:1059 do_writev+0x154/0x2e0 fs/read_write.c:1105 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x14d/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f636479c629 Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffffd4241c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000014 RAX: ffffffffffffffda RBX: 00007f6364a15fa0 RCX: 00007f636479c629 RDX: 0000000000000001 RSI: 0000200000000080 RDI: 0000000000000003 RBP: 00007f6364832b39 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007f6364a15fac R14: 00007f6364a15fa0 R15: 00007f6364a15fa0 </TASK> [1]: https://lore.kernel.org/all/[email protected]/

In the Linux kernel, the following vulnerability has been resolved: net: Drop the lock in skb_may_tx_timestamp() skb_may_tx_timestamp() may acquire sock::sk_callback_lock. The lock must not be taken in IRQ context, only softirq is okay. A few drivers receive the timestamp via a dedicated interrupt and complete the TX timestamp from that handler. This will lead to a deadlock if the lock is already write-locked on the same CPU. Taking the lock can be avoided. The socket (pointed by the skb) will remain valid until the skb is released. The ->sk_socket and ->file member will be set to NULL once the user closes the socket which may happen before the timestamp arrives. If we happen to observe the pointer while the socket is closing but before the pointer is set to NULL then we may use it because both pointer (and the file's cred member) are RCU freed. Drop the lock. Use READ_ONCE() to obtain the individual pointer. Add a matching WRITE_ONCE() where the pointer are cleared.

In the Linux kernel, the following vulnerability has been resolved: net: ipa: fix GENERIC_CMD register field masks for IPA v5.0+ Fix the field masks to match the hardware layout documented in downstream GSI (GSI_V3_0_EE_n_GSI_EE_GENERIC_CMD_*). Notably this fixes a WARN I was seeing when I tried to send "stop" to the MPSS remoteproc while IPA was up.

In Paramiko through 4.0.0 before a448945, rsakey.py allows the SHA-1 algorithm.

Jupyter Server is the backend for Jupyter web applications. In versions 2.17.0 and earlier, the secret used to sign authentication cookies is persisted to a static file at ~/.local/share/jupyter/runtime/jupyter_cookie_secret and is never rotated when a user changes their password. After a password reset and server restart, any previously issued authentication cookie remains cryptographically valid because the signing key has not changed. An attacker who has captured a session cookie through any means retains full authenticated access to the server regardless of subsequent password changes. This affects deployments using password-based authentication, particularly shared or public-facing servers where credential rotation is expected to revoke existing sessions. This issue has been fixed in version 2.18.0.

Heap-based Buffer Overflow vulnerability in mod_proxy_ajp of Apache HTTP Server. If mod_proxy_ajp connects to a malicious AJP server this AJP server can send a malicious AJP message back to mod_proxy_ajp and cause it to write 4 attacker controlled bytes after the end of a heap based buffer. This issue affects Apache HTTP Server: through 2.4.66. Users are recommended to upgrade to version 2.4.67, which fixes the issue.

Jupyter Server is the backend for Jupyter web applications. In versions 2.17.0 and earlier, the Origin header validation uses Python's re.match() to check incoming origins against the allow_origin_pat configuration value. Because re.match() only anchors at the start of the string and does not require a full match, a pattern intended to match only a trusted domain (e.g., trusted.example.com) will also match any origin that begins with that domain followed by additional characters (e.g., trusted.example.com.evil.com). An attacker who controls such a domain can bypass the CORS origin restriction and make cross-origin requests to the Jupyter Server API from an untrusted site. This issue has been fixed in version 2.18.0.

OpenMRS Core is an open source electronic medical record system platform. In versions 2.7.8 and earlier and versions 2.8.0 through 2.8.5, the `/openmrs/moduleResources/{moduleid}` endpoint is vulnerable to a path traversal attack. The ModuleResourcesServlet constructs a filesystem path from user-controlled input without performing path boundary validation — the getFile() method concatenates the user-supplied path into an absolute filesystem path without calling normalize() or checking that the result stays within the allowed module resources directory. Because this endpoint serves static resources required for rendering the login page, it is not protected by authentication filters, allowing unauthenticated exploitation. An attacker can traverse directories and read arbitrary files from the server filesystem, including /etc/passwd and application configuration files containing database credentials. Successful exploitation requires the target deployment to run on Apache Tomcat versions prior to 8.5.31, where the ..; path parameter bypass is not mitigated by the container. Deployments on Tomcat 8.5.31 or later and Tomcat 9.0.10 or later are protected at the container level, though the underlying code defect remains. This issue has been fixed in versions after 2.7.8 (within the 2.7.x branch) and in version 2.8.6 and later.

In versions 2.1.63 through 2.1.83 of Claude Code, the folder trust determination logic used the git worktree commondir file without validating its contents. An attacker could craft a malicious repository with a commondir file pointing to a path the victim had previously trusted, causing Claude Code to bypass its trust confirmation dialog and immediately execute hooks defined in `.claude/settings.json`. Exploitation requires the victim to clone the malicious repository and run Claude Code within it, and the attacker must know or guess a path the victim had already trusted. This issue has been fixed in version 2.1.84.

Pi-hole FTL is the core engine of the Pi-hole network-level advertisement and tracker blocker. In versions before 6.6.1, the `dns.interface` configuration field in Pi-hole FTL accepted newline characters without validation, allowing an attacker to inject arbitrary directives into the generated dnsmasq configuration file. On installations with no admin password set (the default for many deployments), the configuration API is fully accessible without credentials, allowing a network-adjacent attacker to inject the payload, enable the built-in DHCP server, and achieve arbitrary command execution on the host the next time any device on the network requests a DHCP lease. The injected value is persisted to /etc/pihole/pihole.toml and survives restarts. The strncpy in the code path limits the total interface field to 31 bytes, but payloads such as wlan0\ndhcp-script=/tmp/p fit within this constraint. The dnsmasq config validation introduced in FTL 6.6 only checks syntactic validity, so valid directives injected via newline pass validation successfully. This issue has been fixed in version 6.6.1.

lxc is a Linux container runtime. In the setuid helper lxc-user-nic, the delete path contains a logic flaw in the find_line() function that allows an unprivileged user to delete OVS-attached network interfaces belonging to other users. When lxc-user-nic delete scans its NIC database to authorize a deletion request, the interface name comparison can set the authorization flag based on a name match alone, even when the ownership, type, and link fields in that database entry belong to a different user. The vulnerable check sits after the goto next label handling, meaning it is reachable on lines where earlier ownership checks failed or were skipped. Because nothing downstream of this authorization signal re-verifies that the matched database line actually belongs to the caller, an unprivileged attacker with a valid lxc-usernet policy entry can trigger deletion of another user's OVS port on the same bridge. This is limited to multi-tenant environments using lxc-user-nic with OpenVSwitch bridges. The impact is denial of service - one tenant can repeatedly disconnect networking from containers run by another tenant on shared infrastructure. This is patched in version 7.0.0.

Gotenberg is an API-based document conversion tool. In version 8.29.1, an unauthenticated attacker with network access can force the server to make outbound HTTP POST requests to arbitrary internal or external destinations by supplying a crafted URL in the Gotenberg-Webhook-Url request header. The FilterDeadline function in filter.go is intended to gate outbound URLs, but when both the allow-list and deny-list are empty (the default configuration), it returns nil unconditionally and permits any URL. This is a blind SSRF: Gotenberg POSTs the converted document to the webhook URL and only checks whether the response status code is an error, but never returns the target's response body to the attacker. An attacker can use this to probe internal network infrastructure by observing whether the error callback is invoked, force POST requests against internal services that perform side effects, and confirm reachability of cloud metadata endpoints. The retryable HTTP client issues up to 4 automatic retries per request, amplifying each probe. This issue has been fixed in version 8.31.0. As a workaround, configure the GOTENBERG_API_WEBHOOK_ALLOW_LIST environment variable to restrict webhook URLs to known receivers, or set GOTENBERG_API_WEBHOOK_DENY_LIST to block RFC-1918 and link-local address ranges.

Dify before version 1.14.0 contains an authorization bypass vulnerability that allows authenticated users to read the full contents of files uploaded by other users within the same tenant by supplying an arbitrary file UUID in the files array of a chat-messages request. Attackers can exploit insufficient permission verification in the chat-messages endpoints to access files without ownership validation, bypassing workspace separation and signed URL protections to retrieve sensitive file contents through workflow processing.

CoreDNS is a DNS server written in Go. In versions prior to 1.14.3, the gRPC, QUIC, DoH, and DoH3 transport implementations incorrectly handle TSIG authentication. For gRPC and QUIC, the server checks whether the TSIG key name exists in the configuration but never calls dns.TsigVerify() to validate the HMAC. If the key name matches a configured key, the tsigStatus field remains nil and the tsig plugin treats the request as successfully authenticated regardless of the MAC value. For DoH and DoH3, the issue is more severe: the DoHWriter.TsigStatus() method unconditionally returns nil, and the server never inspects the TSIG record at all. Any request containing a TSIG record is treated as authenticated over DoH and DoH3, even if the key name is invalid and the MAC is arbitrary. An unauthenticated network attacker can exploit this to bypass TSIG-protected functionality such as AXFR/IXFR zone transfers, dynamic DNS updates, or other TSIG-gated plugin behavior. The DoH and DoH3 variants have a lower exploitation bar because the attacker does not need to know a valid TSIG key name. This issue has been fixed in version 1.14.3. As a workaround, disable gRPC, QUIC, DoH, and DoH3 listeners where TSIG authentication is required, or restrict network-level access to affected transport ports to trusted sources only.

** REJECT ** DO NOT USE THIS CANDIDATE NUMBER. ConsultIDs: CVE-2026-34429. Reason: This candidate is a duplicate of CVE-2026-34429. Notes: All CVE users should reference CVE-2026-34429 instead of this candidate.

Incus is an open source container and virtual machine manager. In versions prior to 7.0.0, the image import flow issues an outbound HEAD request to a user-supplied URL before validating the request against project restrictions such as restricted.images.servers. The imgPostURLInfo function constructs and sends a HEAD request directly from the attacker-supplied source URL to resolve image metadata, and this network interaction occurs before the flow reaches the point where the import would be rejected by policy. Although the actual image download is blocked by the project restriction, an authenticated user can coerce the daemon into making blind HEAD requests to arbitrary destinations. These requests include server metadata in custom headers (Incus-Server-Architectures, Incus-Server-Version), which discloses information about the host environment to the attacker-controlled endpoint. This blind SSRF primitive can be used to probe internal services, unroutable address space, or cloud metadata endpoints reachable from the host. This vulnerability pattern is similar to CVE-2026-24767. This issue has been fixed in version 7.0.0.

Gotenberg is an API-based document conversion tool. In versions 8.30.1 and earlier, the default private-IP deny-lists for the --webhook-deny-list and --api-download-from-deny-list flags use a case-sensitive regular expression (^https?://) to match URL schemes. Because Go's net/url.Parse() normalizes the scheme to lowercase before establishing the outbound TCP connection, an attacker can bypass the deny-list by simply capitalizing part of the URL scheme (e.g., HTTP://, HTTPS://, or Http://). This allows unauthenticated requests to reach internal network services, including private IP ranges, loopback addresses, and cloud instance metadata endpoints such as HTTP://169.254.169.254/latest/meta-data/. This bypasses the same security control that was patched in CVE-2026-27018. This issue has been fixed in version 8.31.0.

Masa CMS is an open source content management system. In versions 7.2.0 through 7.2.9, 7.3.0 through 7.3.14, 7.4.0 through 7.4.9, and 7.5.0 through 7.5.2, the unauthenticated JSON API accepts an altTable parameter that is stored via the setAltTable() method without validation or sanitization. This value is injected directly into a SQL FROM clause within feedGateway.cfc. An unauthenticated attacker can pass an arbitrary subquery into the altTable parameter to read sensitive data from any table in the database in a single HTTP request, including administrative credentials and password reset tokens. This issue has been fixed in versions 7.2.10, 7.3.15, 7.4.10, and 7.5.3. As a workaround, apply validation to the setAltTable function in core/mura/content/feed/feedBean.cfc to restrict input to simple alphanumeric table names, or disable the JSON API if it is not required.

Masa CMS is an open source content management system. In versions 7.2.0 through 7.2.9, 7.3.0 through 7.3.14, 7.4.0 through 7.4.9, and 7.5.0 through 7.5.2, a SQL injection vulnerability exists in the beanFeed.cfc component within the getQuery function's handling of the sortDirection parameter. The parameter value is concatenated directly into SQL queries without sanitization or parameterization. An unauthenticated remote attacker can exploit this to extract sensitive information, modify or delete database records, or potentially achieve remote code execution on the underlying database server. This issue has been fixed in versions 7.2.10, 7.3.15, 7.4.10, and 7.5.3. As a workaround, use a WAF to block or restrict access to the beanFeed.cfc component, or deploy rules to detect SQL injection patterns targeting the sortDirection parameter.

Masa CMS is an open source content management system. In versions 7.5.2 and earlier, a SQL injection vulnerability exists in the beanFeed.cfc component within the getQuery function's processing of the sortBy parameter. The application fails to properly sanitize or parameterize this input before incorporating it into dynamic SQL statements. An unauthenticated remote attacker can execute arbitrary SQL commands against the database, potentially gaining access to sensitive data, modifying or deleting records, or escalating privileges to administrative control. This issue has been fixed in versions 7.2.10, 7.3.15, 7.4.10, and 7.5.3. As a workaround, configure WAF rules to block malicious SQL patterns in the sortBy parameter sent to beanFeed.cfc.

In ProFTPD through 1.3.9a before 7666224, a SQL injection vulnerability in sqltab_fetch_clients_cb() in contrib/mod_wrap2_sql.c allows a remote attacker to inject arbitrary SQL commands via a crafted domain name that is accessed in a reverse DNS lookup. When "UseReverseDNS on" is enabled, the attacker-supplied hostname is passed unescaped into SQL queries. The character restrictions of DNS names may affect exploitability.

PhpSpreadsheet is a library for reading and writing spreadsheet files. In versions 1.30.3 and earlier, 2.0.0 through 2.1.15, 2.2.0 through 2.4.4, 3.3.0 through 3.10.4, and 4.0.0 through 5.6.0, the HTML Writer skips htmlspecialchars() output escaping when a cell uses a custom number format containing the @ text placeholder with additional literal text (e.g., @ "items"). The escaping is only applied when the formatted output strictly equals the original cell value. When the format code contains @ with quoted literal text, the formatter substitutes the raw cell value into the format string and returns early without invoking the escaping callback. An attacker who can control cell content in a spreadsheet processed by the HTML Writer can inject arbitrary HTML and JavaScript into the generated output. This issue has been fixed in versions 1.30.4, 2.1.16, 2.4.5, 3.10.5, and 5.7.0.

Jupyter Server is the backend for Jupyter web applications. In versions 2.17.0 and earlier, a path traversal vulnerability in the REST API allows an authenticated user to escape the configured root_dir and access sibling directories whose names begin with the same prefix as the root_dir. For example, with a root_dir named "test", the API permits access to a sibling directory named "testtest" through a crafted request to the /api/contents endpoint using encoded path components. An attacker can read, write, and delete files in affected sibling directories. Multi-tenant deployments using predictable naming schemes are particularly at risk, as a user with a directory named "user1" could access directories for user10 through user19 and beyond. A user who can choose a single-character folder name could gain access to a significant number of sibling directories. Version 2.18.0 contains a fix. As a workaround, ensure folder names do not share a common prefix with any sibling directory.

Sandboxie-Plus is an open source sandbox-based isolation software for Windows. In versions 1.17.2 and earlier, a Time-of-Check-to-Time-of-Use (TOCTOU) race condition exists during addon installation. When a user installs an addon through the SandMan interface, UpdUtil.exe is spawned as SYSTEM by SbieSvc but stages files in the user-writable %TEMP%\sandboxie-updater directory. After UpdUtil verifies file hashes against the signed addon manifest, install.bat extracts files.cab and executes config.exe from its contents. Between hash verification and extraction, an unprivileged user can replace files.cab with a crafted cabinet containing a malicious executable, which is then run as SYSTEM. No UAC prompt is required. This issue has been fixed in version 1.17.3.

Sandboxie-Plus is an open source sandbox-based isolation software for Windows. In versions 1.17.2 and earlier, SbieIniServer::HashPassword converts a SHA-1 digest to hexadecimal incorrectly. The high nibble of each byte is shifted right by 8 instead of 4, which always produces zero for an 8-bit value. As a result, the stored EditPassword hash only preserves the low nibble of each digest byte, reducing the effective entropy from 160 bits to 80 bits. This is layered on top of an unsalted SHA-1 scheme. The reduced entropy makes leaked or backed-up password hashes materially easier to brute-force. This issue has been fixed in version 1.17.3.

Sandboxie-Plus is an open source sandbox-based isolation software for Windows. In versions 1.17.2 and earlier, NamedPipeServer::OpenHandler copies the server field from NAMED_PIPE_OPEN_REQ into a fixed WCHAR pipename[160] stack buffer using wcscat without verifying null termination. The handler only enforces a minimum packet size, and since the service pipe accepts variable-length messages, a sandboxed caller can fill the server[48] field with non-zero data and append additional controlled wide characters after the structure. wcscat then reads past the fixed field and overflows the stack buffer in the SYSTEM service. This message is restricted to sandboxed callers, making it a sandbox escape vector. This can lead to a crash of the SbieSvc service or potential code execution as SYSTEM. This issue has been fixed in version 1.17.3.

Sandboxie-Plus is an open source sandbox-based isolation software for Windows. In versions 1.17.2 and earlier, several ProcessServer handlers (KillAllHandler, SuspendAllHandler, and RunSandboxedHandler) copy a WCHAR boxname[34] field from request structures into WCHAR[40] stack buffers using wcscpy without verifying null termination. Because the service pipe accepts variable-length packets larger than the request structure, an attacker can fill the boxname field with non-zero data and append additional controlled wide characters after the structure. wcscpy then reads past the fixed field and overflows the destination stack buffer. The service pipe is created with a NULL DACL, allowing any local process to connect, and the unsafe copy occurs before authorization checks. This can lead to a crash of the SbieSvc service or potential code execution as SYSTEM. This issue has been fixed in version 1.17.3.

Sandboxie-Plus is an open source sandbox-based isolation software for Windows. In versions 1.17.2 and earlier, the SbieIniServer RunSbieCtrl handler contains a stack buffer overflow. The MSGID_SBIE_INI_RUN_SBIE_CTRL message is handled before normal sandbox and impersonation checks, and for non-sandboxed callers, the handler copies the trailing message payload into a fixed-size WCHAR ctrlCmd[128] stack buffer using memcpy without verifying the length fits within the buffer. The service pipe is created with a NULL DACL, allowing any local interactive process to connect and send an oversized payload to overflow the stack. This can lead to a crash of the SbieSvc service or potential code execution as SYSTEM. This issue has been fixed in version 1.17.3.