CVE Feed

In the Linux kernel, the following vulnerability has been resolved: net: macb: Shuffle the tx ring before enabling tx Quanyang observed that when using an NFS rootfs on an AMD ZynqMp board, the rootfs may take an extended time to recover after a suspend. Upon investigation, it was determined that the issue originates from a problem in the macb driver. According to the Zynq UltraScale TRM [1], when transmit is disabled, the transmit buffer queue pointer resets to point to the address specified by the transmit buffer queue base address register. In the current implementation, the code merely resets `queue->tx_head` and `queue->tx_tail` to '0'. This approach presents several issues: - Packets already queued in the tx ring are silently lost, leading to memory leaks since the associated skbs cannot be released. - Concurrent write access to `queue->tx_head` and `queue->tx_tail` may occur from `macb_tx_poll()` or `macb_start_xmit()` when these values are reset to '0'. - The transmission may become stuck on a packet that has already been sent out, with its 'TX_USED' bit set, but has not yet been processed. However, due to the manipulation of 'queue->tx_head' and 'queue->tx_tail', `macb_tx_poll()` incorrectly assumes there are no packets to handle because `queue->tx_head == queue->tx_tail`. This issue is only resolved when a new packet is placed at this position. This is the root cause of the prolonged recovery time observed for the NFS root filesystem. To resolve this issue, shuffle the tx ring and tx skb array so that the first unsent packet is positioned at the start of the tx ring. Additionally, ensure that updates to `queue->tx_head` and `queue->tx_tail` are properly protected with the appropriate lock. [1] https://docs.amd.com/v/u/en-US/ug1085-zynq-ultrascale-trm

In the Linux kernel, the following vulnerability has been resolved: btrfs: add missing RCU unlock in error path in try_release_subpage_extent_buffer() Call rcu_read_lock() before exiting the loop in try_release_subpage_extent_buffer() because there is a rcu_read_unlock() call past the loop. This has been detected by the Clang thread-safety analyzer.

In the Linux kernel, the following vulnerability has been resolved: USB: dummy-hcd: Fix interrupt synchronization error This fixes an error in synchronization in the dummy-hcd driver. The error has a somewhat involved history. The synchronization mechanism was introduced by commit 7dbd8f4cabd9 ("USB: dummy-hcd: Fix erroneous synchronization change"), which added an emulated "interrupts enabled" flag together with code emulating synchronize_irq() (it waits until all current handler callbacks have returned). But the emulated interrupt-disable occurred too late, after the driver containing the handler callback routines had been told that it was unbound and no more callbacks would occur. Commit 4a5d797a9f9c ("usb: gadget: dummy_hcd: fix gpf in gadget_setup") tried to fix this by moving the synchronize_irq() emulation code from dummy_stop() to dummy_pullup(), which runs before the unbind callback. There still were races, though, because the emulated interrupt-disable still occurred too late. It couldn't be moved to dummy_pullup(), because that routine can be called for reasons other than an impending unbind. Therefore commits 7dc0c55e9f30 ("USB: UDC core: Add udc_async_callbacks gadget op") and 04145a03db9d ("USB: UDC: Implement udc_async_callbacks in dummy-hcd") added an API allowing the UDC core to tell dummy-hcd exactly when emulated interrupts and their callbacks should be disabled. That brings us to the current state of things, which is still wrong because the emulated synchronize_irq() occurs before the emulated interrupt-disable! That's no good, beause it means that more emulated interrupts can occur after the synchronize_irq() emulation has run, leading to the possibility that a callback handler may be running when the gadget driver is unbound. To fix this, we have to move the synchronize_irq() emulation code yet again, to the dummy_udc_async_callbacks() routine, which takes care of enabling and disabling emulated interrupt requests. The synchronization will now run immediately after emulated interrupts are disabled, which is where it belongs.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: Fix UAF in le_read_features_complete This fixes the following backtrace caused by hci_conn being freed before le_read_features_complete but after hci_le_read_remote_features_sync so hci_conn_del -> hci_cmd_sync_dequeue is not able to prevent it: ================================================================== BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:96 [inline] BUG: KASAN: slab-use-after-free in atomic_dec_and_test include/linux/atomic/atomic-instrumented.h:1383 [inline] BUG: KASAN: slab-use-after-free in hci_conn_drop include/net/bluetooth/hci_core.h:1688 [inline] BUG: KASAN: slab-use-after-free in le_read_features_complete+0x5b/0x340 net/bluetooth/hci_sync.c:7344 Write of size 4 at addr ffff8880796b0010 by task kworker/u9:0/52 CPU: 0 UID: 0 PID: 52 Comm: kworker/u9:0 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xcd/0x630 mm/kasan/report.c:482 kasan_report+0xe0/0x110 mm/kasan/report.c:595 check_region_inline mm/kasan/generic.c:194 [inline] kasan_check_range+0x100/0x1b0 mm/kasan/generic.c:200 instrument_atomic_read_write include/linux/instrumented.h:96 [inline] atomic_dec_and_test include/linux/atomic/atomic-instrumented.h:1383 [inline] hci_conn_drop include/net/bluetooth/hci_core.h:1688 [inline] le_read_features_complete+0x5b/0x340 net/bluetooth/hci_sync.c:7344 hci_cmd_sync_work+0x1ff/0x430 net/bluetooth/hci_sync.c:334 process_one_work+0x9ba/0x1b20 kernel/workqueue.c:3257 process_scheduled_works kernel/workqueue.c:3340 [inline] worker_thread+0x6c8/0xf10 kernel/workqueue.c:3421 kthread+0x3c5/0x780 kernel/kthread.c:463 ret_from_fork+0x983/0xb10 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246 </TASK> Allocated by task 5932: kasan_save_stack+0x33/0x60 mm/kasan/common.c:56 kasan_save_track+0x14/0x30 mm/kasan/common.c:77 poison_kmalloc_redzone mm/kasan/common.c:400 [inline] __kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:417 kmalloc_noprof include/linux/slab.h:957 [inline] kzalloc_noprof include/linux/slab.h:1094 [inline] __hci_conn_add+0xf8/0x1c70 net/bluetooth/hci_conn.c:963 hci_conn_add_unset+0x76/0x100 net/bluetooth/hci_conn.c:1084 le_conn_complete_evt+0x639/0x1f20 net/bluetooth/hci_event.c:5714 hci_le_enh_conn_complete_evt+0x23d/0x380 net/bluetooth/hci_event.c:5861 hci_le_meta_evt+0x357/0x5e0 net/bluetooth/hci_event.c:7408 hci_event_func net/bluetooth/hci_event.c:7716 [inline] hci_event_packet+0x685/0x11c0 net/bluetooth/hci_event.c:7773 hci_rx_work+0x2c9/0xeb0 net/bluetooth/hci_core.c:4076 process_one_work+0x9ba/0x1b20 kernel/workqueue.c:3257 process_scheduled_works kernel/workqueue.c:3340 [inline] worker_thread+0x6c8/0xf10 kernel/workqueue.c:3421 kthread+0x3c5/0x780 kernel/kthread.c:463 ret_from_fork+0x983/0xb10 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246 Freed by task 5932: kasan_save_stack+0x33/0x60 mm/kasan/common.c:56 kasan_save_track+0x14/0x30 mm/kasan/common.c:77 __kasan_save_free_info+0x3b/0x60 mm/kasan/generic.c:587 kasan_save_free_info mm/kasan/kasan.h:406 [inline] poison_slab_object mm/kasan/common.c:252 [inline] __kasan_slab_free+0x5f/0x80 mm/kasan/common.c:284 kasan_slab_free include/linux/kasan.h:234 [inline] slab_free_hook mm/slub.c:2540 [inline] slab_free mm/slub.c:6663 [inline] kfree+0x2f8/0x6e0 mm/slub.c:6871 device_release+0xa4/0x240 drivers/base/core.c:2565 kobject_cleanup lib/kobject.c:689 [inline] kobject_release lib/kobject.c:720 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0x1e7/0x590 lib/kobject. ---truncated---

The socket connection handler in aswArPot.sys in the Avast and AVG Windows Anti Rootkit driver before 22.1 allows local attackers to execute arbitrary code in kernel mode or cause a denial of service (memory corruption and OS crash) due to a double fetch vulnerability at aswArPot+0xc4a3.

A Cross Site Scripting vulnerability in Alkacon OpenCms before 10.5.1 exists via cmis-online/type.

In Thruk Monitoring through 2.46.3, the login field of the login form is vulnerable to reflected XSS. This vulnerability can be exploited by unauthenticated remote attackers to target users of the monitoring interface.

/cgi-bin/time.cgi in Atlona AT-OME-MS42 Matrix Switcher 1.1.2 allow remote authenticated users to execute arbitrary commands as root via a POST request that carries a serverName parameter.

In the Linux kernel, the following vulnerability has been resolved: media: rockchip: rga: Fix possible ERR_PTR dereference in rga_buf_init() rga_get_frame() can return ERR_PTR(-EINVAL) when buffer type is unsupported or invalid. rga_buf_init() does not check the return value and unconditionally dereferences the pointer when accessing f->size. Add proper ERR_PTR checking and return the error to prevent dereferencing an invalid pointer.

In the Linux kernel, the following vulnerability has been resolved: USB: dummy-hcd: Fix locking/synchronization error Syzbot testing was able to provoke an addressing exception and crash in the usb_gadget_udc_reset() routine in drivers/usb/gadgets/udc/core.c, resulting from the fact that the routine was called with a second ("driver") argument of NULL. The bad caller was set_link_state() in dummy_hcd.c, and the problem arose because of a race between a USB reset and driver unbind. These sorts of races were not supposed to be possible; commit 7dbd8f4cabd9 ("USB: dummy-hcd: Fix erroneous synchronization change"), along with a few followup commits, was written specifically to prevent them. As it turns out, there are (at least) two errors remaining in the code. Another patch will address the second error; this one is concerned with the first. The error responsible for the syzbot crash occurred because the stop_activity() routine will sometimes drop and then re-acquire the dum->lock spinlock. A call to stop_activity() occurs in set_link_state() when handling an emulated USB reset, after the test of dum->ints_enabled and before the increment of dum->callback_usage. This allowed another thread (doing a driver unbind) to sneak in and grab the spinlock, and then clear dum->ints_enabled and dum->driver. Normally this other thread would have to wait for dum->callback_usage to go down to 0 before it would clear dum->driver, but in this case it didn't have to wait since dum->callback_usage had not yet been incremented. The fix is to increment dum->callback_usage _before_ calling stop_activity() instead of after. Then the thread doing the unbind will not clear dum->driver until after the call to usb_gadget_udc_reset() safely returns and dum->callback_usage has been decremented again.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_subset: Fix unbalanced refcnt in geth_free geth_alloc() increments the reference count, but geth_free() fails to decrement it. This prevents the configuration of attributes via configfs after unlinking the function. Decrement the reference count in geth_free() to ensure proper cleanup.

In the Linux kernel, the following vulnerability has been resolved: net: ipa: fix event ring index not programmed for IPA v5.0+ For IPA v5.0+, the event ring index field moved from CH_C_CNTXT_0 to CH_C_CNTXT_1. The v5.0 register definition intended to define this field in the CH_C_CNTXT_1 fmask array but used the old identifier of ERINDEX instead of CH_ERINDEX. Without a valid event ring, GSI channels could never signal transfer completions. This caused gsi_channel_trans_quiesce() to block forever in wait_for_completion(). At least for IPA v5.2 this resolves an issue seen where runtime suspend, system suspend, and remoteproc stop all hanged forever. It also meant the IPA data path was completely non functional.

In the Linux kernel, the following vulnerability has been resolved: iio: imu: adis: Fix NULL pointer dereference in adis_init The adis_init() function dereferences adis->ops to check if the individual function pointers (write, read, reset) are NULL, but does not first check if adis->ops itself is NULL. Drivers like adis16480, adis16490, adis16545 and others do not set custom ops and rely on adis_init() assigning the defaults. Since struct adis is zero-initialized by devm_iio_device_alloc(), adis->ops is NULL when adis_init() is called, causing a NULL pointer dereference: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 pc : adis_init+0xc0/0x118 Call trace: adis_init+0xc0/0x118 adis16480_probe+0xe0/0x670 Fix this by checking if adis->ops is NULL before dereferencing it, falling through to assign the default ops in that case.

In the Linux kernel, the following vulnerability has been resolved: net: ncsi: fix skb leak in error paths Early return paths in NCSI RX and AEN handlers fail to release the received skb, resulting in a memory leak. Specifically, ncsi_aen_handler() returns on invalid AEN packets without consuming the skb. Similarly, ncsi_rcv_rsp() exits early when failing to resolve the NCSI device, response handler, or request, leaving the skb unfreed.

In the Linux kernel, the following vulnerability has been resolved: net: mctp: fix device leak on probe failure Driver core holds a reference to the USB interface and its parent USB device while the interface is bound to a driver and there is no need to take additional references unless the structures are needed after disconnect. This driver takes a reference to the USB device during probe but does not to release it on probe failures. Drop the redundant device reference to fix the leak, reduce cargo culting, make it easier to spot drivers where an extra reference is needed, and reduce the risk of further memory leaks.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: Don't log keys in SMB3 signing and encryption key generation When KSMBD_DEBUG_AUTH logging is enabled, generate_smb3signingkey() and generate_smb3encryptionkey() log the session, signing, encryption, and decryption key bytes. Remove the logs to avoid exposing credentials.

In the Linux kernel, the following vulnerability has been resolved: smb: server: fix use-after-free in smb2_open() The opinfo pointer obtained via rcu_dereference(fp->f_opinfo) is dereferenced after rcu_read_unlock(), creating a use-after-free window.

In the Linux kernel, the following vulnerability has been resolved: mm: Fix a hmm_range_fault() livelock / starvation problem If hmm_range_fault() fails a folio_trylock() in do_swap_page, trying to acquire the lock of a device-private folio for migration, to ram, the function will spin until it succeeds grabbing the lock. However, if the process holding the lock is depending on a work item to be completed, which is scheduled on the same CPU as the spinning hmm_range_fault(), that work item might be starved and we end up in a livelock / starvation situation which is never resolved. This can happen, for example if the process holding the device-private folio lock is stuck in migrate_device_unmap()->lru_add_drain_all() sinc lru_add_drain_all() requires a short work-item to be run on all online cpus to complete. A prerequisite for this to happen is: a) Both zone device and system memory folios are considered in migrate_device_unmap(), so that there is a reason to call lru_add_drain_all() for a system memory folio while a folio lock is held on a zone device folio. b) The zone device folio has an initial mapcount > 1 which causes at least one migration PTE entry insertion to be deferred to try_to_migrate(), which can happen after the call to lru_add_drain_all(). c) No or voluntary only preemption. This all seems pretty unlikely to happen, but indeed is hit by the "xe_exec_system_allocator" igt test. Resolve this by waiting for the folio to be unlocked if the folio_trylock() fails in do_swap_page(). Rename migration_entry_wait_on_locked() to softleaf_entry_wait_unlock() and update its documentation to indicate the new use-case. Future code improvements might consider moving the lru_add_drain_all() call in migrate_device_unmap() to be called *after* all pages have migration entries inserted. That would eliminate also b) above. v2: - Instead of a cond_resched() in hmm_range_fault(), eliminate the problem by waiting for the folio to be unlocked in do_swap_page() (Alistair Popple, Andrew Morton) v3: - Add a stub migration_entry_wait_on_locked() for the !CONFIG_MIGRATION case. (Kernel Test Robot) v4: - Rename migrate_entry_wait_on_locked() to softleaf_entry_wait_on_locked() and update docs (Alistair Popple) v5: - Add a WARN_ON_ONCE() for the !CONFIG_MIGRATION version of softleaf_entry_wait_on_locked(). - Modify wording around function names in the commit message (Andrew Morton) (cherry picked from commit a69d1ab971a624c6f112cea61536569d579c3215)

In the Linux kernel, the following vulnerability has been resolved: firmware: stratix10-rsu: Fix NULL pointer dereference when RSU is disabled When the Remote System Update (RSU) isn't enabled in the First Stage Boot Loader (FSBL), the driver encounters a NULL pointer dereference when excute svc_normal_to_secure_thread() thread, resulting in a kernel panic: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 Mem abort info: ... Data abort info: ... [0000000000000008] user address but active_mm is swapper Internal error: Oops: 0000000096000004 [#1] SMP Modules linked in: CPU: 0 UID: 0 PID: 79 Comm: svc_smc_hvc_thr Not tainted 6.19.0-rc8-yocto-standard+ #59 PREEMPT Hardware name: SoCFPGA Stratix 10 SoCDK (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : svc_normal_to_secure_thread+0x38c/0x990 lr : svc_normal_to_secure_thread+0x144/0x990 ... Call trace: svc_normal_to_secure_thread+0x38c/0x990 (P) kthread+0x150/0x210 ret_from_fork+0x10/0x20 Code: 97cfc113 f9400260 aa1403e1 f9400400 (f9400402) ---[ end trace 0000000000000000 ]--- The issue occurs because rsu_send_async_msg() fails when RSU is not enabled in firmware, causing the channel to be freed via stratix10_svc_free_channel(). However, the probe function continues execution and registers svc_normal_to_secure_thread(), which subsequently attempts to access the already-freed channel, triggering the NULL pointer dereference. Fix this by properly cleaning up the async client and returning early on failure, preventing the thread from being used with an invalid channel.

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Fix runtime suspend deadlock when there is pending job The runtime suspend callback drains the running job workqueue before suspending the device. If a job is still executing and calls pm_runtime_resume_and_get(), it can deadlock with the runtime suspend path. Fix this by moving pm_runtime_resume_and_get() from the job execution routine to the job submission routine, ensuring the device is resumed before the job is queued and avoiding the deadlock during runtime suspend.

In the Linux kernel, the following vulnerability has been resolved: unshare: fix unshare_fs() handling There's an unpleasant corner case in unshare(2), when we have a CLONE_NEWNS in flags and current->fs hadn't been shared at all; in that case copy_mnt_ns() gets passed current->fs instead of a private copy, which causes interesting warts in proof of correctness] > I guess if private means fs->users == 1, the condition could still be true. Unfortunately, it's worse than just a convoluted proof of correctness. Consider the case when we have CLONE_NEWCGROUP in addition to CLONE_NEWNS (and current->fs->users == 1). We pass current->fs to copy_mnt_ns(), all right. Suppose it succeeds and flips current->fs->{pwd,root} to corresponding locations in the new namespace. Now we proceed to copy_cgroup_ns(), which fails (e.g. with -ENOMEM). We call put_mnt_ns() on the namespace created by copy_mnt_ns(), it's destroyed and its mount tree is dissolved, but... current->fs->root and current->fs->pwd are both left pointing to now detached mounts. They are pinning those, so it's not a UAF, but it leaves the calling process with unshare(2) failing with -ENOMEM _and_ leaving it with pwd and root on detached isolated mounts. The last part is clearly a bug. There is other fun related to that mess (races with pivot_root(), including the one between pivot_root() and fork(), of all things), but this one is easy to isolate and fix - treat CLONE_NEWNS as "allocate a new fs_struct even if it hadn't been shared in the first place". Sure, we could go for something like "if both CLONE_NEWNS *and* one of the things that might end up failing after copy_mnt_ns() call in create_new_namespaces() are set, force allocation of new fs_struct", but let's keep it simple - the cost of copy_fs_struct() is trivial. Another benefit is that copy_mnt_ns() with CLONE_NEWNS *always* gets a freshly allocated fs_struct, yet to be attached to anything. That seriously simplifies the analysis... FWIW, that bug had been there since the introduction of unshare(2) ;-/

In libslic3r/GCode/PostProcessor.cpp in Prusa PrusaSlicer through 2.6.1, a crafted 3mf project file can execute arbitrary code on a host where the project is sliced and G-code exported.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: 8822b: Avoid WARNING in rtw8822b_config_trx_mode() rtw8822b_set_antenna() can be called from userspace when the chip is powered off. In that case a WARNING is triggered in rtw8822b_config_trx_mode() because trying to read the RF registers when the chip is powered off returns an unexpected value. Call rtw8822b_config_trx_mode() in rtw8822b_set_antenna() only when the chip is powered on. ------------[ cut here ]------------ write RF mode table fail WARNING: CPU: 0 PID: 7183 at rtw8822b.c:824 rtw8822b_config_trx_mode.constprop.0+0x835/0x840 [rtw88_8822b] CPU: 0 UID: 0 PID: 7183 Comm: iw Tainted: G W OE 6.17.5-arch1-1 #1 PREEMPT(full) 01c39fc421df2af799dd5e9180b572af860b40c1 Tainted: [W]=WARN, [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: LENOVO 82KR/LNVNB161216, BIOS HBCN18WW 08/27/2021 RIP: 0010:rtw8822b_config_trx_mode.constprop.0+0x835/0x840 [rtw88_8822b] Call Trace: <TASK> rtw8822b_set_antenna+0x57/0x70 [rtw88_8822b 370206f42e5890d8d5f48eb358b759efa37c422b] rtw_ops_set_antenna+0x50/0x80 [rtw88_core 711c8fb4f686162be4625b1d0b8e8c6a5ac850fb] ieee80211_set_antenna+0x60/0x100 [mac80211 f1845d85d2ecacf3b71867635a050ece90486cf3] nl80211_set_wiphy+0x384/0xe00 [cfg80211 296485ee85696d2150309a6d21a7fbca83d3dbda] ? netdev_run_todo+0x63/0x550 genl_family_rcv_msg_doit+0xfc/0x160 genl_rcv_msg+0x1aa/0x2b0 ? __pfx_nl80211_pre_doit+0x10/0x10 [cfg80211 296485ee85696d2150309a6d21a7fbca83d3dbda] ? __pfx_nl80211_set_wiphy+0x10/0x10 [cfg80211 296485ee85696d2150309a6d21a7fbca83d3dbda] ? __pfx_nl80211_post_doit+0x10/0x10 [cfg80211 296485ee85696d2150309a6d21a7fbca83d3dbda] ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x59/0x110 genl_rcv+0x28/0x40 netlink_unicast+0x285/0x3c0 ? __alloc_skb+0xdb/0x1a0 netlink_sendmsg+0x20d/0x430 ____sys_sendmsg+0x39f/0x3d0 ? import_iovec+0x2f/0x40 ___sys_sendmsg+0x99/0xe0 ? refill_obj_stock+0x12e/0x240 __sys_sendmsg+0x8a/0xf0 do_syscall_64+0x81/0x970 ? do_syscall_64+0x81/0x970 ? ksys_read+0x73/0xf0 ? do_syscall_64+0x81/0x970 ? count_memcg_events+0xc2/0x190 ? handle_mm_fault+0x1d7/0x2d0 ? do_user_addr_fault+0x21a/0x690 ? exc_page_fault+0x7e/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: rapidio: replace rio_free_net() with kfree() in rio_scan_alloc_net() When idtab allocation fails, net is not registered with rio_add_net() yet, so kfree(net) is sufficient to release the memory. Set mport->net to NULL to avoid dangling pointer.

In the Linux kernel, the following vulnerability has been resolved: x86/apic: Disable x2apic on resume if the kernel expects so When resuming from s2ram, firmware may re-enable x2apic mode, which may have been disabled by the kernel during boot either because it doesn't support IRQ remapping or for other reasons. This causes the kernel to continue using the xapic interface, while the hardware is in x2apic mode, which causes hangs. This happens on defconfig + bare metal + s2ram. Fix this in lapic_resume() by disabling x2apic if the kernel expects it to be disabled, i.e. when x2apic_mode = 0. The ACPI v6.6 spec, Section 16.3 [1] says firmware restores either the pre-sleep configuration or initial boot configuration for each CPU, including MSR state: When executing from the power-on reset vector as a result of waking from an S2 or S3 sleep state, the platform firmware performs only the hardware initialization required to restore the system to either the state the platform was in prior to the initial operating system boot, or to the pre-sleep configuration state. In multiprocessor systems, non-boot processors should be placed in the same state as prior to the initial operating system boot. (further ahead) If this is an S2 or S3 wake, then the platform runtime firmware restores minimum context of the system before jumping to the waking vector. This includes: CPU configuration. Platform runtime firmware restores the pre-sleep configuration or initial boot configuration of each CPU (MSR, MTRR, firmware update, SMBase, and so on). Interrupts must be disabled (for IA-32 processors, disabled by CLI instruction). (and other things) So at least as per the spec, re-enablement of x2apic by the firmware is allowed if "x2apic on" is a part of the initial boot configuration. [1] https://uefi.org/specs/ACPI/6.6/16_Waking_and_Sleeping.html#initialization [ bp: Massage. ]

In the Linux kernel, the following vulnerability has been resolved: net: dsa: microchip: Fix error path in PTP IRQ setup If request_threaded_irq() fails during the PTP message IRQ setup, the newly created IRQ mapping is never disposed. Indeed, the ksz_ptp_irq_setup()'s error path only frees the mappings that were successfully set up. Dispose the newly created mapping if the associated request_threaded_irq() fails at setup.

In the Linux kernel, the following vulnerability has been resolved: nsfs: tighten permission checks for handle opening Even privileged services should not necessarily be able to see other privileged service's namespaces so they can't leak information to each other. Use may_see_all_namespaces() helper that centralizes this policy until the nstree adapts.

A Cross Site Scripting vulnerability in Alkacon OpenCms before 16 exists via updateModelGroups.jsp.

Prison Management System Using PHP v1.0 was discovered to contain a SQL injection vulnerability via the username on the Admin login page.

nanoMODBUS through v1.22.0 has a stack-based buffer overflow in recv_read_registers_res() in nanomodbus.c. When a client calls nmbs_read_holding_registers() or nmbs_read_input_registers(), the library writes register data from the server response to the caller-provided buffer based on the response's byte_count field before validating that byte_count matches the requested quantity. A malicious Modbus TCP server can send a response with byte_count=250 (125 registers) regardless of the requested quantity, causing up to 248 bytes of attacker-controlled data to overflow the buffer, potentially allowing remote code execution.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix dsc eDP issue [why] Need to add function hook check before use

In the Linux kernel, the following vulnerability has been resolved: drm/i915: Fix potential overflow of shmem scatterlist length When a scatterlists table of a GEM shmem object of size 4 GB or more is populated with pages allocated from a folio, unsigned int .length attribute of a scatterlist may get overflowed if total byte length of pages allocated to that single scatterlist happens to reach or cross the 4GB limit. As a consequence, users of the object may suffer from hitting unexpected, premature end of the object's backing pages. [278.780187] ------------[ cut here ]------------ [278.780377] WARNING: CPU: 1 PID: 2326 at drivers/gpu/drm/i915/i915_mm.c:55 remap_sg+0x199/0x1d0 [i915] ... [278.780654] CPU: 1 UID: 0 PID: 2326 Comm: gem_mmap_offset Tainted: G S U 6.17.0-rc1-CI_DRM_16981-ged823aaa0607+ #1 PREEMPT(voluntary) [278.780656] Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER [278.780658] Hardware name: Intel Corporation Meteor Lake Client Platform/MTL-P LP5x T3 RVP, BIOS MTLPFWI1.R00.3471.D91.2401310918 01/31/2024 [278.780659] RIP: 0010:remap_sg+0x199/0x1d0 [i915] ... [278.780786] Call Trace: [278.780787] <TASK> [278.780788] ? __apply_to_page_range+0x3e6/0x910 [278.780795] ? __pfx_remap_sg+0x10/0x10 [i915] [278.780906] apply_to_page_range+0x14/0x30 [278.780908] remap_io_sg+0x14d/0x260 [i915] [278.781013] vm_fault_cpu+0xd2/0x330 [i915] [278.781137] __do_fault+0x3a/0x1b0 [278.781140] do_fault+0x322/0x640 [278.781143] __handle_mm_fault+0x938/0xfd0 [278.781150] handle_mm_fault+0x12c/0x300 [278.781152] ? lock_mm_and_find_vma+0x4b/0x760 [278.781155] do_user_addr_fault+0x2d6/0x8e0 [278.781160] exc_page_fault+0x96/0x2c0 [278.781165] asm_exc_page_fault+0x27/0x30 ... That issue was apprehended by the author of a change that introduced it, and potential risk even annotated with a comment, but then never addressed. When adding folio pages to a scatterlist table, take care of byte length of any single scatterlist not exceeding max_segment. (cherry picked from commit 06249b4e691a75694c014a61708c007fb5755f60)

In the Linux kernel, the following vulnerability has been resolved: mm: memfd_luo: always dirty all folios A dirty folio is one which has been written to. A clean folio is its opposite. Since a clean folio has no user data, it can be freed under memory pressure. memfd preservation with LUO saves the flag at preserve(). This is problematic. The folio might get dirtied later. Saving it at freeze() also doesn't work, since the dirty bit from PTE is normally synced at unmap and there might still be mappings of the file at freeze(). To see why this is a problem, say a folio is clean at preserve, but gets dirtied later. The serialized state of the folio will mark it as clean. After retrieve, the next kernel will see the folio as clean and might try to reclaim it under memory pressure. This will result in losing user data. Mark all folios of the file as dirty, and always set the MEMFD_LUO_FOLIO_DIRTY flag. This comes with the side effect of making all clean folios un-reclaimable. This is a cost that has to be paid for participants of live update. It is not expected to be a common use case to preserve a lot of clean folios anyway. Since the value of pfolio->flags is a constant now, drop the flags variable and set it directly.

LINQPad before 5.52.01 Pro edition is vulnerable to Unsafe Deserialization in LINQPad.AutoRefManager::PopulateFromCache(), leading to code execution.

A SSTI (server side template injection) vulnerability in the custom template export function in yeti-platform yeti before 2.1.12 allows attackers to execute code on the application server.

In the Linux kernel, the following vulnerability has been resolved: rust_binder: check ownership before using vma When installing missing pages (or zapping them), Rust Binder will look up the vma in the mm by address, and then call vm_insert_page (or zap_page_range_single). However, if the vma is closed and replaced with a different vma at the same address, this can lead to Rust Binder installing pages into the wrong vma. By installing the page into a writable vma, it becomes possible to write to your own binder pages, which are normally read-only. Although you're not supposed to be able to write to those pages, the intent behind the design of Rust Binder is that even if you get that ability, it should not lead to anything bad. Unfortunately, due to another bug, that is not the case. To fix this, store a pointer in vm_private_data and check that the vma returned by vma_lookup() has the right vm_ops and vm_private_data before trying to use the vma. This should ensure that Rust Binder will refuse to interact with any other VMA. The plan is to introduce more vma abstractions to avoid this unsafe access to vm_ops and vm_private_data, but for now let's start with the simplest possible fix. C Binder performs the same check in a slightly different way: it provides a vm_ops->close that sets a boolean to true, then checks that boolean after calling vma_lookup(), but this is more fragile than the solution in this patch. (We probably still want to do both, but the vm_ops->close callback will be added later as part of the follow-up vma API changes.) It's still possible to remap the vma so that pages appear in the right vma, but at the wrong offset, but this is a separate issue and will be fixed when Rust Binder gets a vm_ops->close callback.

In the Linux kernel, the following vulnerability has been resolved: rust_binder: avoid reading the written value in offsets array When sending a transaction, its offsets array is first copied into the target proc's vma, and then the values are read back from there. This is normally fine because the vma is a read-only mapping, so the target process cannot change the value under us. However, if the target process somehow gains the ability to write to its own vma, it could change the offset before it's read back, causing the kernel to misinterpret what the sender meant. If the sender happens to send a payload with a specific shape, this could in the worst case lead to the receiver being able to privilege escalate into the sender. The intent is that gaining the ability to change the read-only vma of your own process should not be exploitable, so remove this TOCTOU read even though it's unexploitable without another Binder bug.

In the Linux kernel, the following vulnerability has been resolved: sched/mmcid: Handle vfork()/CLONE_VM correctly Matthieu and Jiri reported stalls where a task endlessly loops in mm_get_cid() when scheduling in. It turned out that the logic which handles vfork()'ed tasks is broken. It is invoked when the number of tasks associated to a process is smaller than the number of MMCID users. It then walks the task list to find the vfork()'ed task, but accounts all the already processed tasks as well. If that double processing brings the number of to be handled tasks to 0, the walk stops and the vfork()'ed task's CID is not fixed up. As a consequence a subsequent schedule in fails to acquire a (transitional) CID and the machine stalls. Cure this by removing the accounting condition and make the fixup always walk the full task list if it could not find the exact number of users in the process' thread list.

A security vulnerability has been detected in SourceCodester Pizzafy Ecommerce System 1.0. This issue affects some unknown processing of the file /admin/index.php. Such manipulation of the argument page leads to cross site scripting. The attack may be launched remotely. The exploit has been disclosed publicly and may be used.

A weakness has been identified in huangjunsen0406 xiaozhi-mcphub up to 1.0.3. This vulnerability affects unknown code of the file src/controllers/dxtController.ts. This manipulation of the argument manifest.name causes path traversal. The attack may be initiated remotely. The exploit has been made available to the public and could be used for attacks. The project was informed of the problem early through an issue report but has not responded yet.

A security flaw has been discovered in gyoridavid short-video-maker up to 1.3.4. This affects an unknown part of the file src/server/routers/rest.ts of the component REST API. The manipulation of the argument req.params.tmpFile results in path traversal. The attack can be launched remotely. The exploit has been released to the public and may be used for attacks. The project was informed of the problem early through an issue report but has not responded yet.

This vulnerability, in the MAXHUB Pivot client application versions prior to v1.36.2, may allow an attacker to obtain encrypted tenant email addresses and related metadata from any tenant. Due to the presence of a hardcoded AES key within the application, the encrypted data can be decrypted, enabling access to tenant email addresses and associated information in cleartext. Furthermore, an attacker may be able to cause a denial-of-service condition by enrolling multiple unauthorized devices into a tenant via MQTT, potentially disrupting tenant operations.

Argo CD is a declarative, GitOps continuous delivery tool for Kubernetes. From versions 3.2.0 to before 3.2.11 and 3.3.0 to before 3.3.9, there is a missing authorization and data-masking gap in Argo CD's ServerSideDiff endpoint that allows an attacker with read-only access to extract plaintext Kubernetes Secret data from etcd via the Kubernetes API server's Server-Side Apply dry-run mechanism. This issue has been patched in versions 3.2.11 and 3.3.9.

A vulnerability was identified in JeecgBoot up to 3.9.1. Affected by this issue is some unknown functionality of the file /sys/dict/loadTreeData of the component JSON Object Handler. The manipulation of the argument condition leads to sql injection. The attack can be initiated remotely. The exploit is publicly available and might be used. The vendor confirms (translated from Chinese): "It should have been fixed; a batch of issues were recently resolved."

A reflected HTML injection vulnerability was identified in the GitHub Enterprise Server Management Console login page that could allow credential theft. The redirect_to query parameter on the /setup/unlock endpoint was reflected into an HTML attribute without proper sanitization, enabling an attacker to inject a form element that could capture administrator credentials. Exploitation required an administrator to click a crafted link and enter their credentials. This vulnerability affected GitHub Enterprise Server versions 3.19.1 through 3.19.5 and 3.20.0 through 3.20.1, and was fixed in versions 3.19.6 and 3.20.2. This vulnerability was reported via the GitHub Bug Bounty program.

A server-side request forgery (SSRF) vulnerability was identified in the GitHub Enterprise Server notebook viewer that allowed an attacker to access internal services by exploiting URL parser confusion between the validation layer and the HTTP request library. The hostname validation used a different URL parser than the request library, enabling a crafted URL to pass validation while directing the request to an unintended host. Exploitation required network access to the GitHub Enterprise Server instance. This vulnerability affected all versions of GitHub Enterprise Server prior to 3.21 and was fixed in versions 3.16.18, 3.17.15, 3.18.9, 3.19.6, and 3.20.2. This vulnerability was reported via the GitHub Bug Bounty program.

A denial of service vulnerability was identified in GitHub Enterprise Server that allowed an unauthenticated attacker to cause service disruption by sending crafted requests with deeply nested JSON payloads to an unauthenticated API endpoint. The endpoint parsed user-controlled JSON request bodies without size or depth limits, causing excessive CPU and memory consumption. This vulnerability affected all versions of GitHub Enterprise Server prior to 3.21 and was fixed in versions 3.20.2, 3.19.6, 3.18.9, 3.17.15, and 3.16.18. This vulnerability was reported via the GitHub Bug Bounty program.

A vulnerability was determined in 8421bit MiniClaw up to 43905b934cf76489ab28e4d17da28ee97970f91f. Affected by this vulnerability is the function isPathInside of the file src/kernel.ts of the component executeSkillScript. Executing a manipulation can lead to path traversal. It is possible to launch the attack remotely. The exploit has been publicly disclosed and may be utilized. This product takes the approach of rolling releases to provide continious delivery. Therefore, version details for affected and updated releases are not available. This patch is called e8bd4e17e9428260f2161378356affc5ce90d6ed. It is advisable to implement a patch to correct this issue.

An authentication bypass vulnerability was identified in GitHub Enterprise Server that allowed an unauthenticated attacker to create a local user account, bypassing the configured external identity provider. When external authentication was enabled, the signup endpoint did not properly enforce the authentication restriction, allowing account creation and session establishment without identity provider validation. The created account was limited to the default base permissions configured on the instance. Exploitation required network access to a GHES instance configured with an external authentication provider. This vulnerability affected all versions of GitHub Enterprise Server prior to 3.21 and was fixed in versions 3.20.2, 3.19.6, 3.18.9, 3.17.15, and 3.16.18.

Vvveb before 1.0.8.2 contains an information disclosure vulnerability in the cron controller that allows unauthenticated attackers to retrieve the application's secret cron key. Attackers can access the cron controller without authentication and retrieve the exposed secret key from the response, enabling them to trigger scheduled task execution outside of the intended schedule.