CVE Feed

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Fix race condition during PASID entry replacement The Intel VT-d PASID table entry is 512 bits (64 bytes). When replacing an active PASID entry (e.g., during domain replacement), the current implementation calculates a new entry on the stack and copies it to the table using a single structure assignment. struct pasid_entry *pte, new_pte; pte = intel_pasid_get_entry(dev, pasid); pasid_pte_config_first_level(iommu, &new_pte, ...); *pte = new_pte; Because the hardware may fetch the 512-bit PASID entry in multiple 128-bit chunks, updating the entire entry while it is active (Present bit set) risks a "torn" read. In this scenario, the IOMMU hardware could observe an inconsistent state — partially new data and partially old data — leading to unpredictable behavior or spurious faults. Fix this by removing the unsafe "replace" helpers and following the "clear-then-update" flow, which ensures the Present bit is cleared and the required invalidation handshake is completed before the new configuration is applied.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix memory leak in amdgpu_acpi_enumerate_xcc() In amdgpu_acpi_enumerate_xcc(), if amdgpu_acpi_dev_init() returns -ENOMEM, the function returns directly without releasing the allocated xcc_info, resulting in a memory leak. Fix this by ensuring that xcc_info is properly freed in the error paths. Compile tested only. Issue found using a prototype static analysis tool and code review.

In the Linux kernel, the following vulnerability has been resolved: crypto: starfive - Fix memory leak in starfive_aes_aead_do_one_req() The starfive_aes_aead_do_one_req() function allocates rctx->adata with kzalloc() but fails to free it if sg_copy_to_buffer() or starfive_aes_hw_init() fails, which lead to memory leaks. Since rctx->adata is unconditionally freed after the write_adata operations, ensure consistent cleanup by freeing the allocation in these earlier error paths as well. Compile tested only. Issue found using a prototype static analysis tool and code review.

In the Linux kernel, the following vulnerability has been resolved: md/raid5: fix IO hang with degraded array with llbitmap When llbitmap bit state is still unwritten, any new write should force rcw, as bitmap_ops->blocks_synced() is checked in handle_stripe_dirtying(). However, later the same check is missing in need_this_block(), causing stripe to deadloop during handling because handle_stripe() will decide to go to handle_stripe_fill(), meanwhile need_this_block() always return 0 and nothing is handled.

In the Linux kernel, the following vulnerability has been resolved: bpf: Return proper address for non-zero offsets in insn array The map_direct_value_addr() function of the instruction array map incorrectly adds offset to the resulting address. This is a bug, because later the resolve_pseudo_ldimm64() function adds the offset. Fix it. Corresponding selftests are added in a consequent commit.

In the Linux kernel, the following vulnerability has been resolved: cpuidle: Skip governor when only one idle state is available On certain platforms (PowerNV systems without a power-mgt DT node), cpuidle may register only a single idle state. In cases where that single state is a polling state (state 0), the ladder governor may incorrectly treat state 1 as the first usable state and pass an out-of-bounds index. This can lead to a NULL enter callback being invoked, ultimately resulting in a system crash. [ 13.342636] cpuidle-powernv : Only Snooze is available [ 13.351854] Faulting instruction address: 0x00000000 [ 13.376489] NIP [0000000000000000] 0x0 [ 13.378351] LR [c000000001e01974] cpuidle_enter_state+0x2c4/0x668 Fix this by adding a bail-out in cpuidle_select() that returns state 0 directly when state_count <= 1, bypassing the governor and keeping the tick running.

In the Linux kernel, the following vulnerability has been resolved: HID: playstation: Add missing check for input_ff_create_memless The ps_gamepad_create() function calls input_ff_create_memless() without verifying its return value, which can lead to incorrect behavior or potential crashes when FF effects are triggered. Add a check for the return value of input_ff_create_memless().

In the Linux kernel, the following vulnerability has been resolved: ublk: use READ_ONCE() to read struct ublksrv_ctrl_cmd struct ublksrv_ctrl_cmd is part of the io_uring_sqe, which may lie in userspace-mapped memory. It's racy to access its fields with normal loads, as userspace may write to them concurrently. Use READ_ONCE() to copy the ublksrv_ctrl_cmd from the io_uring_sqe to the stack. Use the local copy in place of the one in the io_uring_sqe.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix memory leak in amdgpu_ras_init() When amdgpu_nbio_ras_sw_init() fails in amdgpu_ras_init(), the function returns directly without freeing the allocated con structure, leading to a memory leak. Fix this by jumping to the release_con label to properly clean up the allocated memory before returning the error code. Compile tested only. Issue found using a prototype static analysis tool and code review.

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Stop job scheduling across aie2_release_resource() Running jobs on a hardware context while it is in the process of releasing resources can lead to use-after-free and crashes. Fix this by stopping job scheduling before calling aie2_release_resource() and restarting it after the release completes. Additionally, aie2_sched_job_run() now checks whether the hardware context is still active.

In the Linux kernel, the following vulnerability has been resolved: crypto: ccree - fix a memory leak in cc_mac_digest() Add cc_unmap_result() if cc_map_hash_request_final() fails to prevent potential memory leak.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix re-decryption of RESPONSE packets If a RESPONSE packet gets a temporary failure during processing, it may end up in a partially decrypted state - and then get requeued for a retry. Fix this by just discarding the packet; we will send another CHALLENGE packet and thereby elicit a further response. Similarly, discard an incoming CHALLENGE packet if we get an error whilst generating a RESPONSE; the server will send another CHALLENGE.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Initialize new folios before use KMSAN reports an uninitialized value in longest_match_std(), invoked from ntfs_compress_write(). When new folios are allocated without being marked uptodate and ni_read_frame() is skipped because the caller expects the frame to be completely overwritten, some reserved folios may remain only partially filled, leaving the rest memory uninitialized.

Northern.tech Mender Server v4.1.0, v4.0.1 and below, and fixed in v4.1.1 and v4.0.2 allows Directory Traversal.

Use after free in WebCodecs in Google Chrome prior to 148.0.7778.216 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted HTML page. (Chromium security severity: High)

A stored cross-site scripting (XSS) vulnerability in the /admin/config-module.php component of creatorsofcode simplephp GitHub commit 5184cff (Latest as of 2026-02-27) via injecting a crafted payload.

In the Linux kernel, the following vulnerability has been resolved: power: supply: act8945a: Fix use-after-free in power_supply_changed() Using the `devm_` variant for requesting IRQ _before_ the `devm_` variant for allocating/registering the `power_supply` handle, means that the `power_supply` handle will be deallocated/unregistered _before_ the interrupt handler (since `devm_` naturally deallocates in reverse allocation order). This means that during removal, there is a race condition where an interrupt can fire just _after_ the `power_supply` handle has been freed, *but* just _before_ the corresponding unregistration of the IRQ handler has run. This will lead to the IRQ handler calling `power_supply_changed()` with a freed `power_supply` handle. Which usually crashes the system or otherwise silently corrupts the memory... Note that there is a similar situation which can also happen during `probe()`; the possibility of an interrupt firing _before_ registering the `power_supply` handle. This would then lead to the nasty situation of using the `power_supply` handle *uninitialized* in `power_supply_changed()`. Fix this racy use-after-free by making sure the IRQ is requested _after_ the registration of the `power_supply` handle.

In the Linux kernel, the following vulnerability has been resolved: power: supply: wm97xx: Fix NULL pointer dereference in power_supply_changed() In `probe()`, `request_irq()` is called before allocating/registering a `power_supply` handle. If an interrupt is fired between the call to `request_irq()` and `power_supply_register()`, the `power_supply` handle will be used uninitialized in `power_supply_changed()` in `wm97xx_bat_update()` (triggered from the interrupt handler). This will lead to a `NULL` pointer dereference since Fix this racy `NULL` pointer dereference by making sure the IRQ is requested _after_ the registration of the `power_supply` handle. Since the IRQ is the last thing requests in the `probe()` now, remove the error path for freeing it. Instead add one for unregistering the `power_supply` handle when IRQ request fails.

In the Linux kernel, the following vulnerability has been resolved: tpm: st33zp24: Fix missing cleanup on get_burstcount() error get_burstcount() can return -EBUSY on timeout. When this happens, st33zp24_send() returns directly without releasing the locality acquired earlier. Use goto out_err to ensure proper cleanup when get_burstcount() fails.

In the Linux kernel, the following vulnerability has been resolved: scsi: smartpqi: Fix memory leak in pqi_report_phys_luns() pqi_report_phys_luns() fails to release the rpl_list buffer when encountering an unsupported data format or when the allocation for rpl_16byte_wwid_list fails. These early returns bypass the cleanup logic, leading to memory leaks. Consolidate the error handling by adding an out_free_rpl_list label and use goto statements to ensure rpl_list is consistently freed on failure. Compile tested only. Issue found using a prototype static analysis tool and code review.

In the Linux kernel, the following vulnerability has been resolved: phy: freescale: imx8qm-hsio: fix NULL pointer dereference During the probe the refclk_pad pointer is set to NULL if the 'fsl,refclk-pad-mode' property is not defined in the devicetree node. But in imx_hsio_configure_clk_pad() this pointer is unconditionally used which could result in a NULL pointer dereference. So check the pointer before to use it.

In the Linux kernel, the following vulnerability has been resolved: HID: intel-ish-hid: fix NULL-ptr-deref in ishtp_bus_remove_all_clients During a warm reset flow, the cl->device pointer may be NULL if the reset occurs while clients are still being enumerated. Accessing cl->device->reference_count without a NULL check leads to a kernel panic. This issue was identified during multi-unit warm reboot stress clycles. Add a defensive NULL check for cl->device to ensure stability under such intensive testing conditions. KASAN: null-ptr-deref in range [0000000000000000-0000000000000007] Workqueue: ish_fw_update_wq fw_reset_work_fn Call Trace: ishtp_bus_remove_all_clients+0xbe/0x130 [intel_ishtp] ishtp_reset_handler+0x85/0x1a0 [intel_ishtp] fw_reset_work_fn+0x8a/0xc0 [intel_ish_ipc]

In the Linux kernel, the following vulnerability has been resolved: crypto: inside-secure/eip93 - unregister only available algorithm EIP93 has an options register. This register indicates which crypto algorithms are implemented in silicon. Supported algorithms are registered on this basis. Unregister algorithms on the same basis. Currently, all algorithms are unregistered, even those not supported by HW. This results in panic on platforms that don't have all options implemented in silicon.

In the Linux kernel, the following vulnerability has been resolved: PCI/P2PDMA: Release per-CPU pgmap ref when vm_insert_page() fails When vm_insert_page() fails in p2pmem_alloc_mmap(), p2pmem_alloc_mmap() doesn't invoke percpu_ref_put() to free the per-CPU ref of pgmap acquired after gen_pool_alloc_owner(), and memunmap_pages() will hang forever when trying to remove the PCI device. Fix it by adding the missed percpu_ref_put().

In the Linux kernel, the following vulnerability has been resolved: power: supply: pm8916_bms_vm: Fix use-after-free in power_supply_changed() Using the `devm_` variant for requesting IRQ _before_ the `devm_` variant for allocating/registering the `power_supply` handle, means that the `power_supply` handle will be deallocated/unregistered _before_ the interrupt handler (since `devm_` naturally deallocates in reverse allocation order). This means that during removal, there is a race condition where an interrupt can fire just _after_ the `power_supply` handle has been freed, *but* just _before_ the corresponding unregistration of the IRQ handler has run. This will lead to the IRQ handler calling `power_supply_changed()` with a freed `power_supply` handle. Which usually crashes the system or otherwise silently corrupts the memory... Note that there is a similar situation which can also happen during `probe()`; the possibility of an interrupt firing _before_ registering the `power_supply` handle. This would then lead to the nasty situation of using the `power_supply` handle *uninitialized* in `power_supply_changed()`. Fix this racy use-after-free by making sure the IRQ is requested _after_ the registration of the `power_supply` handle.

In the Linux kernel, the following vulnerability has been resolved: powerpc/eeh: fix recursive pci_lock_rescan_remove locking in EEH event handling The recent commit 1010b4c012b0 ("powerpc/eeh: Make EEH driver device hotplug safe") restructured the EEH driver to improve synchronization with the PCI hotplug layer. However, it inadvertently moved pci_lock_rescan_remove() outside its intended scope in eeh_handle_normal_event(), leading to broken PCI error reporting and improper EEH event triggering. Specifically, eeh_handle_normal_event() acquired pci_lock_rescan_remove() before calling eeh_pe_bus_get(), but eeh_pe_bus_get() itself attempts to acquire the same lock internally, causing nested locking and disrupting normal EEH event handling paths. This patch adds a boolean parameter do_lock to _eeh_pe_bus_get(), with two public wrappers: eeh_pe_bus_get() with locking enabled. eeh_pe_bus_get_nolock() that skips locking. Callers that already hold pci_lock_rescan_remove() now use eeh_pe_bus_get_nolock() to avoid recursive lock acquisition. Additionally, pci_lock_rescan_remove() calls are restored to the correct position—after eeh_pe_bus_get() and immediately before iterating affected PEs and devices. This ensures EEH-triggered PCI removes occur under proper bus rescan locking without recursive lock contention. The eeh_pe_loc_get() function has been split into two functions: eeh_pe_loc_get(struct eeh_pe *pe) which retrieves the loc for given PE. eeh_pe_loc_get_bus(struct pci_bus *bus) which retrieves the location code for given bus. This resolves lockdep warnings such as: <snip> [ 84.964298] [ T928] ============================================ [ 84.964304] [ T928] WARNING: possible recursive locking detected [ 84.964311] [ T928] 6.18.0-rc3 #51 Not tainted [ 84.964315] [ T928] -------------------------------------------- [ 84.964320] [ T928] eehd/928 is trying to acquire lock: [ 84.964324] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40 [ 84.964342] [ T928] but task is already holding lock: [ 84.964347] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40 [ 84.964357] [ T928] other info that might help us debug this: [ 84.964363] [ T928] Possible unsafe locking scenario: [ 84.964367] [ T928] CPU0 [ 84.964370] [ T928] ---- [ 84.964373] [ T928] lock(pci_rescan_remove_lock); [ 84.964378] [ T928] lock(pci_rescan_remove_lock); [ 84.964383] [ T928] *** DEADLOCK *** [ 84.964388] [ T928] May be due to missing lock nesting notation [ 84.964393] [ T928] 1 lock held by eehd/928: [ 84.964397] [ T928] #0: c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40 [ 84.964408] [ T928] stack backtrace: [ 84.964414] [ T928] CPU: 2 UID: 0 PID: 928 Comm: eehd Not tainted 6.18.0-rc3 #51 VOLUNTARY [ 84.964417] [ T928] Hardware name: IBM,9080-HEX POWER10 (architected) 0x800200 0xf000006 of:IBM,FW1060.00 (NH1060_022) hv:phyp pSeries [ 84.964419] [ T928] Call Trace: [ 84.964420] [ T928] [c0000011a7157990] [c000000001705de4] dump_stack_lvl+0xc8/0x130 (unreliable) [ 84.964424] [ T928] [c0000011a71579d0] [c0000000002f66e0] print_deadlock_bug+0x430/0x440 [ 84.964428] [ T928] [c0000011a7157a70] [c0000000002fd0c0] __lock_acquire+0x1530/0x2d80 [ 84.964431] [ T928] [c0000011a7157ba0] [c0000000002fea54] lock_acquire+0x144/0x410 [ 84.964433] [ T928] [c0000011a7157cb0] [c0000011a7157cb0] __mutex_lock+0xf4/0x1050 [ 84.964436] [ T928] [c0000011a7157e00] [c000000000de21d8] pci_lock_rescan_remove+0x28/0x40 [ 84.964439] [ T928] [c0000011a7157e20] [c00000000004ed98] eeh_pe_bus_get+0x48/0xc0 [ 84.964442] [ T928] [c0000011a7157e50] [c00000 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: power: supply: pf1550: Fix use-after-free in power_supply_changed() Using the `devm_` variant for requesting IRQ _before_ the `devm_` variant for allocating/registering the `power_supply` handle, means that the `power_supply` handle will be deallocated/unregistered _before_ the interrupt handler (since `devm_` naturally deallocates in reverse allocation order). This means that during removal, there is a race condition where an interrupt can fire just _after_ the `power_supply` handle has been freed, *but* just _before_ the corresponding unregistration of the IRQ handler has run. This will lead to the IRQ handler calling `power_supply_changed()` with a freed `power_supply` handle. Which usually crashes the system or otherwise silently corrupts the memory... Note that there is a similar situation which can also happen during `probe()`; the possibility of an interrupt firing _before_ registering the `power_supply` handle. This would then lead to the nasty situation of using the `power_supply` handle *uninitialized* in `power_supply_changed()`. Fix this racy use-after-free by making sure the IRQ is requested _after_ the registration of the `power_supply` handle.

In the Linux kernel, the following vulnerability has been resolved: Revert "hwmon: (ibmpex) fix use-after-free in high/low store" This reverts commit 6946c726c3f4c36f0f049e6f97e88c510b15f65d. Jean Delvare points out that the patch does not completely fix the reported problem, that it in fact introduces a (new) race condition, and that it may actually not be needed in the first place. Various AI reviews agree. Specific and relevant AI feedback: " This reordering sets the driver data to NULL before removing the sensor attributes in the loop below. ibmpex_show_sensor() retrieves this driver data via dev_get_drvdata() but does not check if it is NULL before dereferencing it to access data->sensors[]. If a userspace process reads a sensor file (like temp1_input) while this delete function is running, could it race with the dev_set_drvdata(..., NULL) call here and crash in ibmpex_show_sensor()? Would it be safer to keep the original order where device_remove_file() is called before clearing the driver data? device_remove_file() should wait for any active sysfs callbacks to complete, which might already prevent the use-after-free this patch intends to fix. " Revert the offending patch. If it can be shown that the originally reported alleged race condition does indeed exist, it can always be re-introduced with a complete fix.

In the Linux kernel, the following vulnerability has been resolved: sched/rt: Skip currently executing CPU in rto_next_cpu() CPU0 becomes overloaded when hosting a CPU-bound RT task, a non-CPU-bound RT task, and a CFS task stuck in kernel space. When other CPUs switch from RT to non-RT tasks, RT load balancing (LB) is triggered; with HAVE_RT_PUSH_IPI enabled, they send IPIs to CPU0 to drive the execution of rto_push_irq_work_func. During push_rt_task on CPU0, if next_task->prio < rq->donor->prio, resched_curr() sets NEED_RESCHED and after the push operation completes, CPU0 calls rto_next_cpu(). Since only CPU0 is overloaded in this scenario, rto_next_cpu() should ideally return -1 (no further IPI needed). However, multiple CPUs invoking tell_cpu_to_push() during LB increments rd->rto_loop_next. Even when rd->rto_cpu is set to -1, the mismatch between rd->rto_loop and rd->rto_loop_next forces rto_next_cpu() to restart its search from -1. With CPU0 remaining overloaded (satisfying rt_nr_migratory && rt_nr_total > 1), it gets reselected, causing CPU0 to queue irq_work to itself and send self-IPIs repeatedly. As long as CPU0 stays overloaded and other CPUs run pull_rt_tasks(), it falls into an infinite self-IPI loop, which triggers a CPU hardlockup due to continuous self-interrupts. The trigging scenario is as follows: cpu0 cpu1 cpu2 pull_rt_task tell_cpu_to_push <------------irq_work_queue_on rto_push_irq_work_func push_rt_task resched_curr(rq) pull_rt_task rto_next_cpu tell_cpu_to_push <-------------------------- atomic_inc(rto_loop_next) rd->rto_loop != next rto_next_cpu irq_work_queue_on rto_push_irq_work_func Fix redundant self-IPI by filtering the initiating CPU in rto_next_cpu(). This solution has been verified to effectively eliminate spurious self-IPIs and prevent CPU hardlockup scenarios.

In the Linux kernel, the following vulnerability has been resolved: mtd: parsers: Fix memory leak in mtd_parser_tplink_safeloader_parse() The function mtd_parser_tplink_safeloader_parse() allocates buf via mtd_parser_tplink_safeloader_read_table(). If the allocation for parts[idx].name fails inside the loop, the code jumps to the err_free label without freeing buf, leading to a memory leak. Fix this by freeing the temporary buffer buf in the err_free label. Compile tested only. Issue found using a prototype static analysis tool and code review.

In the Linux kernel, the following vulnerability has been resolved: power: supply: pm8916_lbc: Fix use-after-free in power_supply_changed() Using the `devm_` variant for requesting IRQ _before_ the `devm_` variant for allocating/registering the `power_supply` handle, means that the `power_supply` handle will be deallocated/unregistered _before_ the interrupt handler (since `devm_` naturally deallocates in reverse allocation order). This means that during removal, there is a race condition where an interrupt can fire just _after_ the `power_supply` handle has been freed, *but* just _before_ the corresponding unregistration of the IRQ handler has run. This will lead to the IRQ handler calling `power_supply_changed()` with a freed `power_supply` handle. Which usually crashes the system or otherwise silently corrupts the memory... Note that there is a similar situation which can also happen during `probe()`; the possibility of an interrupt firing _before_ registering the `power_supply` handle. This would then lead to the nasty situation of using the `power_supply` handle *uninitialized* in `power_supply_changed()`. Fix this racy use-after-free by making sure the IRQ is requested _after_ the registration of the `power_supply` handle.

In the Linux kernel, the following vulnerability has been resolved: tpm: tpm_i2c_infineon: Fix locality leak on get_burstcount() failure get_burstcount() can return -EBUSY on timeout. When this happens, the function returns directly without releasing the locality that was acquired at the beginning of tpm_tis_i2c_send(). Use goto out_err to ensure proper cleanup when get_burstcount() fails.

An issue in Dolibarr ERP/CRM v.22.0.0 through v.22.0.4 and v.24.0.0-alpha allows a remote attacker to execute arbitrary code via the htdocs/cron/class/cronjob.class.php, call_user_func_array() in function job type

In the Linux kernel, the following vulnerability has been resolved: bpf: Limit bpf program signature size Practical BPF signatures are significantly smaller than KMALLOC_MAX_CACHE_SIZE Allowing larger sizes opens the door for abuse by passing excessive size values and forcing the kernel into expensive allocation paths (via kmalloc_large or vmalloc).

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix potential UAF and double free in smb2_open_file() Zero out @err_iov and @err_buftype before retrying SMB2_open() to prevent an UAF bug if @data != NULL, otherwise a double free.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix slab-use-after-free in qd_put Commit a475c5dd16e5 ("gfs2: Free quota data objects synchronously") started freeing quota data objects during filesystem shutdown instead of putting them back onto the LRU list, but it failed to remove these objects from the LRU list, causing LRU list corruption. This caused use-after-free when the shrinker (gfs2_qd_shrink_scan) tried to access already-freed objects on the LRU list. Fix this by removing qd objects from the LRU list before freeing them in qd_put(). Initial fix from Deepanshu Kartikey <[email protected]>.

A NULL pointer dereference in GPAC MP4Box: when parsing certain truncated MP4 files, an unknown/invalid stsd entry can result in missing descriptor fields (e.g., codec/mime/profile strings). gf_media_map_esd then calls strlen() on a NULL pointer, triggering a crash (ASan SEGV).

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Fix race condition when checking rpm_on When autosuspend is triggered, driver rpm_on flag is set to indicate that a suspend/resume is already in progress. However, when a userspace application submits a command during this narrow window, amdxdna_pm_resume_get() may incorrectly skip the resume operation because the rpm_on flag is still set. This results in commands being submitted while the device has not actually resumed, causing unexpected behavior. The set_dpm() is called by suspend/resume, it relied on rpm_on flag to avoid calling into rpm suspend/resume recursivly. So to fix this, remove the use of the rpm_on flag entirely. Instead, introduce aie2_pm_set_dpm() which explicitly resumes the device before invoking set_dpm(). With this change, set_dpm() is called directly inside the suspend or resume execution path. Otherwise, aie2_pm_set_dpm() is called.

In the Linux kernel, the following vulnerability has been resolved: drm/panthor: Fix NULL pointer dereference on panthor_fw_unplug This patch removes the MCU halt and wait for halt procedures during panthor_fw_unplug() as the MCU can be in a variety of states or the FW may not even be loaded/initialized at all, the latter of which can lead to a NULL pointer dereference. It should be safe on unplug to just disable the MCU without waiting for it to halt as it may not be able to.

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Fix potential NULL pointer dereference in context cleanup aie_destroy_context() is invoked during error handling in aie2_create_context(). However, aie_destroy_context() assumes that the context's mailbox channel pointer is non-NULL. If mailbox channel creation fails, the pointer remains NULL and calling aie_destroy_context() can lead to a NULL pointer dereference. In aie2_create_context(), replace aie_destroy_context() with a function which request firmware to remove the context created previously.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: fix deadlock in ni_read_folio_cmpr Syzbot reported a task hung in ni_readpage_cmpr (now ni_read_folio_cmpr). This is caused by a lock inversion deadlock involving the inode mutex (ni_lock) and page locks. Scenario: 1. Task A enters ntfs_read_folio() for page X. It acquires ni_lock. 2. Task A calls ni_read_folio_cmpr(), which attempts to lock all pages in the compressed frame (including page Y). 3. Concurrently, Task B (e.g., via readahead) has locked page Y and calls ntfs_read_folio(). 4. Task B waits for ni_lock (held by A). 5. Task A waits for page Y lock (held by B). -> DEADLOCK. The fix is to restructure locking: do not take ni_lock in ntfs_read_folio(). Instead, acquire ni_lock inside ni_read_folio_cmpr() ONLY AFTER all required page locks for the frame have been successfully acquired. This restores the correct lock ordering (Page Lock -> ni_lock) consistent with VFS. [[email protected]: ni_readpage_cmpr was renamed to ni_read_folio_cmpr]

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix UMR hang in LAG error state unload During firmware reset in LAG mode, a race condition causes the driver to hang indefinitely while waiting for UMR completion during device unload. See [1]. In LAG mode the bond device is only registered on the master, so it never sees sys_error events from the slave. During firmware reset this causes UMR waits to hang forever on unload as the slave is dead but the master hasn't entered error state yet, so UMR posts succeed but completions never arrive. Fix this by adding a sys_error notifier that gets registered before MLX5_IB_STAGE_IB_REG and stays alive until after ib_unregister_device(). This ensures error events reach the bond device throughout teardown. [1] Call Trace: __schedule+0x2bd/0x760 schedule+0x37/0xa0 schedule_preempt_disabled+0xa/0x10 __mutex_lock.isra.6+0x2b5/0x4a0 __mlx5_ib_dereg_mr+0x606/0x870 [mlx5_ib] ? __xa_erase+0x4a/0xa0 ? _cond_resched+0x15/0x30 ? wait_for_completion+0x31/0x100 ib_dereg_mr_user+0x48/0xc0 [ib_core] ? rdmacg_uncharge_hierarchy+0xa0/0x100 destroy_hw_idr_uobject+0x20/0x50 [ib_uverbs] uverbs_destroy_uobject+0x37/0x150 [ib_uverbs] __uverbs_cleanup_ufile+0xda/0x140 [ib_uverbs] uverbs_destroy_ufile_hw+0x3a/0xf0 [ib_uverbs] ib_uverbs_remove_one+0xc3/0x140 [ib_uverbs] remove_client_context+0x8b/0xd0 [ib_core] disable_device+0x8c/0x130 [ib_core] __ib_unregister_device+0x10d/0x180 [ib_core] ib_unregister_device+0x21/0x30 [ib_core] __mlx5_ib_remove+0x1e4/0x1f0 [mlx5_ib] auxiliary_bus_remove+0x1e/0x30 device_release_driver_internal+0x103/0x1f0 bus_remove_device+0xf7/0x170 device_del+0x181/0x410 mlx5_rescan_drivers_locked.part.10+0xa9/0x1d0 [mlx5_core] mlx5_disable_lag+0x253/0x260 [mlx5_core] mlx5_lag_disable_change+0x89/0xc0 [mlx5_core] mlx5_eswitch_disable+0x67/0xa0 [mlx5_core] mlx5_unload+0x15/0xd0 [mlx5_core] mlx5_unload_one+0x71/0xc0 [mlx5_core] mlx5_sync_reset_reload_work+0x83/0x100 [mlx5_core] process_one_work+0x1a7/0x360 worker_thread+0x30/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x116/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x22/0x40

In the Linux kernel, the following vulnerability has been resolved: net/sched: taprio: fix NULL pointer dereference in class dump When a TAPRIO child qdisc is deleted via RTM_DELQDISC, taprio_graft() is called with new == NULL and stores NULL into q->qdiscs[cl - 1]. Subsequent RTM_GETTCLASS dump operations walk all classes via taprio_walk() and call taprio_dump_class(), which calls taprio_leaf() returning the NULL pointer, then dereferences it to read child->handle, causing a kernel NULL pointer dereference. The bug is reachable with namespace-scoped CAP_NET_ADMIN on any kernel with CONFIG_NET_SCH_TAPRIO enabled. On systems with unprivileged user namespaces enabled, an unprivileged local user can trigger a kernel panic by creating a taprio qdisc inside a new network namespace, grafting an explicit child qdisc, deleting it, and requesting a class dump. The RTM_GETTCLASS dump itself requires no capability. Oops: general protection fault, probably for non-canonical address 0xdffffc0000000007: 0000 [#1] SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f] RIP: 0010:taprio_dump_class (net/sched/sch_taprio.c:2478) Call Trace: <TASK> tc_fill_tclass (net/sched/sch_api.c:1966) qdisc_class_dump (net/sched/sch_api.c:2326) taprio_walk (net/sched/sch_taprio.c:2514) tc_dump_tclass_qdisc (net/sched/sch_api.c:2352) tc_dump_tclass_root (net/sched/sch_api.c:2370) tc_dump_tclass (net/sched/sch_api.c:2431) rtnl_dumpit (net/core/rtnetlink.c:6864) netlink_dump (net/netlink/af_netlink.c:2325) rtnetlink_rcv_msg (net/core/rtnetlink.c:6959) netlink_rcv_skb (net/netlink/af_netlink.c:2550) </TASK> Fix this by substituting &noop_qdisc when new is NULL in taprio_graft(), a common pattern used by other qdiscs (e.g., multiq_graft()) to ensure the q->qdiscs[] slots are never NULL. This makes control-plane dump paths safe without requiring individual NULL checks. Since the data-plane paths (taprio_enqueue and taprio_dequeue_from_txq) previously had explicit NULL guards that would drop/skip the packet cleanly, update those checks to test for &noop_qdisc instead. Without this, packets would reach taprio_enqueue_one() which increments the root qdisc's qlen and backlog before calling the child's enqueue; noop_qdisc drops the packet but those counters are never rolled back, permanently inflating the root qdisc's statistics. After this change *old can be a valid qdisc, NULL, or &noop_qdisc. Only call qdisc_put(*old) in the first case to avoid decreasing noop_qdisc's refcount, which was never increased.

In the Linux kernel, the following vulnerability has been resolved: SUNRPC: auth_gss: fix memory leaks in XDR decoding error paths The gssx_dec_ctx(), gssx_dec_status(), and gssx_dec_name() functions allocate memory via gssx_dec_buffer(), which calls kmemdup(). When a subsequent decode operation fails, these functions return immediately without freeing previously allocated buffers, causing memory leaks. The leak in gssx_dec_ctx() is particularly relevant because the caller (gssp_accept_sec_context_upcall) initializes several buffer length fields to non-zero values, resulting in memory allocation: struct gssx_ctx rctxh = { .exported_context_token.len = GSSX_max_output_handle_sz, .mech.len = GSS_OID_MAX_LEN, .src_name.display_name.len = GSSX_max_princ_sz, .targ_name.display_name.len = GSSX_max_princ_sz }; If, for example, gssx_dec_name() succeeds for src_name but fails for targ_name, the memory allocated for exported_context_token, mech, and src_name.display_name remains unreferenced and cannot be reclaimed. Add error handling with goto-based cleanup to free any previously allocated buffers before returning an error.

In the Linux kernel, the following vulnerability has been resolved: drm/display/dp_mst: Add protection against 0 vcpi When releasing a timeslot there is a slight chance we may end up with the wrong payload mask due to overflow if the delayed_destroy_work ends up coming into play after a DP 2.1 monitor gets disconnected which causes vcpi to become 0 then we try to make the payload = ~BIT(vcpi - 1) which is a negative shift. VCPI id should never really be 0 hence skip changing the payload mask if VCPI is 0. Otherwise it leads to <7> [515.287237] xe 0000:03:00.0: [drm:drm_dp_mst_get_port_malloc [drm_display_helper]] port ffff888126ce9000 (3) <4> [515.287267] -----------[ cut here ]----------- <3> [515.287268] UBSAN: shift-out-of-bounds in ../drivers/gpu/drm/display/drm_dp_mst_topology.c:4575:36 <3> [515.287271] shift exponent -1 is negative <4> [515.287275] CPU: 7 UID: 0 PID: 3108 Comm: kworker/u64:33 Tainted: G S U 6.17.0-rc6-lgci-xe-xe-3795-3e79699fa1b216e92+ #1 PREEMPT(voluntary) <4> [515.287279] Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER <4> [515.287279] Hardware name: ASUS System Product Name/PRIME Z790-P WIFI, BIOS 1645 03/15/2024 <4> [515.287281] Workqueue: drm_dp_mst_wq drm_dp_delayed_destroy_work [drm_display_helper] <4> [515.287303] Call Trace: <4> [515.287304] <TASK> <4> [515.287306] dump_stack_lvl+0xc1/0xf0 <4> [515.287313] dump_stack+0x10/0x20 <4> [515.287316] __ubsan_handle_shift_out_of_bounds+0x133/0x2e0 <4> [515.287324] ? drm_atomic_get_private_obj_state+0x186/0x1d0 <4> [515.287333] drm_dp_atomic_release_time_slots.cold+0x17/0x3d [drm_display_helper] <4> [515.287355] mst_connector_atomic_check+0x159/0x180 [xe] <4> [515.287546] drm_atomic_helper_check_modeset+0x4d9/0xfa0 <4> [515.287550] ? __ww_mutex_lock.constprop.0+0x6f/0x1a60 <4> [515.287562] intel_atomic_check+0x119/0x2b80 [xe] <4> [515.287740] ? find_held_lock+0x31/0x90 <4> [515.287747] ? lock_release+0xce/0x2a0 <4> [515.287754] drm_atomic_check_only+0x6a2/0xb40 <4> [515.287758] ? drm_atomic_add_affected_connectors+0x12b/0x140 <4> [515.287765] drm_atomic_commit+0x6e/0xf0 <4> [515.287766] ? _pfx__drm_printfn_info+0x10/0x10 <4> [515.287774] drm_client_modeset_commit_atomic+0x25c/0x2b0 <4> [515.287794] drm_client_modeset_commit_locked+0x60/0x1b0 <4> [515.287795] ? mutex_lock_nested+0x1b/0x30 <4> [515.287801] drm_client_modeset_commit+0x26/0x50 <4> [515.287804] __drm_fb_helper_restore_fbdev_mode_unlocked+0xdc/0x110 <4> [515.287810] drm_fb_helper_hotplug_event+0x120/0x140 <4> [515.287814] drm_fbdev_client_hotplug+0x28/0xd0 <4> [515.287819] drm_client_hotplug+0x6c/0xf0 <4> [515.287824] drm_client_dev_hotplug+0x9e/0xd0 <4> [515.287829] drm_kms_helper_hotplug_event+0x1a/0x30 <4> [515.287834] drm_dp_delayed_destroy_work+0x3df/0x410 [drm_display_helper] <4> [515.287861] process_one_work+0x22b/0x6f0 <4> [515.287874] worker_thread+0x1e8/0x3d0 <4> [515.287879] ? __pfx_worker_thread+0x10/0x10 <4> [515.287882] kthread+0x11c/0x250 <4> [515.287886] ? __pfx_kthread+0x10/0x10 <4> [515.287890] ret_from_fork+0x2d7/0x310 <4> [515.287894] ? __pfx_kthread+0x10/0x10 <4> [515.287897] ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: fix ntfs_mount_options leak in ntfs_fill_super() In ntfs_fill_super(), the fc->fs_private pointer is set to NULL without first freeing the memory it points to. This causes the subsequent call to ntfs_fs_free() to skip freeing the ntfs_mount_options structure. This results in a kmemleak report: unreferenced object 0xff1100015378b800 (size 32): comm "mount", pid 582, jiffies 4294890685 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 ed ff ed ff 00 04 00 00 ................ backtrace (crc ed541d8c): __kmalloc_cache_noprof+0x424/0x5a0 __ntfs_init_fs_context+0x47/0x590 alloc_fs_context+0x5d8/0x960 __x64_sys_fsopen+0xb1/0x190 do_syscall_64+0x50/0x1f0 entry_SYSCALL_64_after_hwframe+0x76/0x7e This issue can be reproduced using the following commands: fallocate -l 100M test.file mount test.file /tmp/test Since sbi->options is duplicated from fc->fs_private and does not directly use the memory allocated for fs_private, it is unnecessary to set fc->fs_private to NULL. Additionally, this patch simplifies the code by utilizing the helper function put_mount_options() instead of open-coding the cleanup logic.

Integer overflow in ANGLE in Google Chrome prior to 148.0.7778.216 allowed a remote attacker to obtain potentially sensitive information from process memory via a crafted HTML page. (Chromium security severity: Medium)

Insufficient validation of untrusted input in USB in Google Chrome prior to 148.0.7778.216 allowed a remote attacker to execute arbitrary code via a crafted HTML page. (Chromium security severity: Medium)

Use after free in Accessibility in Google Chrome prior to 148.0.7778.216 allowed a remote attacker who had compromised the renderer process to potentially perform a sandbox escape via a crafted HTML page. (Chromium security severity: High)

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix bpf_xdp_store_bytes proto for read-only arg While making some maps in Cilium read-only from the BPF side, we noticed that the bpf_xdp_store_bytes proto is incorrect. In particular, the verifier was throwing the following error: ; ret = ctx_store_bytes(ctx, l3_off + offsetof(struct iphdr, saddr), &nat->address, 4, 0); 635: (79) r1 = *(u64 *)(r10 -144) ; R1=ctx() R10=fp0 fp-144=ctx() 636: (b4) w2 = 26 ; R2=26 637: (b4) w4 = 4 ; R4=4 638: (b4) w5 = 0 ; R5=0 639: (85) call bpf_xdp_store_bytes#190 write into map forbidden, value_size=6 off=0 size=4 nat comes from a BPF_F_RDONLY_PROG map, so R3 is a PTR_TO_MAP_VALUE. The verifier checks the helper's memory access to R3 in check_mem_size_reg, as it reaches ARG_CONST_SIZE argument. The third argument has expected type ARG_PTR_TO_UNINIT_MEM, which includes the MEM_WRITE flag. The verifier thus checks for a BPF_WRITE access on R3. Given R3 points to a read-only map, the check fails. Conversely, ARG_PTR_TO_UNINIT_MEM can also lead to the helper reading from uninitialized memory. This patch simply fixes the expected argument type to match that of bpf_skb_store_bytes.