CVE Feed

In the Linux kernel, the following vulnerability has been resolved: media: vivid: fix cleanup bugs in vivid_init() When platform_device_register() fails in vivid_init(), the embedded struct device in vivid_pdev has already been initialized by device_initialize(), but the failure path jumps to free_output_strings without dropping the device reference for the current platform device: vivid_init() -> platform_device_register(&vivid_pdev) -> device_initialize(&vivid_pdev.dev) -> setup_pdev_dma_masks(&vivid_pdev) -> platform_device_add(&vivid_pdev) This leads to a reference leak when platform_device_register() fails. Fix this by calling platform_device_put() before jumping to the common cleanup path. Also, the unreg_driver label incorrectly calls platform_driver_register() instead of platform_driver_unregister(), which breaks cleanup when workqueue creation fails after successful driver registration. Fix that as well. The reference leak was identified by a static analysis tool I developed and confirmed by manual review. The incorrect cleanup call was found during code inspection.

In the Linux kernel, the following vulnerability has been resolved: afs: Fix afs_edit_dir_remove() to get, not find, block 0 Fix afs_edit_dir_remove() to use afs_dir_get_block() to get block 0 rather than afs_dir_find_block() as the latter caches the found block in the afs_dir_iter and may[*] switch out the page it's on if another afs_dir_find_block() is done. This parallels what afs_edit_dir_add() does. [*] There's more than one block per page.

In the Linux kernel, the following vulnerability has been resolved: staging: vme_user: fix location monitor leak in tsi148 bridge tsi148_probe() allocates a location monitor resource and links it into tsi148_bridge->lm_resources. The probe error path frees this list, but tsi148_remove() only frees the dma, slave and master resource lists, so the location monitor resource is leaked on device unbind or module unload. Free the lm_resources list in tsi148_remove() as well, before tsi148_bridge is freed.

In the Linux kernel, the following vulnerability has been resolved: mm/khugepaged: write all dirty file folios when collapsing [There is no upstream commit, as this code was removed by upstream commit 044925f9b565 ("mm: fs: remove filemap_nr_thps*() functions and their users")] As-is, khugepaged and writable-file opening exclude each other. A file cannot be open writeable and have THPs (because the filesystem is not aware of them). khugepaged will never collapse file pages for files that are opened writeable. On an open(O_RDWR/O_WRONLY), the page cache for that particular file is dropped. This is fine because nothing could've been dirtied. However, there is an edge-case: collapse_file() might not be able to coexist with concurrent writers, but it can coexist with dirty folios (from previous writers). Therefore, the following can happen: open(file, O_RDWR) write(file) close(file) madvise(file_mapping, MADV_COLLAPSE, some non-dirty range) open(file, O_RDWR) nr_thps > 0 truncate_inode_pages() /* THPs are cleared out, but so are the dirty folios */ When this edge-case happens, there is data loss, as the dirty folios are fully discarded. Fix it by fully writing back the page cache (and waiting) when collapsing file THPs. Doing so provides the guarantee that no dirty folio will be observed while there are active THPs. To fully ensure this is safe, the invalidate_lock needs to be held while doing the writeout, so that do_dentry_open()'s page cache truncation excludes this write-and-wait. As a side effect, move the nr_thps counter bumping outside the i_pages lock. This is correct since the counter itself is an atomic_t and the producer <-> consumer correctness is provided by a full memory barrier: smp_mb() in collapse_file()/memory barrier implied by full ordering in get_write_access() -> atomic_inc_unless_negative().

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/sdma7.1: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit c4f230b51cf2d3e7e8b1c800331f3dbed2a9e3f5)

In the Linux kernel, the following vulnerability has been resolved: net: drop_monitor: fix info leak in NET_DM_ATTR_PAYLOAD net_dm_packet_report_fill() and net_dm_hw_packet_report_fill() open code the NET_DM_ATTR_PAYLOAD attribute to avoid zeroing the packet payload before overwriting it with skb_copy_bits(). skb_put() reserves nla_total_size(payload_len), i.e. the header plus the NLA_ALIGN() padding, but only payload_len bytes are copied in. When payload_len is not a multiple of 4 the 1-3 padding bytes are never initialized and are leaked to user space inside the netlink message. KMSAN confirms the leak for the software path when the packet payload length is not 4-byte aligned: BUG: KMSAN: kernel-infoleak in _copy_to_iter _copy_to_iter __skb_datagram_iter skb_copy_datagram_iter netlink_recvmsg sock_recvmsg __sys_recvfrom Uninit was created at: kmem_cache_alloc_node_noprof __alloc_skb net_dm_packet_work Bytes 173-175 of 176 are uninitialized Use __nla_reserve(), which sets up the attribute header and zeroes the padding, instead of open coding the attribute construction.

In the Linux kernel, the following vulnerability has been resolved: drm/dp/mst: fix OOB reads on 2-byte fields in sideband reply parsers Three sideband reply parsers read 16-bit fields as: val = (raw->msg[idx] << 8) | (raw->msg[idx+1]); and check bounds only after the fact. When idx == raw->curlen, raw->msg[idx+1] reads one byte past the received message data into the following struct fields (curchunk_len, curchunk_idx, curlen). Affected functions: - drm_dp_sideband_parse_enum_path_resources_ack() full_payload_bw_number and avail_payload_bw_number fields - drm_dp_sideband_parse_allocate_payload_ack() allocated_pbn field - drm_dp_sideband_parse_query_payload_ack() allocated_pbn field Fix by using a single combined check (idx + 2 > curlen) before each 2-byte read. Since the check is strictly tighter than idx > curlen, no separate step is needed. [added fixes tag]

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/sdma6.0: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit c17a508a7d652da3728f8bbc481bfffe96d65a87)

In the Linux kernel, the following vulnerability has been resolved: drm/xe/pt: Reset current_op in xe_pt_update_ops_init() xe_pt_update_ops_init() fails to reset current_op to 0. On the vm_bind path, ops_execute() calls xe_pt_update_ops_prepare() inside the xe_validation_guard() / drm_exec_until_all_locked() loop. When that loop retries due to lock contention or OOM eviction (drm_exec_retry_on_contention() / xe_validation_retry_on_oom()), xe_pt_update_ops_prepare() runs again on the same vops, and each call to bind_op_prepare() increments current_op without resetting it. After N retries current_op exceeds the array size allocated by xe_vma_ops_alloc(), causing an out-of-bounds write into SLUB-poisoned memory and a subsequent UAF crash in xe_migrate_update_pgtables_cpu() when reading the corrupted pt_op->bind. Also reset needs_svm_lock and needs_invalidation which are derived in the same prepare pass and would otherwise cause wrong migrate ops selection and redundant TLB invalidation on retry. Fix this by resetting current_op, needs_svm_lock and needs_invalidation in xe_pt_update_ops_init(). v2 (Matt): - Add details in commit message. - Add Fixes tag and Cc to [email protected] (cherry picked from commit 046045543e530605c441063535e7dca0075369a6)

In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: set have_execfd only once the interpreter is opened load_misc_binary() raises bprm->have_execfd as soon as it sees the 'O' (or 'C') flag. This happens well before it opens the interpreter. If that open fails the flag stays set on the bprm. binfmt_misc is at the head of the format list so an interpreter open failure that returns -ENOEXEC lets the search fall through to a later format. This means it runs the matched binary directly having never staged an interpreter. So bprm->executable is NULL while have_execfd falsely claims a descriptor is present. Consequently, begin_new_exec() dereferences the missing executable: would_dump(bprm, bprm->executable); and NULL derefs. Had it not, the hand-off later in the same function would have failed anyway. FD_ADD(0, bprm->executable) rejects a NULL file with -ENOMEM. Both sites are past the point of no return so the exec cannot be unwound either way. This can be reached by unprivileged users as binfmt_misc can be mounted in user namespaces. So a user can register an 'O' entry whose interpreter lives on a FUSE mount, have the FUSE server fail the open with -ENOEXEC and execute a native ELF file that matches the entry. have_execfd only means anything alongside the executable it describes which is not set until the interpreter has been opened and staged. So lets raise it there, next to execfd_creds, which is already set at that point. An open failure now leaves it clear, so the fallback format derives credentials from the binary and emits no AT_EXECFD, as it would for any native exec. The argv rewrite load_misc_binary() performs before the open is still not undone. This means the binary sees the interpreter path in argv[0] and its own path in argv[1] but that predates this change and only became observable once the exec stopped faulting.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: Protect UUID list traversal The hci_sync conversion moved class-of-device and EIR generation from an HCI request built under hdev->lock to asynchronous command sync work. The worker holds hdev->req_lock, but that lock does not serialize access to hdev->uuids against add_uuid() and remove_uuid(), which update the list under hdev->lock. The following interleaving can therefore occur: CPU0 (command sync work) CPU1 (management socket) fetch uuid from the list list_del(&uuid->list) kfree(uuid) read uuid->size KASAN reports the resulting use-after-free: BUG: KASAN: slab-use-after-free in eir_create+0xb8f/0xee0 Read of size 1 at addr ffff88810dbd8620 by task kworker/u17:0/87 Workqueue: hci0 hci_cmd_sync_work Call Trace: eir_create+0xb8f/0xee0 hci_update_eir_sync+0x1c0/0x330 hci_cmd_sync_work+0x13c/0x290 process_one_work+0x63a/0x1070 worker_thread+0x45b/0xd10 Allocated by task 86: __kasan_kmalloc+0x8f/0xa0 add_uuid+0x18a/0x4b0 hci_sock_sendmsg+0x1033/0x1ea0 Freed by task 92: __kasan_slab_free+0x43/0x70 kfree+0x131/0x3c0 remove_uuid+0x25e/0x560 hci_sock_sendmsg+0x1033/0x1ea0 Hold hdev->lock while generating and committing the class-of-device and EIR snapshots. Release it before sending an HCI command, so controller waits do not happen under the device lock. This protects all UUID list walks in these paths and restores the serialization lost in the command sync conversion.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Use sender devcom for MPV master-up After PCIe DPC recovery, mlx5 reloads the affected functions and replays multiport affiliation events. In the reported failure, the first relevant device error was: pcieport 0000:10:01.1: DPC: containment event pcieport 0000:10:01.1: PCIe Bus Error: severity=Uncorrected (Fatal) pcieport 0000:10:01.1: [ 5] SDES (First) mlx5 recovered the PCI functions and resumed 0000:11:00.1. During that resume, RDMA multiport binding replayed MLX5_DRIVER_EVENT_AFFILIATION_DONE and mlx5e sent MPV_DEVCOM_MASTER_UP. The host then panicked with: BUG: kernel NULL pointer dereference, address: 0000000000000010 RIP: mlx5_devcom_comp_set_ready+0x5/0x40 [mlx5_core] RDI: 0000000000000000 Call trace included: mlx5_devcom_comp_set_ready mlx5e_devcom_event_mpv mlx5_devcom_send_event mlx5_ib_bind_slave_port mlx5r_mp_probe mlx5_pci_resume MPV devcom registration publishes mlx5e private data to the component peer list before mlx5e_devcom_init_mpv() stores the returned component device in priv->devcom. A concurrent master-up event can therefore reach a peer whose private data is visible but whose priv->devcom backpointer is still NULL. MPV_DEVCOM_MASTER_UP already carries the sender/master mlx5e private data as event_data. The ready bit is stored on the shared devcom component, not on an individual peer. Use the sender devcom when marking the MPV component ready. This preserves the readiness transition while avoiding a NULL dereference of the peer devcom pointer during affiliation replay after PCI error recovery.

In the Linux kernel, the following vulnerability has been resolved: iio: core: fix uninitialized data in debugfs If *ppos is non-zero then simple_write_to_buffer() will not initialize the start of buf[]. Non zero values for *ppos aren't going to work anyway. Test for them at the start of the function and return -EINVAL.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: function: rndis: add length check to response query Add variable representations for BufLength and BufOffset in rndis_query_response(), and perform a length check on them. This is identical to how rndis_set_response() handles these parameters.

In the Linux kernel, the following vulnerability has been resolved: gpu: host1x: Fix use-after-free in host1x_bo_clear_cached_mappings __host1x_bo_unpin() drops the last reference to the mapping and frees it, so we can't dereference mapping afterwards. The cache itself outlives the mapping, so use the cache local variable instead.

In the Linux kernel, the following vulnerability has been resolved: xfrm: reject optional IPTFS templates in outbound policies syzbot reported a stack-out-of-bounds read in xfrm_state_find() which flows from xfrm_tmpl_resolve_one(). Commit 3d776e31c841 ("xfrm: Reject optional tunnel/BEET mode templates in outbound policies") disallowed optional tunnel and BEET in outbound policies to prevent this. Later when IPTFS added, it was not covered by that fix and can still trigger the out-of-bounds read; Extend the check to disallow optional IPTFS in outbound policies as well. IPTFS should be identical to tunnel mode. IN and FWD policies are not affected: xfrm_tmpl_resolve_one() is only reachable via the outbound path. Reproducer, before: ip link add dummy0 type dummy ip link set dummy0 up ip addr add 10.1.1.1/24 dev dummy0 ip xfrm policy add src 10.1.1.1/32 dst 10.1.1.2/32 dir out tmpl src fc00::dead:1 dst fc00::dead:2 proto esp reqid 1 mode iptfs level use tmpl src fc00::dead:1 dst fc00::dead:2 proto esp reqid 2 mode transport ping -W 1 -c 1 10.1.1.2 PING 10.1.1.2 (10.1.1.2) 56(84) bytes of data. [ 64.168420] ================================================================== [ 64.169977] BUG: KASAN: stack-out-of-bounds in __xfrm6_addr_hash+0x11e/0x170 [ 64.169977] Read of size 4 at addr ffff88800e1ffd20 by task ping/2844 [ 64.169977] CPU: 2 UID: 0 PID: 2844 Comm: ping Not tainted 7.1.0-rc7-00180-geb23b588430a #98 PREEMPT(full) [ 64.169977] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 64.169977] Call Trace: [ 64.169977] <TASK> [ 64.169977] dump_stack_lvl+0x47/0x70 [ 64.169977] ? __xfrm6_addr_hash+0x11e/0x170 [ 64.169977] print_report+0x152/0x4b0 [ 64.169977] ? ksys_mmap_pgoff+0x6d/0xa0 [ 64.169977] ? entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 64.169977] ? rcu_read_unlock_sched+0xa/0x20 [ 64.169977] ? __virt_addr_valid+0x21b/0x230 [ 64.169977] ? __xfrm6_addr_hash+0x11e/0x170 [ 64.169977] kasan_report+0xa8/0xd0 [ 64.169977] ? __xfrm6_addr_hash+0x11e/0x170 [ 64.169977] __xfrm6_addr_hash+0x11e/0x170 [ 64.169977] __xfrm_dst_hash+0x24/0xc0 [ 64.169977] xfrm_state_find+0xa2d/0x2f90 [ 64.169977] ? __pfx_xfrm_state_find+0x10/0x10 [ 64.169977] ? __pfx_ftrace_graph_ret_addr+0x10/0x10 [ 64.169977] ? __pfx_ftrace_graph_ret_addr+0x10/0x10 [ 64.169977] xfrm_tmpl_resolve_one+0x210/0x570 [ 64.169977] ? __pfx_xfrm_tmpl_resolve_one+0x10/0x10 [ 64.169977] ? __pfx_stack_trace_consume_entry+0x10/0x10 [ 64.169977] ? kernel_text_address+0x5b/0x80 [ 64.169977] ? __kernel_text_address+0xe/0x30 [ 64.169977] ? unwind_get_return_address+0x5e/0x90 [ 64.169977] ? arch_stack_walk+0x8c/0xe0 [ 64.169977] xfrm_tmpl_resolve+0x130/0x200 [ 64.169977] ? __pfx_xfrm_tmpl_resolve+0x10/0x10 [ 64.169977] ? __pfx_xfrm_policy_inexact_lookup_rcu+0x10/0x10 [ 64.169977] ? __refcount_add_not_zero.constprop.0+0xb2/0x110 [ 64.169977] ? __pfx___refcount_add_not_zero.constprop.0+0x10/0x10 [ 64.169977] xfrm_resolve_and_create_bundle+0xd5/0x310 [ 64.169977] ? __pfx_xfrm_resolve_and_create_bundle+0x10/0x10 [ 64.169977] ? __pfx_xfrm_policy_lookup_bytype+0x10/0x10 [ 64.169977] ? __pfx_xfrm_policy_lookup_bytype+0x10/0x10 [ 64.169977] xfrm_lookup_with_ifid+0x3d8/0xb80 [ 64.169977] ? __pfx_xfrm_lookup_with_ifid+0x10/0x10 [ 64.169977] ? ip_route_output_key_hash+0xc6/0x110 [ 64.169977] ? kasan_save_track+0x10/0x30 [ 64.169977] xfrm_lookup_route+0x18/0xe0 [ 64.169977] ip4_datagram_release_cb+0x4c9/0x530 [ 64.169977] ? __pfx_ip4_datagram_release_cb+0x10/0x10 [ 64.169977] ? do_raw_spin_lock+0x71/0xc0 [ 64.169977] ? __pfx_do_raw_spin_lock+0x10/0x10 [ 64.169977] release_sock+0xb0/0x170 [ 64.169977] udp_connect+0x43/0x50 [ 64.169977] __sys_connect+0xa6/0x100 [ 64.169977] ? alloc_fd+0x2e9/0x300 [ 64.169977] ? __pfx___sys_connect+0x10/0x10 [ 64.169977] ? preempt_latency ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: convert pmsr_free_wk to wiphy_work to fix deadlock When a netlink socket that owns a PMSR session is closed, cfg80211_release_pmsr() clears the request's nl_portid and queues pmsr_free_wk to call cfg80211_pmsr_process_abort() asynchronously. If the interface tears down concurrently, cfg80211_pmsr_wdev_down() is called under wiphy_lock and calls cancel_work_sync(&pmsr_free_wk) to wait for any running work. The work function acquires wiphy_lock via guard(wiphy) before calling process_abort. This is a deadlock: wdev_down holds wiphy_lock and blocks inside cancel_work_sync(); pmsr_free_wk blocks trying to acquire that same wiphy_lock. Neither thread can proceed. The same deadlock is reachable from cfg80211_leave_locked(), which calls cfg80211_pmsr_wdev_down() for all interface types under wiphy_lock. Fix this by converting pmsr_free_wk from a plain work_struct to a wiphy_work. The wiphy_work dispatcher holds wiphy_lock when running work items, so the explicit guard(wiphy) in the work function is no longer needed. wiphy_work_cancel() can be called safely while holding wiphy_lock - since wiphy_lock prevents the work from running concurrently, wiphy_work_cancel() never blocks, eliminating the deadlock. Remove the cancel_work_sync() for pmsr_free_wk from the NETDEV_GOING_DOWN handler. cfg80211_leave(), called unconditionally just before it, already cancels any pending work under wiphy_lock via wiphy_work_cancel() inside cfg80211_pmsr_wdev_down().

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: initialize SDIO data work before cleanup brcmf_sdio_probe() stores the newly allocated bus in sdiodev->bus before allocating the ordered workqueue. If that allocation fails, the function jumps to fail and calls brcmf_sdio_remove(). brcmf_sdio_remove() unconditionally cancels bus->datawork. Initialize the work item before the first failure path that can reach brcmf_sdio_remove(), so the cleanup path always observes a valid work object. This issue was found by our static analysis tool and then confirmed by manual review of the probe error path and the remove-time work drain. The problem pattern is an early setup failure that reaches a cleanup helper which cancels an embedded work item before its initializer has run. A QEMU PoC forced alloc_ordered_workqueue() to fail at the same point in brcmf_sdio_probe(), before INIT_WORK(&bus->datawork) is reached. The resulting fail path calls brcmf_sdio_remove(), and DEBUG_OBJECTS reports the invalid work drain with brcmf_sdio_probe() and brcmf_sdio_remove() in the stack.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: mgmt: hold reference for hci_conn in mgmt_pending_cmds Dereferencing RCU-protected pointers outside critical sections is invalid and may lead to UAF. Use of hci_conn in hci_sync callbacks also needs to hold refcount to avoid UAF. Take appropriate locks for hci_conn lookups, and take refcount for hci_conn pointers stored in mgmt_pending_cmd so that the pointer stays valid. When accessing conn->state, ensure hdev->lock is held to avoid data race.

In the Linux kernel, the following vulnerability has been resolved: tcp: fix TIME_WAIT socket reference leak on PSP policy failure Release the TIME_WAIT socket reference and jump to discard_it upon PSP policy failure in both IPv4 and IPv6 receive paths. This prevents a memory leak of tcp_tw_bucket structures.

In the Linux kernel, the following vulnerability has been resolved: usb: core: port: Deattach Type-C connector on component unbind connector_unbind() is the mirror of connector_bind(), but it is missing the symmetric call to typec_deattach() that connector_bind() makes via: if (port_dev->child) typec_attach(port_dev->connector, &port_dev->child->dev); When a Thunderbolt dock is unplugged, two teardown paths race: 1. The component framework calls connector_unbind() first, which sets port_dev->connector = NULL without calling typec_deattach(). This leaves port->usb2_dev/port->usb3_dev in struct typec_port pointing at the USB device that is about to be freed. 2. usb_disconnect() then calls typec_deattach(port_dev->connector, ...), but port_dev->connector is already NULL, so the call is a no-op and port->usb2_dev is never cleared. 3. Concurrently, UCSI detects a PD partner-disconnect event and calls typec_unregister_partner(), which reads port->usb2_dev (now a dangling pointer to freed memory) and passes it to typec_partner_unlink_device() -> sysfs_remove_link() -> dev_name() on the freed device, corrupting the typec/UCSI partner state. This corruption leaves the Thunderbolt tunnel in an inconsistent state on the next dock hot-plug. On affected hardware the dock's I225/igc NIC fails to enumerate: AER fires a slot reset while the igc driver is still initialising ("PCIe link lost"), and the subsequent igc_reset attempt hits igc_rd32 on an already-detached device: igc 0000:2e:00.0 eth0: PCIe link lost, device now detached igc: Failed to read reg 0x0! WARNING: CPU: 9 PID: 129 at drivers/net/ethernet/intel/igc/igc_main.c:7005 igc_rd32+0xa4/0xc0 [igc] Call Trace: igc_disable_pcie_master+0x16/0xa0 [igc] igc_reset_hw_base+0x14/0x170 [igc] igc_reset+0x63/0x110 [igc] igc_io_slot_reset+0x9e/0xd0 [igc] report_slot_reset+0x5d/0xc0 pcie_do_recovery+0x209/0x400 aer_isr_one_error_type+0x235/0x430 aer_isr+0x4e/0x80 irq_thread+0xf4/0x1f0 4. UCSI later handles the PD partner-disconnect and calls typec_unregister_partner(), which still sees the stale port->usb2_dev and tries to remove its sysfs link a second time: kernfs: can not remove 'typec', no directory WARNING: CPU: 6 PID: 55 at fs/kernfs/dir.c:1706 kernfs_remove_by_name_ns+0xe9/0xf0 Workqueue: events ucsi_handle_connector_change [typec_ucsi] Call Trace: sysfs_remove_link+0x19/0x50 typec_unregister_partner+0x6e/0x120 [typec] ucsi_unregister_partner+0x107/0x150 [typec_ucsi] ucsi_handle_connector_change+0x3ec/0x490 [typec_ucsi] process_one_work+0x18e/0x3e0 worker_thread+0x2e3/0x420 kthread+0x10a/0x230 ret_from_fork+0x121/0x140 ret_from_fork_asm+0x1a/0x30 With worse timing the same stale pointer is dereferenced after the backing memory is freed, turning the warning into a use-after-free. Fix the asymmetry: call typec_deattach() before clearing port_dev->connector, matching what connector_bind() does on the bind side. typec_partner_deattach() is already protected by port->partner_link_lock, so it serialises safely with the concurrent typec_unregister_partner() path.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (nzxt-smart2) Stop device IO before calling hid_hw_stop Calling hid_hw_stop() does not stop the device IO. This results in a race condition between hid_input_report() and the point immediately following the execution of hid_device_io_start() within the driver probe function. If the probe operation fails after "io start" has been initiated, this race condition will result in a UAF vulnerability. Fix the problem by calling hid_device_io_stop() before calling hid_hw_stop().

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7925: guard link STA in decap offload mt7925_sta_set_decap_offload() iterates over the vif valid_links mask when updating decap offload state for an MLO station. The station may not have a link STA for every valid link of the vif, so mt792x_sta_to_link() can return NULL for a link that belongs to the vif but not to the station. The function currently dereferences mlink before checking whether the link WCID is ready. If mlink is NULL, setting or clearing MT_WCID_FLAG_HDR_TRANS dereferences a NULL pointer. Skip links without a station link before touching mlink->wcid.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7915: guard HE capability lookups mt7915_mcu_bss_he_tlv() and mt7915_mcu_sta_bfer_tlv() both run after checking HE support, then dereference the HE PHY capability returned by mt76_connac_get_he_phy_cap(). That helper can return NULL when no capability entry matches the vif type. Fetch the capability before appending the TLV and skip the HE-specific setup when no matching capability is available.

In the Linux kernel, the following vulnerability has been resolved: net: hsr: fix memory leak on slave unregistration by removing synced VLANs When an HSR master device is brought UP, it auto-adds VLAN 0 via vlan_vid0_add(), which propagates VID 0 to its slave devices (slave A and B). If a slave device is later unregistered while HSR is active (e.g., during netns cleanup or interface destruction), hsr_del_port() is called to detach the slave port from the HSR master. However, hsr_del_port() currently does not delete the VLAN IDs that were synced to the slave device by HSR. As a result, the slave device retains a refcount on VID 0 (and any other synced VLANs). When the slave device is destroyed, its vlan_info / vlan_vid_info structure remains allocated, leading to a memory leak. Fix this by calling vlan_vids_del_by_dev(port->dev, master->dev) in hsr_del_port() before unlinking slave A or slave B ports, matching the propagation logic in hsr_ndo_vlan_rx_add_vid() / hsr_ndo_vlan_rx_kill_vid() and the cleanup behavior in bonding and team drivers.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: BPF: Fix memory leak in bpf_jit_free() When bpf_int_jit_compile() is called for subprograms, it returns early during the first pass (!prog->is_func || extra_pass is false), keeping ctx->offset alive for the subsequent extra pass. If JIT compilation fails for a later subprogram, the BPF core aborts and calls bpf_jit_free() to clean up the first subprogram. However, bpf_jit_free() fails to free jit_data->ctx.offset, which causes a memory leak of the JIT context offsets array. So fix this by adding the missing kvfree(jit_data->ctx.offset) in bpf_jit_free().

In the Linux kernel, the following vulnerability has been resolved: drm/xe: Hold a dma-buf reference for imported BOs An imported dma-buf BO is created as a ttm_bo_type_sg BO whose reservation object is the exporter's dma_buf->resv. The importer, however, only takes a dma-buf reference after a successful dma_buf_dynamic_attach(). Until then nothing keeps the exporter alive, so if the exporter is freed while the BO still references its resv, a later access to that resv is a use-after-free: Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b9c Workqueue: ttm ttm_bo_delayed_delete [ttm] RIP: 0010:mutex_can_spin_on_owner+0x3f/0xc0 This can be reached on two paths: - dma_buf_dynamic_attach() fails, or - ttm_bo_init_reserved() fails during BO creation. In both cases the BO already has bo->base.resv pointing at the exporter resv, and sg BOs are always torn down via ttm_bo_delayed_delete(), which locks bo->base.resv asynchronously - potentially after the exporter has been freed. Take the dma-buf reference in xe_bo_init_locked(), before ttm_bo_init_reserved(), so it also covers a creation failure there, and release it in xe_ttm_bo_destroy(). The reference is held for the whole BO lifetime, keeping the shared resv alive on every path. v2: - Reworked the fix to avoid creating the imported sg BO before dma_buf_dynamic_attach() succeeds. - Attach with importer_priv == NULL and make invalidate_mappings ignore incomplete imports. v3: - Dropped the xe-side reordering approach since importer_priv must be valid when dma_buf_dynamic_attach() publishes the attachment. - Per Christian's suggestion on the v1 thread, keyed the check on import_attach rather than removing the sg guard entirely. - Fixes both xe and amdgpu in a single TTM patch. v4: - Moved import_attach check to after dma_resv_copy_fences() so fences are copied before returning for successful imports (Thomas). - Removed exporter-alive claim from commit message (Thomas). v5: - Add drm/xe patch to keep imported sg BOs off the LRU before attach succeeds; the TTM fix alone is not sufficient for xe if the BO is already LRU-visible. (Thomas) v4 patch: https://patchwork.freedesktop.org/patch/736663/?series=169129&rev=2 - Patch 1 (drm/ttm) carries Christian's Reviewed-by from v4. v6: - Reworked the fix based on Thomas' suggestion. Instead of the TTM resv individualization (v1-v5) plus the xe off-LRU/placement handling (v5), just hold a dma-buf reference for the imported BO lifetime so the shared resv can never be freed while the BO still references it. Single xe patch, no TTM change. (Thomas) - Take the reference in xe_bo_init_locked() before ttm_bo_init_reserved() so a TTM creation failure is covered too (Thomas). - Dropped the v5 series (drm/ttm + drm/xe off-LRU); the off-LRU approach also regressed in CI BAT via ttm_bo_pipeline_gutting() creating a ghost BO that outlived the exporter. Link to v5: https://patchwork.freedesktop.org/series/169984/ v7: - Move changelog above --- so it stays in the commit message. - Reorder changelog entries oldest-to-newest. (Thomas) (cherry picked from commit 3516f3fae6be35642f8f06f8a218da6425c0306a)

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/sdma7.0: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit 9723a8bed3aa251a26bee4583bac9d8fb064dd44)

In the Linux kernel, the following vulnerability has been resolved: drm/ttm: Account for NULL and handle pages in ttm_pool_backup Pages in ttm_pool_backup can be NULL or backup handles (ttm_backup_page_ptr_is_handle()), neither of which can be passed to set_pages_array_wb() or freed. Add a dedicated WB pass before the dma/purge loop that walks allocations using the same i += num_pages stride, skipping NULL and handle entries, and calls set_pages_array_wb() once per contiguous run of real pages. Apply the same NULL/handle guard to the dma/purge loop. Fixes the following oops: Oops: general protection fault, kernel NULL pointer dereference 0x0: 0000 [#1] SMP NOPTI RIP: 0010:__cpa_process_fault+0xf8/0x770 RSP: 0018:ffffc90000a87718 EFLAGS: 00010287 RAX: 0000000000000000 RBX: ffffc90000a87868 RCX: 0000000000000000 RDX: 0000000000001000 RSI: 0005088000000000 RDI: ffffffff827c5f34 RBP: 0005088000000000 R08: ffffc90000a877cb R09: ffffc90000a877d0 R10: 0000000000000000 R11: 000000000000001b R12: 000ffffffffff000 R13: ffffc90000a87868 R14: ffffc90000a87868 R15: ffff88815b882ae0 FS: 0000000000000000(0000) GS:ffff8884ec840000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f930b844000 CR3: 000000000262e003 CR4: 0000000008f70ef0 PKRU: 55555554 Call Trace: <TASK> __change_page_attr_set_clr+0x989/0xe90 ? __purge_vmap_area_lazy+0x6c/0x3a0 ? _vm_unmap_aliases+0x250/0x2a0 set_pages_array_wb+0x7f/0x120 ttm_pool_backup+0x4c9/0x5b0 [ttm] ? dma_resv_wait_timeout+0x3b/0xf0 ttm_tt_backup+0x32/0x60 [ttm] ttm_bo_shrink+0x66/0x110 [ttm] xe_bo_shrink_purge+0x12b/0x1b0 [xe] xe_bo_shrink+0xbb/0x270 [xe] __xe_shrinker_walk+0xf7/0x160 [xe] xe_shrinker_walk+0x9d/0xc0 [xe] xe_shrinker_scan+0x11f/0x210 [xe] do_shrink_slab+0x13b/0x270 shrink_slab+0xf1/0x400 shrink_node+0x352/0x8a0 balance_pgdat+0x32c/0x700 kswapd+0x205/0x2f0 ? __pfx_autoremove_wake_function+0x10/0x10 ? __pfx_kswapd+0x10/0x10 kthread+0xd1/0x110 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x1b1/0x200 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: fix NULL dereference when the AP has HT-cap but no HT-oper mwifiex_tdls_add_ht_oper() gates its follow-the-AP-bandwidth path on bss_desc->bcn_ht_cap being present, but then dereferences a different pointer, bss_desc->bcn_ht_oper: if (ISSUPP_CHANWIDTH40(priv->adapter->hw_dot_11n_dev_cap) && bss_desc->bcn_ht_cap && ISALLOWED_CHANWIDTH40(bss_desc->bcn_ht_oper->ht_param)) bcn_ht_cap and bcn_ht_oper are populated independently while parsing the associated AP's beacon in mwifiex_update_bss_desc_with_ie(): an AP that advertises an HT Capabilities element but no HT Operation element leaves bcn_ht_cap non-NULL and bcn_ht_oper NULL. Setting up a TDLS link to a peer while associated to such an AP then dereferences the NULL bcn_ht_oper and crashes the kernel. Every other bcn_ht_oper user in the driver NULL-checks it first. Guard on the pointer that is actually dereferenced. Found by 0sec automated security-research tooling (https://0sec.ai).

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7615: drop TXRX_NOTIFY on non-mmio buses PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7615_rx_check() and mt7615_queue_rx_skb() dispatch it to mt7615_mac_tx_free() on every bus. mt7615_mac_tx_free() cleans the DMA tx queues with mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the mmio queue ops implement that callback; on the mt7663 USB and SDIO buses it is NULL, so a TXRX_NOTIFY there calls a NULL pointer in the RX worker. Same defect as the mt7921 and mt7925 patches in this series. Drop the event on non-mmio buses via mt76_is_mmio(), as in commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for non-mmio devices").

In the Linux kernel, the following vulnerability has been resolved: firmware: stratix10-svc: fix memory leaks and list corruption bugs Fix a memory leak when gen_pool_alloc() fails by freeing pmem on the error path. Switch pmem allocation from devm_kzalloc() to kzalloc() with explicit kfree() in the free path to match its list-managed lifetime. Remove the erroneous list_del(&svc_data_mem) which corrupted the list head on failed lookups.

In the Linux kernel, the following vulnerability has been resolved: ublk: wait on ublk_dev_ready() instead of ub->completion ub->completion is only re-armed by a successful START_USER_RECOVERY. If the ublk server sends END_USER_RECOVERY without one - e.g. its START failed with -EBUSY and the error was ignored - the wait is satisfied by the stale completion of the previous recovery cycle, and the device is marked LIVE and the requeue list kicked while the FETCH stream is still running and ubq->canceling is still set. The kick redispatches a previously requeued request, __ublk_queue_rq_common() sees ->canceling and parks it again via __ublk_abort_rq(), and after the last FETCH clears ->canceling nothing ever kicks the requeue list again: the request is stranded there while holding its tag. If it is the flush machinery's flush_rq, every subsequent fsync piles up in uninterruptible sleep and teardown hangs on tag draining. This matches a report of a lost PREFLUSH with ext4 on top of ublk after daemon crash recovery. ub->completion is an edge-triggered latch used as a proxy for the level condition "every queue has fetched all I/O commands", which can regress (F_BATCH's UNPREP, daemon death) and whose re-arm can be skipped. Drop it and wait on the real condition instead: the new helper ublk_wait_dev_ready_and_lock() waits on ublk_dev_ready() via wait_var_event_interruptible(), woken from ublk_mark_io_ready(), then re-checks it under ub->mutex, waiting again on regression, and returns with the mutex held and readiness guaranteed. Readiness becomes true in the same ub->mutex critical section that clears the last queue's ->canceling, so END_USER_RECOVERY marks the device LIVE and kicks the requeue list strictly after ->canceling clears. The wait stays interruptible, so a server whose daemon died can still be signalled out. For ublk_ctrl_start_dev() this replaces the fail-fast -EINVAL on an F_BATCH ready->UNPREP regression with waiting until the device is ready again.

In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: userspace: fix use-after-free in get_local_id In mptcp_pm_userspace_get_local_id(), the address entry is looked up under spinlock, but its id is read after dropping the lock. A concurrent deletion can free the entry between the unlock and the read, leading to UAF. The race window is narrow. It was reproduced only with a locally constructed stress test that repeatedly overlaps an MP_JOIN SYN with a MPTCP_PM_CMD_SUBFLOW_DESTROY request. However, the KASAN report below confirms that the race is reachable: [ 666.319376] BUG: KASAN: slab-use-after-free in mptcp_userspace_pm_get_local_id+0x1dc/0x1f0 [ 666.319386] Read of size 1 at addr ffff888124845610 by task swapper/0/0 ... [ 666.319401] Call Trace: [ 666.319405] <IRQ> [ 666.319408] dump_stack_lvl+0x53/0x70 [ 666.319412] print_address_description.constprop.0+0x2c/0x3b0 [ 666.319418] print_report+0xbe/0x2b0 [ 666.319421] ? mptcp_userspace_pm_get_local_id+0x1dc/0x1f0 [ 666.319423] kasan_report+0xce/0x100 [ 666.319426] ? mptcp_userspace_pm_get_local_id+0x1dc/0x1f0 [ 666.319429] mptcp_userspace_pm_get_local_id+0x1dc/0x1f0 [ 666.319433] mptcp_pm_get_local_id+0x371/0x440 ... [ 666.319821] Allocated by task 45539: [ 666.319844] kasan_save_stack+0x33/0x60 [ 666.319855] kasan_save_track+0x14/0x30 [ 666.319858] __kasan_kmalloc+0x8f/0xa0 [ 666.319863] __kmalloc_noprof+0x1e7/0x520 [ 666.319867] sock_kmalloc+0xdf/0x130 [ 666.319885] sock_kmemdup+0x1b/0x40 [ 666.319888] mptcp_userspace_pm_append_new_local_addr+0x261/0x500 [ 666.319910] mptcp_pm_nl_announce_doit+0x16a/0x610 ... [ 666.319967] Freed by task 45560: [ 666.319988] kasan_save_stack+0x33/0x60 [ 666.319991] kasan_save_track+0x14/0x30 [ 666.319994] kasan_save_free_info+0x3b/0x60 [ 666.319998] __kasan_slab_free+0x43/0x70 [ 666.320000] kfree+0x166/0x440 [ 666.320003] sock_kfree_s+0x1d/0x50 [ 666.320007] mptcp_userspace_pm_delete_local_addr.isra.0+0x157/0x200 [ 666.320011] mptcp_pm_nl_subflow_destroy_doit+0x51d/0xea0 Fix by copying the id into a local variable while still holding the lock, and use -1 as a "not found" sentinel.

In the Linux kernel, the following vulnerability has been resolved: tipc: clear sock->sk on the failed-insert path in tipc_sk_create() When tipc_sk_create() fails to insert the new socket (tipc_sk_insert() returns non-zero), its error path frees the sk with sk_free() but leaves sock->sk pointing at the freed object: if (tipc_sk_insert(tsk)) { sk_free(sk); pr_warn("Socket create failed; port number exhausted\n"); return -EINVAL; } This is harmless for plain socket(): the syscall layer clears sock->ops before releasing, so tipc_release() is never called. It is not harmless on the accept() path. tipc_accept() creates the pre-allocated child socket with tipc_sk_create(net, new_sock, 0, kern); on failure it leaves new_sock->sk dangling and new_sock->ops non-NULL, and do_accept() then fput()s the new file, so __sock_release() -> tipc_release() runs lock_sock(new_sock->sk) on the freed sk -- a use-after-free write of the sk_lock spinlock. tipc_release() already guards this exact "failed accept() releases a pre-allocated child" case with "if (sk == NULL) return 0;", but the guard is bypassed because tipc_sk_create() left sock->sk non-NULL (dangling) rather than NULL. Clear sock->sk on the failed-insert path so the existing tipc_release() NULL check fires and the use-after-free is avoided. The tipc_sk_insert() failure is reached when the per-netns socket rhashtable hits its max_size (tsk_rht_params.max_size = 1048576, ~2M elements) -- i.e. once a netns holds ~2M TIPC sockets every insert returns -E2BIG. BUG: KASAN: slab-use-after-free in lock_sock_nested (net/core/sock.c:3839) Write of size 8 at addr ffff8880047cdc38 by task init/1 lock_sock_nested (net/core/sock.c:3839) tipc_release (net/tipc/socket.c:638) __sock_release (net/socket.c:710) sock_close (net/socket.c:1501) __fput (fs/file_table.c:512) Allocated by task 1: sk_alloc (net/core/sock.c:2308) tipc_sk_create (net/tipc/socket.c:487) tipc_accept (net/tipc/socket.c:2744) do_accept (net/socket.c:2034) Freed by task 1: __sk_destruct (net/core/sock.c:2391) tipc_sk_create (net/tipc/socket.c:504) tipc_accept (net/tipc/socket.c:2744) do_accept (net/socket.c:2034)

This CVE ID has been rejected or withdrawn by its CVE Numbering Authority.

In the Linux kernel, the following vulnerability has been resolved: fuse-uring: fix race between registration and connection abortion This fixes this race: - thread a: io_uring_enter -> register sqe -> fuse_uring_create_ring_ent -> allocate ent but doesn't grab queue_ref yet - thread b: fuse_conn_destroy() -> fuse_chan_abort() -> fuse_uring_abort() is a no-op due to queue ref being 0 - thread a: grabs the queue_ref, queue_ref is now 1, rest of fuse_uring_do_register() logic executes - thread b: fuse_chan_abort() returns, fuse_chan_wait_aborted() now runs and calls "wait_event(ring->stop_waitq, atomic_read(&ring->queue_refs) == 0);" The abort/unmount thread will hang indefinitely in unkillable state as nothing will decrement queue_refs or wake stop_waitq, and the ring, queue, and ent are leaked. Fix this by checking fch->connected under fch->lock after the created ent has grabbed a ref count on the queue. This ensures that in the scenario above, it is guaranteed that we either release the queue ref and wake up stop_waitq (in case fuse_chan_wait_aborted() is already waiting) in fuse_uring_do_register() when we detect !fch->connected, or if the connection is aborted after the check, it is guaranteed that the async teardown worker will be running in the background cleaning up ents and decrementing the ent's ref on the queue, which will unblock the eventual queue and ring teardown.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_uart: clear HCI_UART_SENDING when write_work is canceled HCI_UART_SENDING bit in tx_state means write_work is pending and blocks queueing it again. Currently this bit is not cleared when canceling the work in hci_uart_close(), which blocks future writes when device is reopened later if write_work was pending. Fix by clearing HCI_UART_SENDING when canceling the work. Also make clearing of tx_skb safe by using disable_work_sync + enable_work instead of just cancel_work_sync. hci_uart_flush() purges the proto tx queue so we can cancel the pending write_work there, instead of doing it just in hci_uart_close(). Re-enable and possibly requeue the work after queue flush.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix potential buffer underflow in ath11k_hal_rx_msdu_list_get() When the first entry in msdu_details has a zero buffer address, the code accesses msdu_details[i - 1] with i == 0, causing a buffer underflow. Fix similarly to ath12k_wifi7_hal_rx_msdu_list_get() by adding a separate check for i == 0 before the main condition to prevent the out-of-bounds access. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: binfmt_elf_fdpic: only honour the first PT_INTERP The program header scan handles PT_INTERP from a switch nested in the scan loop, so its break leaves the switch and not the loop. A binary carrying more than one PT_INTERP runs the case again and overwrites both interpreter_name and interpreter. The previous name allocation leaks and so does the previous interpreter reference, along with the write denial open_exec() took on it. The denial is never released, so the file stays unwritable for as long as the system runs. An unprivileged caller reaches this with a crafted binary and repeats it at will. binfmt_elf stops at the first PT_INTERP. Do the same here. The flaw dates back to the driver's introduction in the pre-git history tree introduced in v2.6.11 by 91808d6ebe39 ("[PATCH] FRV: Add FDPIC ELF binary format driver").

In the Linux kernel, the following vulnerability has been resolved: time/jiffies: Register jiffies clocksource before usage Teddy reported that a XEN HVM has a long boot delay, which was bisected to the recent enhancements to the negative motion detection. It turned out that the jiffies clocksource is used in early boot before it is registered, which leaves the max_delta_raw field at zero. That causes the read out to be clamped to the max delta of 0, which means time is not making progress. Cure it by ensuring that it is initialized before its first usage in timekeeping_init().

In the Linux kernel, the following vulnerability has been resolved: sctp: validate stream count in sctp_process_strreset_inreq() When processing a RESET_IN_REQUEST from a peer, sctp_process_strreset_inreq() derives the stream count from the parameter length but does not check whether the resulting RESET_OUT_REQUEST would exceed SCTP_MAX_CHUNK_LEN. The OUT request header (sctp_strreset_outreq, 16 bytes) is 8 bytes larger than the IN request header (sctp_strreset_inreq, 8 bytes). Generally, the IP payload is bounded to 65535 bytes, so the stream list cannot be large enough to trigger the overflow. However, on interfaces with MTU > 65535 (e.g., loopback with IPv6 jumbograms), a stream list that fits within the incoming IN parameter can cause a __u16 overflow in sctp_make_strreset_req() when computing the OUT request size, leading to an undersized skb allocation and a kernel BUG: net/core/skbuff.c:207 skb_panic net/core/skbuff.c:2625 skb_put net/sctp/sm_make_chunk.c:1535 sctp_addto_chunk net/sctp/sm_make_chunk.c:3695 sctp_make_strreset_req net/sctp/stream.c:655 sctp_process_strreset_inreq The local setsockopt path validates the generated reset request size. However, for an incoming-only reset, it accounts for the smaller IN request even though the peer must generate an OUT request with the same stream list. Such a request cannot be completed successfully by the peer. Reject peer IN requests whose corresponding OUT request would exceed SCTP_MAX_CHUNK_LEN. Also tighten the local check so it does not send an IN request that would require an oversized OUT request from the peer.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Move jump_label_init() before parse_early_param() When enabling both CONFIG_MEM_ALLOC_PROFILING=y and CONFIG_MEM_ALLOC_PROFILING_ENABLED_BY_DEFAULT=y, then diabling memory profiling by adding the boot parameter 'sysctl.vm.mem_profiling=0' will cause the kernel failed to boot. After analysis, this is because jump_label_init() must be called before parse_early_param(), the early param handlers may modify static keys by static_branch_enable/disable(). Fix this by moving jump_label_init() to before parse_early_param(). The solution is similar to other architectures.

In the Linux kernel, the following vulnerability has been resolved: sched_ext: Preserve rq tracking across local DSQ dispatch dispatch_to_local_dsq() can run from scx_bpf_dsq_move_to_local() while ops.dispatch() has recorded the current rq. Moving a task to a local DSQ may switch to the source or destination rq before synchronously invoking ops.dequeue() through the following path: SCX_CALL_OP(dispatch, rq) ops.dispatch() scx_bpf_dsq_move_to_local() scx_flush_dispatch_buf() finish_dispatch() dispatch_to_local_dsq() scx_dispatch_enqueue() local_dsq_post_enq() call_task_dequeue() SCX_CALL_OP_TASK(dequeue, locked_rq, ...) The nested callback saves the recorded rq and restores it on return. If the rq tracking does not follow the lock switch, update_locked_rq() can trigger the following lockdep assertion while restoring an rq which is no longer held: WARNING: kernel/sched/sched.h:1641 at call_task_dequeue+0x160/0x170 Call Trace: scx_dispatch_enqueue+0x2b0/0x460 dispatch_to_local_dsq+0x138/0x230 scx_flush_dispatch_buf+0x1af/0x220 scx_bpf_dsq_move_to_local___v2+0xe2/0x1c0 bpf__sched_ext_ops_dispatch+0x4b/0xa7 do_pick_task_scx+0x3b6/0x910 __pick_next_task+0x105/0x1f0 __schedule+0x3e7/0x1980 Introduce switch_rq_lock() to update the tracking state together with each rq lock handoff. Use it in dispatch_to_local_dsq(), move_remote_task_to_local_dsq() and the in-balance paths of scx_dsq_move(), ensuring that scx_locked_rq() consistently refers to the rq whose lock is actually held throughout the lock dance.

In the Linux kernel, the following vulnerability has been resolved: drm/imagination: fix error checking of pvr_vm_context_lookup() Since pvr_vm_context_lookup() returns either NULL or a pointer, then stop using IS_ERR() for checking the return value. Using IS_ERR() leads to the kernel oops reported below. It can be reproduced by passing an invalid VM context handle from userspace to the DRM_IOCTL_PVR_CREATE_CONTEXT ioctl. [ 92.733119] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000148 [ 92.742042] Mem abort info: [ 92.744890] ESR = 0x0000000096000004 [ 92.748686] EC = 0x25: DABT (current EL), IL = 32 bits [ 92.754020] SET = 0, FnV = 0 [ 92.757154] EA = 0, S1PTW = 0 [ 92.760337] FSC = 0x04: level 0 translation fault [ 92.765243] Data abort info: [ 92.768129] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 92.773626] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 92.778763] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 92.784098] user pgtable: 4k pages, 48-bit VAs, pgdp=000000088ed23000 [ 92.790550] [0000000000000148] pgd=0000000000000000, p4d=0000000000000000 [ 92.797381] Internal error: Oops: 0000000096000004 [#1] SMP [ 92.803027] Modules linked in: powervr [ 92.852533] CPU: 0 UID: 0 PID: 409 Comm: triangle Not tainted 7.1.0-rc5-g98b46e693b91 #1 PREEMPT [ 92.861385] Hardware name: Texas Instruments AM68 SK (DT) [ 92.866766] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 92.873709] pc : pvr_vm_get_fw_mem_context+0x0/0xc [powervr] [ 92.879376] lr : pvr_queue_create+0x26c/0x440 [powervr] [ 92.884595] sp : ffff8000837fbb00 [ 92.887895] x29: ffff8000837fbb60 x28: 0000000000000000 x27: ffff8000837fbce8 [ 92.895015] x26: ffff000807f61a40 x25: ffff000807f61a00 x24: ffff000807f64400 [ 92.902135] x23: ffff00080a5ab000 x22: ffff800079b24730 x21: ffff000807f61800 [ 92.909254] x20: ffff00080999e680 x19: 0000000000000000 x18: 0000000000000000 [ 92.916373] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000001 [ 92.923492] x14: 0000000000000000 x13: 0000000000000002 x12: ffff80008145b298 [ 92.930611] x11: ffff8000844e5000 x10: ffff80008165a130 x9 : 0000000000000100 [ 92.937730] x8 : 0000000000000001 x7 : ffff0008076b27e0 x6 : ffff00080ec43b7c [ 92.944850] x5 : ffff00080ec43b78 x4 : 0000000000000000 x3 : ffff00080999e680 [ 92.951968] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 [ 92.959088] Call trace: [ 92.961521] pvr_vm_get_fw_mem_context+0x0/0xc [powervr] (P) [ 92.967173] pvr_context_create+0x190/0x410 [powervr] [ 92.972218] pvr_ioctl_create_context+0x44/0x8c [powervr] [ 92.977608] drm_ioctl_kernel+0xbc/0x124 [drm] [ 92.982127] drm_ioctl+0x1f8/0x4dc [drm] [ 92.986098] __arm64_sys_ioctl+0xac/0x104 [ 92.990102] invoke_syscall+0x54/0x10c [ 92.993842] el0_svc_common.constprop.0+0x40/0xe0 [ 92.998532] do_el0_svc+0x1c/0x28 [ 93.001835] el0_svc+0x38/0x11c [ 93.004969] el0t_64_sync_handler+0xa0/0xe4 [ 93.009139] el0t_64_sync+0x198/0x19c [ 93.012792] Code: aa1703e0 d2800014 95cb0ba4 17ffffe8 (f940a400) [ 93.018869] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: debugobjects: Plug race against a concurrent OOM disable syzbot reported a puzzling splat: WARNING: kernel/time/hrtimer.c:443 at stub_timer+0xa/0x20 stub_timer() is installed as timer callback function in hrtimer_fixup_assert_init(), which is invoked when debug_object_assert_init() can't find a shadow object. In that case debug objects emits a warning about it before invoking the fixup. Though the provided console log lacks this warning and instead has the following a few seconds before the splat: ODEBUG: Out of memory. ODEBUG disabled So the object was looked up in debug_object_assert_init() and the lookup failed due a concurrent out of memory situation which disabled debug objects and freed the shadow objects: debug_object_assert_init() if (!debug_objects_enabled) return; obj = alloc(); if (!obj) { // Out of memory debug_objects_enabled = false; free_objects(); obj = lookup_or_alloc(); // The lookup failed because the other side // removed the objects, so this returns // an error code as the object in question // is not statically initialized if (!IS_ERR_OR_NULL(obj)) return; if (!obj) { debug_oom(); return; } print(...) if (!debug_objects_enabled) return; fixup(...) The debug object splat is skipped because debug_objects_enabled is false, but the fixup callback is invoked unconditionally, which makes the timer disfunctional. This is only a problem in debug_object_assert_init() and debug_object_activate() as both have to handle statically initialized objects and therefore must handle the error pointer return case gracefully. All other places only handle the found/not found case and the NULL pointer return is a signal for OOM. Otherwise they get a valid shadow object. Plug the hole by checking whether debug objects are still enabled before invoking the print and fixup function in those two places.

In the Linux kernel, the following vulnerability has been resolved: HID: wacom: use GFP_ATOMIC in wacom_wac_queue_flush() wacom_wac_queue_flush() is called via the .raw_event callback (wacom_raw_event → wacom_wac_pen_serial_enforce → wacom_wac_queue_flush). For USB HID devices, this callback is invoked from hid_irq_in(), which is a URB completion handler running in atomic context. Using GFP_KERNEL in this path can sleep, leading to a "scheduling while atomic" bug. Use GFP_ATOMIC instead. The existing code already handles allocation failure by skipping the fifo entry and continuing.

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Fix use-after-free of mm_struct in job scheduler amdxdna_cmd_submit() stores current->mm in job->mm without holding any reference. aie2_sched_job_run() later access job->mm from the DRM scheduler worker thread. With only a raw pointer and no structural reference, the mm_struct can be freed before the scheduler runs the job. Fix this by calling mmgrab() to hold a structural mm_count reference for the lifetime of the job, paired with mmdrop() in every cleanup path.

In the Linux kernel, the following vulnerability has been resolved: tracing: Delay module ref count for "enable_event" trigger Triggers are now delayed from freeing, but can still be triggered until after the RCU grace period has ended. The freeing of the enable_event data is put into the private_data_free() callback, but the put of the module refcount is done immediately. It is possible that if a module is removed that has an event that would enable (or disable) it is still active, it can read the data of the module after it is removed causing a use-after-free bug. Move the trace_event_put_ref() that releases the module into the delayed callback so that the module can not be removed until any reference to its events are finished.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: cancel sched scan results work on unregister cfg80211_sched_scan_results() can queue rdev->sched_scan_res_wk from a driver result notification while a scheduled scan request is present. The work callback recovers the containing cfg80211_registered_device and then locks the wiphy and walks the scheduled-scan request list. wiphy_unregister() already makes the wiphy unreachable and drains rdev work items before cfg80211_dev_free() can release the object, but it does not drain sched_scan_res_wk. A queued or running result work item can therefore cross the unregister/free boundary and access freed rdev state. The buggy scenario involves two paths, with each column showing the order within that path: scheduled-scan result path: unregister/free path: 1. cfg80211_sched_scan_results() 1. interface teardown stops and queues rdev->sched_scan_res_wk. removes the scheduled scan request. 2. cfg80211_wq starts the work 2. wiphy_unregister() drains other item and recovers rdev. rdev work items. 3. The worker locks rdev->wiphy 3. cfg80211_dev_free() destroys and and walks rdev state. frees rdev. Cancel sched_scan_res_wk in wiphy_unregister() alongside the other rdev work items. cancel_work_sync() removes a pending result notification and waits for an already running callback, so cfg80211_dev_free() cannot free rdev while this work item is still active. Validation reproduced this kernel report: BUG: KASAN: use-after-free in cfg80211_sched_scan_results_wk+0x4a6/0x530 Workqueue: cfg80211 cfg80211_sched_scan_results_wk [cfg80211] Read of size 8 Call trace: dump_stack_lvl+0x66/0xa0 print_report+0xce/0x630 cfg80211_sched_scan_results_wk+0x4a6/0x530 srso_alias_return_thunk+0x5/0xfbef5 __virt_addr_valid+0x224/0x430 kasan_report+0xac/0xe0 lockdep_hardirqs_on_prepare+0xea/0x1a0 process_one_work+0x8d0/0x18f0 (kernel/workqueue.c:3212) lock_is_held_type+0x8f/0x100 worker_thread+0x5ad/0xfd0 __kthread_parkme+0xc6/0x200 kthread+0x31e/0x410 trace_hardirqs_on+0x1a/0x170 ret_from_fork+0x576/0x810 __switch_to+0x57e/0xe20 __switch_to_asm+0x33/0x70 ret_from_fork_asm+0x1a/0x30