⌘ + K

CVE Feed

9.8

Critical

CVE-2026-72209

Last Modified: 22 Aug 2026

In the Linux kernel, the following vulnerability has been resolved: ntfs: validate attribute values on lookup ntfs_attr_find() and ntfs_external_attr_find() check that generic resident attribute values fit in their attribute records and that fixed-size resident values are large enough. For variable-length resident formats, however, the fixed part is not enough: embedded length fields can still point callers past the resident value. A crafted image can set a small resident $FILE_NAME value_length while leaving file_name_length large. Callers then trust file_name_length and read past the resident value when converting or comparing the name. This was reproduced with a crafted image under KASAN as a slab-out-of-bounds read from the kmalloc-1k MFT record copy. The stack included ntfs_lookup(), ntfs_iget(), ntfs_read_locked_inode(), ntfs_attr_name_get(), ntfs_ucstonls(), and utf16s_to_utf8s(). Add a shared attribute value validator and use it before a lookup path can return an attribute, including the AT_UNUSED enumeration case where callers inspect returned attributes directly. The helper validates resident value bounds, minimum resident value sizes, variable-length $FILE_NAME fields, and non-resident mapping-pairs metadata that was previously checked separately in both lookup paths. This also preserves the intended resident @val matching semantics in the external attribute lookup path. The old duplicated validation block overwrote the actual resident value length with the type-specific minimum length before comparing @val, so variable-length resident values could fail to match even when the bytes were identical. Keep the comparison on the actual value length, and make ntfs_attrlist_entry_add() compare resident attributes with lowest_vcn zero instead of reading the non-resident union member after a successful resident match. Reject non-resident $FILE_NAME records too: the format requires $FILE_NAME to be resident and callers treat returned records as resident.

Published: 15 Aug 2026

5.5

Medium

Last Modified: 16 Oct 2026

In the Linux kernel, the following vulnerability has been resolved: RDMA/srpt: fix integer overflow in immediate data length check imm_buf->len is a user-controlled uint32_t received from the network. Adding it to imm_data_offset without overflow checking allows a malicious initiator to send len=0xFFFFFFFF, causing req_size to wrap around to a small value, bypassing the bounds check, and subsequently passing a ~4GB length to sg_init_one(). Use check_add_overflow() to detect wrapping before the comparison.

Published: 15 Aug 2026

7.5

High

Last Modified: 22 Aug 2026

In the Linux kernel, the following vulnerability has been resolved: spi: xilinx: use FIFO occupancy register to determine buffer size The method the driver uses to determine the size of the FIFO has a problem. What it currently does is this: It stops the SPI hardware and writes to the TX FIFO register until TX FIFO FULL asserts in the status register. But the hardware does not only have the FIFO, it also has a shift register which can hold a byte. This can be seen, when writing a byte to the FIFO (while the SPI hardware is stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size of 16 for example, the current method returns a 17. This is a problem, at least when using the driver in irq mode. The same size determined for the TX FIFO is also assumed for the RX FIFO. When a SPI transaction wants to write the amount of the FIFO size or more bytes, the following happens, for example with 16 bytes FIFO size: The driver stops the SPI hardware and writes 17 bytes to the TX FIFO and starts the SPI hardware and goes sleep. The hardware then shifts out 17 bytes (FIFO + shift register) and simultaneously reads bytes into the RX FIFO, but it only has 16 places, so it looses one byte. Then TX FIFO empty asserts, wakes the driver again, which has a fast path and reads 16 bytes from the RX FIFO, but before reading the last 17th byte (which is lost) it does this: sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET); if (!(sr & XSPI_SR_RX_EMPTY_MASK)) { xilinx_spi_rx(xspi); rx_words--; } It reads the status register and checks if the RX FIFO is not empty. But it is empty in our case. So this check spins in a while loop forever locking the driver. This patch fixes the logic to determine the FIFO size.

Published: 15 Aug 2026

5.5

Medium

CVE-2026-74308

Last Modified: 30 Oct 2026

In the Linux kernel, the following vulnerability has been resolved: ext4: fix kernel BUG in ext4_write_inline_data_end When the data=journal mount option is used, the ext4_journalled_write_end() function incorrectly calls ext4_write_inline_data_end() without checking if the EXT4_STATE_MAY_INLINE_DATA flag is still set on the inode. If a previous attempt to convert the inline data to an extent failed (e.g. due to ENOSPC), the EXT4_STATE_MAY_INLINE_DATA flag is cleared, but the EXT4_INODE_INLINE_DATA flag remains set. In this scenario, the next call to ext4_write_begin() will not prepare the inline data xattr for writing, but ext4_journalled_write_end() will incorrectly attempt to write to it, triggering a BUG_ON(pos + len > EXT4_I(inode)->i_inline_size) in ext4_write_inline_data() since i_inline_size was not expanded. Fix this by ensuring that ext4_journalled_write_end() only calls ext4_write_inline_data_end() if the EXT4_STATE_MAY_INLINE_DATA flag is set, mirroring the behavior of ext4_write_end() and ext4_da_write_end().

Published: 15 Aug 2026

Items Per Page